LEDE op多线多拨的解决办法

cc***

先上路由图
从图上可以看到，3条线路，每条线路都需要多拨
目前lede的op是无法实现的。我用的是koolshare论坛的fw867版的LEDE Reboot r1770 『 X64.1.8 R1 』 by fw867
我的思路是，用旧的macvlan多拨办法，手动针对每个端口设置macvlan，然后分线路统一ifdown，ifup来实现多拨
不知道有没有人这么试过，可不可行。
另外，不知道lede的macvlan创建代码在哪个文件里面，传统op我曾经找到了，lede的没有看到
求高手指点

cc***

LEDE运行于esxi的虚拟机系统里面电信、移动，移动，3个网口都做了直通
我目前已经弄好了电信的双拨，使用旧的macvlan创建方式，并且添加了一个wanA，一个wanB
分别用于两个移动线路的拨号
但是发现这两个移动线路基本上无法拨上号，不知道啥原因
后面附上系统日志以及内核日志

cc***

系统日志


Mon Oct 17 15:01:34 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:01:34 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:01:34 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:01:34 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:01:34 2016 kern.info kernel: [50489.237921] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:01:34 2016 kern.info kernel: [50489.238164] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:01:41 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:01:41 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:01:41 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:01:41 2016 kern.info kernel: [50495.965517] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:01:41 2016 kern.info kernel: [50495.966219] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:01:41 2016 daemon.info pppd[7502]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:01:41 2016 daemon.info pppd[7502]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:01:41 2016 daemon.notice pppd[7502]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:01:42 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:01:42 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:01:42 2016 kern.info kernel: [50497.094989] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:01:49 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:01:49 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:01:49 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:01:49 2016 kern.info kernel: [50503.875872] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:01:49 2016 daemon.info pppd[7562]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:01:49 2016 daemon.info pppd[7562]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:01:49 2016 daemon.notice pppd[7562]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:01:50 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:01:50 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:01:50 2016 kern.info kernel: [50504.995308] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:01:55 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:01:55 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:01:55 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:01:55 2016 kern.info kernel: [50510.586613] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:01:55 2016 daemon.info pppd[7613]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:01:55 2016 daemon.info pppd[7613]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:01:56 2016 daemon.notice pppd[7613]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:02:11 2016 daemon.warn pppd[7613]: Timeout waiting for PADO packets
Mon Oct 17 15:02:11 2016 daemon.err pppd[7613]: Unable to complete PPPoE Discovery
Mon Oct 17 15:02:11 2016 daemon.info pppd[7613]: Exit.
Mon Oct 17 15:02:11 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:02:11 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:02:11 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:02:11 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:02:11 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:02:11 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:02:11 2016 kern.info kernel: [50525.777727] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:02:11 2016 kern.info kernel: [50525.777972] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:02:14 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:02:14 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:02:14 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:02:14 2016 kern.info kernel: [50528.696992] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:02:14 2016 kern.info kernel: [50528.697695] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:02:14 2016 daemon.info pppd[7724]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:02:14 2016 daemon.info pppd[7724]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:02:14 2016 daemon.notice pppd[7724]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:02:15 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:02:15 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:02:15 2016 kern.info kernel: [50529.826454] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:02:21 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:02:21 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:02:21 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:02:21 2016 kern.info kernel: [50536.507352] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:02:21 2016 daemon.info pppd[7781]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:02:21 2016 daemon.info pppd[7781]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:02:21 2016 daemon.notice pppd[7781]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:02:22 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:02:22 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:02:23 2016 kern.info kernel: [50537.626786] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:02:29 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:02:29 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:02:29 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:02:29 2016 kern.info kernel: [50544.307733] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:02:29 2016 daemon.info pppd[7837]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:02:29 2016 daemon.info pppd[7837]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:02:29 2016 daemon.notice pppd[7837]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:02:30 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:02:30 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:02:30 2016 kern.info kernel: [50545.437149] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:02:32 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:02:32 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:02:32 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:02:32 2016 kern.info kernel: [50547.077830] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:02:35 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:02:35 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:02:35 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:02:35 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:02:35 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:02:35 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:02:35 2016 kern.info kernel: [50550.498738] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:02:35 2016 kern.info kernel: [50550.498981] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:02:42 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:02:42 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:02:42 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:02:42 2016 kern.info kernel: [50557.208301] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:02:42 2016 kern.info kernel: [50557.209005] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:02:42 2016 daemon.info pppd[7926]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:02:42 2016 daemon.info pppd[7926]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:02:42 2016 daemon.notice pppd[7926]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:02:43 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:02:43 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:02:43 