谁熟悉TTL信息，帮我看下问题在哪

xia***

耍了不死uboot之后，怎么刷固件都不行，郁闷了，不管原厂，dd ，open编程器固件都不行，看下哪里问题吧
TTL每次都卡在这里了
U-Boot 1.1.4 (Apr 27 2015 - 09:16:56)

AP96 (AR7161 rev 2) U-Boot
DRAM:  128 MB
Flash: Macronix MX25L12835E (16 MB)
Using default environment

BOARD IS NOT CALIBRATED!!!
Clocks: CPU:680MHz, DDR:340MHz, AHB:170MHz, Ref:40MHz
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
No valid address in Flash. Using fixed MAC Address
No valid address in Flash. Using fixed MAC Address
GMAC: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
GMAC: cfg1 0xf cfg2 0x7014
eth1: 00:03:7f:09:0b:ad
eth1 up
eth0, eth1
Hit any key to stop autoboot:  0
### SQUASHFS loading 'image/uImage' to 0x80800000
### SQUASHFS load complete: 1012654 bytes loaded to 0x80800000
## Booting image at 80800000 ...
   Image Name:   MIPS Linux Kernel Image
   Created:      2013-03-25   9:03:22 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1012590 Bytes = 988.9 kB
   Load Address: 80002000
   Entry Point:  8022e950
   Verifying Checksum at 0x80800040 ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] bootconsole [early0] enabled
[    0.000000] booting platform Atheros AR7161 rev 2 (0xaa)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Linux version 3.5.7 (root@dd-wrt) (gcc version 4.7.3 20121205 (prerelease) (Linaro GCC 4.7-2012.12) ) #6152 Mon Mar 25 09:59:38 CET 2013
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 126688k/131072k available (2259k kernel code, 4384k reserved, 491k data, 164k init, 0k highmem)
[    0.000000] NR_IRQS:80
[    0.000000] irq init done
[    0.000000] plat_time_init: plat time init done
[    0.000000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 512
[    0.070000] NET: Registered protocol family 16
[    3.070000] registering PCI controller with io_map_base unset
[    3.080000] bio: create slab <bio-0> at 0
[    3.090000] PCI host bridge to bus 0000:00
[    3.090000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[    3.100000] pci_bus 0000:00: root bus resource [io  0x0000]

8***

不懂帮顶

che***

要是用H大的UB就是不死UB的问题，用编程器刷个包涵不死UB的编程器固件即可 ，刷完启动完毕再进UB刷固件即可

xia***

cheapjr 发表于 2016-1-16 15:18
要是用H大的UB就是不死UB的问题，用编程器刷个包涵不死UB的编程器固件即可 ，刷完启动完毕再进UB刷固件即可

我刷H大的不死是这情况，刷原厂UBOOT的话一直卡在英文开启内核那一点

che***

xiahui 发表于 2016-1-17 12:41
我刷H大的不死是这情况，刷原厂UBOOT的话一直卡在英文开启内核那一点

不用原厂的UB，直接用H大的UB自己用WIHEX合成革编程器固件就好了

xia***

cheapjr 发表于 2016-1-17 22:10
不用原厂的UB，直接用H大的UB自己用WIHEX合成革编程器固件就好了

明天我试试看

chanw***

上面有英文提示，，u-boot和 板子 不匹配

xia***

chanwah2009 发表于 2016-1-18 15:42
上面有英文提示，，u-boot和 板子 不匹配

很是郁闷，UBOOT换了原厂也是过不去，原厂备份找不到了