|
4310应该是在我修改network.config时变砖了, 然后买了TTL线尝试刷回来. 但是每次开机后在AutoBoot时按TPL键都不顶用, 直接运行下去了, 请教该怎么办?
U-Boot 1.1.4 (Mar 19 2013 - 15:19:42)
U-boot DB120
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Mar 23 16:49:30 UTC 2013
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126464k/131072k available (2211k kernel code, 4608k reserved, 418k data, 212k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[ 0.090000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.310000] PCI host bridge to bus 0000:00
[ 0.320000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.330000] pci 0000:00:00.0: invalid calibration data
[ 0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.340000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.350000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.360000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.370000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.370000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.380000] TCP reno registered
[ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] NET: Registered protocol family 1
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.430000] msgmni has been set to 247
[ 0.430000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.440000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.490000] console [ttyS0] enabled, bootconsole disabled
[ 0.490000] console [ttyS0] enabled, bootconsole disabled
[ 0.500000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.510000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.510000] 5 tp-link partitions found on MTD device spi0.0
[ 0.520000] Creating 5 MTD partitions on "spi0.0":
[ 0.520000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.530000] 0x000000020000-0x000000110000 : "kernel"
[ 0.530000] 0x000000110000-0x0000007f0000 : "rootfs"
[ 0.540000] mtd: partition "rootfs" set to be root filesystem
[ 0.550000] split_squashfs: no squashfs found in "spi0.0"
[ 0.550000] 0x0000007f0000-0x000000800000 : "art"
[ 0.560000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.690000] ag71xx_mdio: probed
[ 0.700000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.280000] eth0: Atheros AR8327 switch driver attached.
[ 2.430000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 2.450000] TCP cubic registered
[ 2.450000] NET: Registered protocol family 17
[ 2.450000] Bridge firewalling registered
[ 2.460000] 8021q: 802.1Q VLAN Support v1.8
[ 3.410000] JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 3.430000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
[ 3.430000] Freeing unused kernel memory: 212k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
[ 6.440000] eth0: link up (1000Mbps/Full duplex)
- regular preinit -
- init -
[ 8.330000] eth0: link down
Please press Enter to activate this console. [ 8.940000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 8.950000] Backport based on wireless-testing.git master-2012-09-07
[ 8.960000] compat.git: wireless-testing.git
[ 9.070000] cfg80211: Calling CRDA to update world regulatory domain
[ 9.080000] cfg80211: World regulatory domain updated:
[ 9.080000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.090000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.100000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.110000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.120000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.120000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.280000] usbcore: registered new interface driver usbfs
[ 9.280000] usbcore: registered new interface driver hub
[ 9.290000] usbcore: registered new device driver usb
[ 9.760000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 9.770000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 9.790000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 9.800000] cfg80211: Calling CRDA for country: US
[ 9.800000] cfg80211: Regulatory domain changed to country: US
[ 9.810000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.810000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 9.820000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 9.830000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.840000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.850000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.850000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 9.910000] PPP generic driver version 2.4.2
[ 9.980000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.090000] NET: Registered protocol family 24
[ 10.130000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.130000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 10.140000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 10.180000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 10.200000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 10.200000] hub 1-0:1.0: USB hub found
[ 10.210000] hub 1-0:1.0: 1 port detected
[ 10.250000] nf_conntrack version 0.5.0 (1979 buckets, 7916 max)
[ 10.480000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.510000] uhci_hcd: USB Universal Host Controller Interface driver
[ 10.530000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 10.570000] usbcore: registered new interface driver usbserial
[ 10.580000] USB Serial support registered for generic
[ 10.680000] hub 1-1:1.0: USB hub found
[ 10.680000] hub 1-1:1.0: 4 ports detected
[ 10.690000] usbcore: registered new interface driver usbserial_generic
[ 10.690000] usbserial: USB Serial Driver core
|
|