2016 kern.info kernel: [50558.327658] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:02:50 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:02:50 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:02:50 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:02:50 2016 kern.info kernel: [50565.008662] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:02:50 2016 daemon.info pppd[7983]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:02:50 2016 daemon.info pppd[7983]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:02:50 2016 daemon.notice pppd[7983]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:02:51 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:02:51 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:02:51 2016 kern.info kernel: [50566.128036] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:02:56 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:02:56 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:02:56 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:02:56 2016 kern.info kernel: [50571.529024] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:02:56 2016 daemon.info pppd[8038]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:02:56 2016 daemon.info pppd[8038]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:02:56 2016 daemon.notice pppd[8038]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:03:12 2016 daemon.warn pppd[8038]: Timeout waiting for PADO packets
Mon Oct 17 15:03:12 2016 daemon.err pppd[8038]: Unable to complete PPPoE Discovery
Mon Oct 17 15:03:12 2016 daemon.info pppd[8038]: Exit.
Mon Oct 17 15:03:12 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:03:12 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:03:12 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:03:12 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:03:12 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:03:12 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:03:12 2016 kern.info kernel: [50586.750529] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:03:12 2016 kern.info kernel: [50586.750773] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:03:15 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:03:15 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:03:15 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:03:15 2016 kern.info kernel: [50589.799764] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:03:15 2016 kern.info kernel: [50589.800461] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:03:15 2016 daemon.info pppd[8149]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:03:15 2016 daemon.info pppd[8149]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:03:15 2016 daemon.notice pppd[8149]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:03:16 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:03:16 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:03:16 2016 kern.info kernel: [50590.919221] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:03:22 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:03:22 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:03:22 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:03:22 2016 kern.info kernel: [50597.550142] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:03:22 2016 daemon.info pppd[8206]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:03:22 2016 daemon.info pppd[8206]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:03:22 2016 daemon.notice pppd[8206]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:03:24 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:03:24 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:03:24 2016 kern.info kernel: [50598.679453] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:03:30 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:03:30 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:03:30 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:03:30 2016 kern.info kernel: [50605.480483] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:03:30 2016 daemon.info pppd[8262]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:03:30 2016 daemon.info pppd[8262]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:03:30 2016 daemon.notice pppd[8262]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:03:31 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:03:31 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:03:31 2016 kern.info kernel: [50606.609905] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:03:33 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:03:33 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:03:33 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:03:33 2016 kern.info kernel: [50608.210590] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:03:36 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:03:37 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:03:37 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:03:37 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:03:37 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:03:37 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:03:37 2016 kern.info kernel: [50611.671485] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:03:37 2016 kern.info kernel: [50611.671729] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:03:43 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:03:43 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:03:43 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:03:43 2016 kern.info kernel: [50618.381074] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:03:43 2016 kern.info kernel: [50618.381767] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:03:43 2016 daemon.info pppd[8352]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:03:43 2016 daemon.info pppd[8352]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:03:43 2016 daemon.notice pppd[8352]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:03:44 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:03:44 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:03:44 2016 kern.info kernel: [50619.510460] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:03:51 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:03:51 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:03:51 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:03:51 2016 kern.info kernel: [50626.181447] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:03:51 2016 daemon.info pppd[8409]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:03:51 2016 daemon.info pppd[8409]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:03:51 2016 daemon.notice pppd[8409]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:03:52 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:03:52 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:03:52 2016 kern.info kernel: [50627.310781] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:03:58 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:03:58 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:03:58 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:03:58 2016 kern.info kernel: [50632.711727] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:03:58 2016 daemon.info pppd[8464]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:03:58 2016 daemon.info pppd[8464]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:03:58 2016 daemon.notice pppd[8464]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:04:13 2016 daemon.warn pppd[8464]: Timeout waiting for PADO packets
Mon Oct 17 15:04:13 2016 daemon.err pppd[8464]: Unable to complete PPPoE Discovery
Mon Oct 17 15:04:13 2016 daemon.info pppd[8464]: Exit.
Mon Oct 17 15:04:13 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:04:13 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:04:13 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:04:13 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:04:13 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:04:13 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:04:13 2016 kern.info kernel: [50647.893912] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:04:13 2016 kern.info kernel: [50647.894159] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:04:16 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:04:16 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:04:16 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:04:16 2016 kern.info kernel: [50650.862599] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:04:16 2016 kern.info kernel: [50650.863435] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:04:16 2016 daemon.info pppd[8688]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:04:16 2016 daemon.info pppd[8688]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:04:16 2016 daemon.notice pppd[8688]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:04:17 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:04:17 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:04:17 2016 kern.info kernel: [50651.991905] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:04:24 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:04:24 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:04:24 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:04:24 2016 kern.info kernel: [50659.132907] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:04:24 2016 daemon.info pppd[8774]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:04:24 2016 daemon.info pppd[8774]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:04:24 2016 daemon.notice pppd[8774]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:04:25 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:04:25 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:04:25 2016 kern.info kernel: [50660.252366] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:04:32 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:04:32 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:04:32 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:04:32 2016 kern.info kernel: [50666.933266] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:04:32 2016 daemon.info pppd[8886]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:04:32 2016 daemon.info pppd[8886]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:04:32 2016 daemon.notice pppd[8886]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:04:33 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:04:33 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:04:33 2016 kern.info kernel: [50668.052663] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:04:35 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:04:35 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:04:35 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:04:35 2016 kern.info kernel: [50669.683473] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:04:38 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:04:38 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:04:38 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:04:38 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:04:38 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:04:38 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:04:38 2016 kern.info kernel: [50673.116390] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:04:38 2016 kern.info kernel: [50673.116633] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:04:45 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:04:45 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:04:45 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:04:45 2016 kern.info kernel: [50679.823869] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:04:45 2016 kern.info kernel: [50679.824567] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:04:45 2016 daemon.info pppd[9059]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:04:45 2016 daemon.info pppd[9059]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:04:45 2016 daemon.notice pppd[9059]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:04:46 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:04:46 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:04:46 2016 kern.info kernel: [50680.953231] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:04:52 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:04:52 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:04:52 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:04:52 2016 kern.info kernel: [50687.634184] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:04:53 2016 daemon.info pppd[9144]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:04:53 2016 daemon.info pppd[9144]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:04:53 2016 daemon.notice pppd[9144]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:04:54 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:04:54 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:04:54 2016 kern.info kernel: [50688.753522] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:04:59 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:04:59 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:04:59 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:04:59 2016 kern.info kernel: [50694.164488] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:04:59 2016 daemon.info pppd[9226]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:04:59 2016 daemon.info pppd[9226]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:04:59 2016 daemon.notice pppd[9226]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:05:14 2016 daemon.warn pppd[9226]: Timeout waiting for PADO packets
Mon Oct 17 15:05:14 2016 daemon.err pppd[9226]: Unable to complete PPPoE Discovery
Mon Oct 17 15:05:14 2016 daemon.info pppd[9226]: Exit.
Mon Oct 17 15:05:14 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:05:14 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:05:14 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:05:14 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:05:14 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:05:14 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:05:14 2016 kern.info kernel: [50709.376620] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:05:14 2016 kern.info kernel: [50709.376868] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:05:17 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:05:17 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:05:17 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:05:17 2016 kern.info kernel: [50712.315342] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:05:17 2016 kern.info kernel: [50712.316040] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:05:17 2016 daemon.info pppd[9393]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:05:17 2016 daemon.info pppd[9393]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:05:17 2016 daemon.notice pppd[9393]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:05:18 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:05:18 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:05:18 2016 kern.info kernel: [50713.444658] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:05:25 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:05:25 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:05:25 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:05:25 2016 kern.info kernel: [50720.095685] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:05:25 2016 daemon.info pppd[9505]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:05:25 2016 daemon.info pppd[9505]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:05:25 2016 daemon.notice pppd[9505]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:05:26 2016 kern.info kernel: [50721.224999] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:05:26 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:05:26 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:05:26 2016 daemon.err uhttpd[2550]: cut: standard output: Broken pipe
Mon Oct 17 15:05:33 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:05:33 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:05:33 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:05:33 2016 kern.info kernel: [50727.896039] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:05:33 2016 daemon.info pppd[9706]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:05:33 2016 daemon.info pppd[9706]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:05:33 2016 daemon.notice pppd[9706]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:05:34 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:05:34 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:05:34 2016 kern.info kernel: [50729.025350] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:05:36 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:05:36 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:05:36 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:05:36 2016 kern.info kernel: [50730.676100] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:05:39 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:05:39 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:05:39 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:05:39 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:05:39 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:05:39 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:05:39 2016 kern.info kernel: [50734.089275] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:05:39 2016 kern.info kernel: [50734.089523] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:05:46 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:05:46 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:05:46 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:05:46 2016 kern.info kernel: [50740.966628] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:05:46 2016 kern.info kernel: [50740.967336] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:05:46 2016 daemon.info pppd[9797]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:05:46 2016 daemon.info pppd[9797]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:05:46 2016 daemon.notice pppd[9797]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:05:47 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:05:47 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:05:47 2016 kern.info kernel: [50742.085952] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:05:54 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:05:54 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:05:54 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:05:54 2016 kern.info kernel: [50748.766987] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:05:54 2016 daemon.info pppd[9854]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:05:54 2016 daemon.info pppd[9854]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:05:54 2016 daemon.notice pppd[9854]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:05:55 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:05:55 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:05:55 2016 kern.info kernel: [50749.886314] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:06:00 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:06:00 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:06:00 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:06:00 2016 kern.info kernel: [50755.287250] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:06:00 2016 daemon.info pppd[9910]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:06:00 2016 daemon.info pppd[9910]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:06:00 2016 daemon.notice pppd[9910]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:06:15 2016 daemon.warn pppd[9910]: Timeout waiting for PADO packets
Mon Oct 17 15:06:15 2016 daemon.err pppd[9910]: Unable to complete PPPoE Discovery
Mon Oct 17 15:06:15 2016 daemon.info pppd[9910]: Exit.
Mon Oct 17 15:06:15 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:06:15 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:06:15 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:06:15 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:06:15 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:06:15 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:06:15 2016 kern.info kernel: [50770.498658] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:06:15 2016 kern.info kernel: [50770.498901] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:06:18 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:06:18 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:06:18 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:06:18 2016 kern.info kernel: [50773.468046] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:06:18 2016 kern.info kernel: [50773.468747] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:06:18 2016 daemon.info pppd[10021]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:06:18 2016 daemon.info pppd[10021]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:06:18 2016 daemon.notice pppd[10021]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:06:19 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:06:19 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:06:19 2016 kern.info kernel: [50774.597402] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:06:26 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:06:26 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:06:26 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:06:26 2016 kern.info kernel: [50781.358400] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:06:26 2016 daemon.info pppd[10079]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:06:26 2016 daemon.info pppd[10079]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:06:26 2016 daemon.notice pppd[10079]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:06:27 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:06:27 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:06:27 2016 kern.info kernel: [50782.477769] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:06:34 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:06:34 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:06:34 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:06:34 2016 kern.info kernel: [50789.238744] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:06:34 2016 daemon.info pppd[10135]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:06:34 2016 daemon.info pppd[10135]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:06:34 2016 daemon.notice pppd[10135]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:06:35 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:06:35 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:06:35 2016 kern.info kernel: [50790.368180] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:06:37 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:06:37 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:06:37 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:06:37 2016 kern.info kernel: [50792.038965] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:06:40 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:06:40 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:06:40 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:06:40 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:06:40 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:06:40 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:06:40 2016 kern.info kernel: [50795.432482] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:06:40 2016 kern.info kernel: [50795.432728] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:06:47 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:06:47 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:06:47 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:06:47 2016 kern.info kernel: [50802.159418] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:06:47 2016 kern.info kernel: [50802.160120] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:06:47 2016 daemon.info pppd[10224]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:06:47 2016 daemon.info pppd[10224]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:06:47 2016 daemon.notice pppd[10224]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:06:48 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:06:48 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:06:48 2016 kern.info kernel: [50803.288701] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:06:55 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:06:55 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:06:55 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:06:55 2016 kern.info kernel: [50809.959781] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:06:55 2016 daemon.info pppd[10283]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:06:55 2016 daemon.info pppd[10283]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:06:55 2016 daemon.notice pppd[10283]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:06:56 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:06:56 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:06:56 2016 kern.info kernel: [50811.089057] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:07:01 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:07:01 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:07:01 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:07:01 2016 kern.info kernel: [50816.479967] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:07:01 2016 daemon.info pppd[10337]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:07:01 2016 daemon.info pppd[10337]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:07:01 2016 daemon.notice pppd[10337]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:07:16 2016 daemon.warn pppd[10337]: Timeout waiting for PADO packets
Mon Oct 17 15:07:16 2016 daemon.err pppd[10337]: Unable to complete PPPoE Discovery
Mon Oct 17 15:07:16 2016 daemon.info pppd[10337]: Exit.
Mon Oct 17 15:07:16 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:07:17 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:07:17 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:07:17 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:07:17 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:07:17 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:07:17 2016 kern.info kernel: [50831.701402] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:07:17 2016 kern.info kernel: [50831.701648] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:07:20 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:07:20 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:07:20 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:07:20 2016 kern.info kernel: [50834.670792] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:07:20 2016 kern.info kernel: [50834.671502] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:07:20 2016 daemon.info pppd[10451]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:07:20 2016 daemon.info pppd[10451]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:07:20 2016 daemon.notice pppd[10451]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:07:21 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:07:21 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:07:21 2016 kern.info kernel: [50835.790145] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:07:28 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:07:28 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:07:28 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:07:28 2016 kern.info kernel: [50842.711167] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:07:28 2016 daemon.info pppd[10508]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:07:28 2016 daemon.info pppd[10508]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:07:28 2016 daemon.notice pppd[10508]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:07:29 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:07:29 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:07:29 2016 kern.info kernel: [50843.820486] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:07:35 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:07:35 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:07:35 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:07:35 2016 kern.info kernel: [50850.611556] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:07:35 2016 daemon.info pppd[10565]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:07:35 2016 daemon.info pppd[10565]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:07:36 2016 daemon.notice pppd[10565]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:07:37 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:07:37 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:07:37 2016 kern.info kernel: [50851.730861] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:07:38 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:07:38 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:07:38 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:07:38 2016 kern.info kernel: [50853.421653] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:07:42 2016 daemon.notice netifd: Interface 'wanB' is now down
Mon Oct 17 15:07:42 2016 daemon.notice netifd: Interface 'wanB' is disabled
Mon Oct 17 15:07:42 2016 daemon.notice netifd: Interface 'wanB' is enabled
Mon Oct 17 15:07:42 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:07:42 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:07:42 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:07:42 2016 kern.info kernel: [50856.792466] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
Mon Oct 17 15:07:42 2016 kern.info kernel: [50856.792714] 8021q: adding VLAN 0 to HW filter on device eth3
Mon Oct 17 15:07:48 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:07:48 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:07:48 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:07:48 2016 kern.info kernel: [50863.512066] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:07:48 2016 kern.info kernel: [50863.512765] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
Mon Oct 17 15:07:48 2016 daemon.info pppd[10757]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:07:48 2016 daemon.info pppd[10757]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:07:48 2016 daemon.notice pppd[10757]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:07:49 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:07:49 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:07:49 2016 kern.info kernel: [50864.631474] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:07:56 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:07:56 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:07:56 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:07:56 2016 kern.info kernel: [50871.312433] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:07:56 2016 daemon.info pppd[10813]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:07:56 2016 daemon.info pppd[10813]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:07:56 2016 daemon.notice pppd[10813]: pppd 2.4.7 started by root, uid 0
Mon Oct 17 15:07:57 2016 daemon.notice netifd: Network device 'eth3' link is down
Mon Oct 17 15:07:57 2016 daemon.notice netifd: Interface 'wanB' has link connectivity loss
Mon Oct 17 15:07:57 2016 kern.info kernel: [50872.431790] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
Mon Oct 17 15:08:03 2016 daemon.notice netifd: Network device 'eth3' link is up
Mon Oct 17 15:08:03 2016 daemon.notice netifd: Interface 'wanB' has link connectivity
Mon Oct 17 15:08:03 2016 daemon.notice netifd: Interface 'wanB' is setting up now
Mon Oct 17 15:08:03 2016 kern.info kernel: [50877.832728] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
Mon Oct 17 15:08:03 2016 daemon.info pppd[10867]: Plugin rp-pppoe.so loaded.
Mon Oct 17 15:08:03 2016 daemon.info pppd[10867]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.7
Mon Oct 17 15:08:03 2016 daemon.notice pppd[10867]: pppd 2.4.7 started by root, uid 0

cc***

内核日志

[48938.479500] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[48945.150492] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[48946.279979] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[48952.951025] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[48954.080277] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[48955.731079] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[48959.143016] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[48959.143266] 8021q: adding VLAN 0 to HW filter on device eth3
[48966.041581] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[48966.042280] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[48967.171001] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[48973.841986] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[48974.971375] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[48980.352305] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[48995.576642] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[48995.576887] 8021q: adding VLAN 0 to HW filter on device eth3
[48998.553279] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[48998.553983] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[48999.672645] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49006.433766] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49007.553001] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49014.324065] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49015.443420] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49017.114198] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49020.504988] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49020.505232] 8021q: adding VLAN 0 to HW filter on device eth3
[49027.384727] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49027.385427] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49028.514176] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49035.185152] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49036.314505] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49041.715499] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49056.937464] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49056.937711] 8021q: adding VLAN 0 to HW filter on device eth3
[49059.866382] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49059.867084] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49060.995761] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49067.676774] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49068.796147] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49075.517189] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49076.646564] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49078.317329] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49081.708241] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49081.708499] 8021q: adding VLAN 0 to HW filter on device eth3
[49088.577882] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49088.578584] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49089.707211] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49096.378251] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49097.507567] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49102.908564] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49118.110582] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49118.110828] 8021q: adding VLAN 0 to HW filter on device eth3
[49121.129487] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49121.130188] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49122.258940] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49128.939906] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49130.059256] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49136.730373] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49137.859656] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49139.490395] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49142.923916] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49142.924161] 8021q: adding VLAN 0 to HW filter on device eth3
[49149.630939] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49149.631646] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49150.760332] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49157.431304] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49158.560690] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49163.971680] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49179.194080] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49179.194325] 8021q: adding VLAN 0 to HW filter on device eth3
[49182.162633] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49182.163332] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49183.282109] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49190.133009] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49191.252361] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49198.493392] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49199.622776] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49201.243523] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49204.686090] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49204.686332] 8021q: adding VLAN 0 to HW filter on device eth3
[49211.414051] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49211.414752] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49212.543499] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49219.214431] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49220.343802] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49225.744757] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49240.956814] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49240.957057] 8021q: adding VLAN 0 to HW filter on device eth3
[49243.925719] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49243.926466] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49245.045157] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49251.896078] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49253.015432] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49259.866478] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49260.985897] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49262.676636] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49266.050325] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49266.050568] 8021q: adding VLAN 0 to HW filter on device eth3
[49272.947142] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49272.947841] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49274.076582] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49280.757561] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49281.876905] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49287.257929] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49302.470012] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49302.470259] 8021q: adding VLAN 0 to HW filter on device eth3
[49305.398779] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49305.399482] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49306.518162] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49313.189196] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49314.318513] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49320.999526] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49322.118927] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49323.769710] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49327.183844] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49327.184087] 8021q: adding VLAN 0 to HW filter on device eth3
[49333.910211] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49333.910907] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49335.039532] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49341.880653] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49343.009943] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49348.390898] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49363.614614] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49363.614861] 8021q: adding VLAN 0 to HW filter on device eth3
[49366.551869] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49366.552572] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49367.671159] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49374.352160] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49375.471558] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49382.152582] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49383.282030] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49384.912711] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49388.344229] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49388.344473] 8021q: adding VLAN 0 to HW filter on device eth3
[49395.093215] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49395.093913] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49396.212570] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49402.973644] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49404.102958] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49409.543919] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49424.766265] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49424.766509] 8021q: adding VLAN 0 to HW filter on device eth3
[49427.684865] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49427.685567] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49428.804276] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49435.505237] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49436.634557] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49443.305780] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49444.435049] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49446.065814] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49449.496693] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49449.496938] 8021q: adding VLAN 0 to HW filter on device eth3
[49456.226231] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49456.226930] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49457.345685] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49464.026610] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49465.145951] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49470.536926] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49485.759067] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49485.759311] 8021q: adding VLAN 0 to HW filter on device eth3
[49488.687837] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49488.688537] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49489.817203] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49496.488217] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49497.617584] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49504.288605] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49505.418000] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49507.048753] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49510.479628] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49510.479871] 8021q: adding VLAN 0 to HW filter on device eth3
[49517.189312] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49517.190019] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49518.318598] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49524.989646] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49526.118987] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49531.519933] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49546.742363] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49546.742608] 8021q: adding VLAN 0 to HW filter on device eth3
[49549.700825] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49549.701646] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49550.820195] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49557.501249] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49558.620573] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49565.301842] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49566.420937] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49568.041718] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49571.488297] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49571.488540] 8021q: adding VLAN 0 to HW filter on device eth3
[49578.202201] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49578.202902] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49579.321610] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49586.002608] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49587.121933] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49592.532922] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49607.773684] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49607.773926] 8021q: adding VLAN 0 to HW filter on device eth3
[49610.833810] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49610.834504] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49611.963192] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49618.704235] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49619.823529] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49626.494663] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49627.623949] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49629.234713] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49632.685683] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49632.685926] 8021q: adding VLAN 0 to HW filter on device eth3
[49639.395283] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49639.395984] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49640.524559] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49647.195597] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49648.324967] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49653.725920] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49668.947849] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49668.948092] 8021q: adding VLAN 0 to HW filter on device eth3
[49671.906786] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49671.907484] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49673.026248] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49679.707177] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49680.826546] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49687.507588] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49688.626878] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49690.247668] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49693.689126] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49693.689369] 8021q: adding VLAN 0 to HW filter on device eth3
[49700.388122] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49700.388820] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49701.507554] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49708.268521] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49709.397899] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49714.818927] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49730.030775] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49730.031022] 8021q: adding VLAN 0 to HW filter on device eth3
[49732.959736] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49732.960435] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49734.079096] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49740.750086] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49741.879466] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49748.560496] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49749.679842] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49751.330646] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49754.744922] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49754.745165] 8021q: adding VLAN 0 to HW filter on device eth3
[49761.471100] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49761.471798] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49762.600452] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49769.361524] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49770.480846] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49776.031843] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49791.263732] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49791.263974] 8021q: adding VLAN 0 to HW filter on device eth3
[49794.232681] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49794.233378] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49795.362060] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49802.123095] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49803.242445] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49810.003459] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49811.132811] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49812.803587] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49816.197006] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49816.197251] 8021q: adding VLAN 0 to HW filter on device eth3
[49822.934076] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49822.934776] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49824.053418] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49830.724423] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49831.853817] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49837.244747] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49852.456911] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49852.457156] 8021q: adding VLAN 0 to HW filter on device eth3
[49855.415619] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49855.416316] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49856.534969] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49863.205957] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49864.335386] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49871.016347] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49872.135696] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49873.756477] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49877.199508] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49877.199751] 8021q: adding VLAN 0 to HW filter on device eth3
[49883.906991] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49883.907690] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49885.036352] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49891.717418] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49892.836698] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49898.247727] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49913.499619] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49913.499867] 8021q: adding VLAN 0 to HW filter on device eth3
[49916.418505] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49916.419230] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49917.547866] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49924.218982] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49925.348324] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49932.019336] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49933.148602] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49934.799388] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49938.212067] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49938.212311] 8021q: adding VLAN 0 to HW filter on device eth3
[49944.939870] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49944.940569] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49946.069238] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49952.760209] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49953.889604] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49959.340557] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49974.562437] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49974.562686] 8021q: adding VLAN 0 to HW filter on device eth3
[49977.511418] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49977.512123] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[49978.630848] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49985.311852] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49986.441179] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49993.112126] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[49994.241601] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[49995.862369] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[49999.303060] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[49999.303307] 8021q: adding VLAN 0 to HW filter on device eth3
[50006.032800] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50006.033499] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50007.162123] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50013.913096] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50015.042588] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50020.433476] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50035.644204] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50035.644457] 8021q: adding VLAN 0 to HW filter on device eth3
[50038.704331] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50038.705034] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50039.833747] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50046.554661] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50047.674031] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50054.355075] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50055.474491] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50057.105195] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50060.535897] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50060.536140] 8021q: adding VLAN 0 to HW filter on device eth3
[50067.225666] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50067.226365] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50068.355022] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50075.026014] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50076.155375] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50081.576314] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50096.798235] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50096.798484] 8021q: adding VLAN 0 to HW filter on device eth3
[50099.717171] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50099.717874] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50100.846567] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50107.807567] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50108.936943] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50115.567936] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50116.697288] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50118.348016] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50121.761273] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50121.761519] 8021q: adding VLAN 0 to HW filter on device eth3
[50128.508519] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50128.509222] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50129.637888] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50136.398876] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50137.518245] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50143.129288] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50158.364234] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50158.364480] 8021q: adding VLAN 0 to HW filter on device eth3
[50161.310036] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50161.310738] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50162.439413] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50169.410421] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50170.529827] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50177.250804] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50178.380239] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50179.990955] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50183.441657] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50183.441902] 8021q: adding VLAN 0 to HW filter on device eth3
[50190.171416] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50190.173932] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50191.290790] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50198.051790] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50199.181184] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50204.572039] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50219.784171] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50219.784423] 8021q: adding VLAN 0 to HW filter on device eth3
[50222.712992] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50222.713695] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50223.842388] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50230.543317] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50231.662744] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50238.343721] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50239.463032] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50241.083771] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50244.524612] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50244.524857] 8021q: adding VLAN 0 to HW filter on device eth3
[50251.494260] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50251.494962] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50252.613597] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50259.274630] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50260.404004] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50265.825022] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50281.045033] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50281.045277] 8021q: adding VLAN 0 to HW filter on device eth3
[50283.995843] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50283.996548] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50285.125148] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50291.776122] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50292.905562] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50299.586463] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50300.705874] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50302.336625] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50305.767384] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50305.767630] 8021q: adding VLAN 0 to HW filter on device eth3
[50312.477107] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50312.477809] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50313.606432] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50320.312040] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50321.406783] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50326.807736] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50342.008897] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50342.009144] 8021q: adding VLAN 0 to HW filter on device eth3
[50344.968588] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50344.969288] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50346.088014] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50353.038982] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50354.168310] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50360.909310] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50362.028686] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50363.639436] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50367.093166] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50367.093409] 8021q: adding VLAN 0 to HW filter on device eth3
[50373.809983] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50373.810684] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50374.929263] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50381.630278] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50382.749641] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50388.140576] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50403.361677] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50403.361924] 8021q: adding VLAN 0 to HW filter on device eth3
[50406.311431] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50406.312132] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50407.430793] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50414.111760] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50415.231150] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50421.912098] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50423.041567] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50424.652224] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50428.106397] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50428.106642] 8021q: adding VLAN 0 to HW filter on device eth3
[50434.852984] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50434.853669] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50435.982094] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50442.743110] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50443.862481] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50449.303353] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50464.525083] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50464.525327] 8021q: adding VLAN 0 to HW filter on device eth3
[50467.454202] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50467.454902] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50468.563559] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50475.244569] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50476.373916] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50483.044991] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50484.174310] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50485.825045] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50489.237921] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50489.238164] 8021q: adding VLAN 0 to HW filter on device eth3
[50495.965517] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50495.966219] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50497.094989] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50503.875872] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50504.995308] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50510.586613] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50525.777727] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50525.777972] 8021q: adding VLAN 0 to HW filter on device eth3
[50528.696992] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50528.697695] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50529.826454] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50536.507352] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50537.626786] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50544.307733] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50545.437149] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50547.077830] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50550.498738] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50550.498981] 8021q: adding VLAN 0 to HW filter on device eth3
[50557.208301] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50557.209005] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50558.327658] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50565.008662] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50566.128036] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50571.529024] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50586.750529] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50586.750773] 8021q: adding VLAN 0 to HW filter on device eth3
[50589.799764] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50589.800461] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50590.919221] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50597.550142] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50598.679453] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50605.480483] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50606.609905] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50608.210590] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50611.671485] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50611.671729] 8021q: adding VLAN 0 to HW filter on device eth3
[50618.381074] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50618.381767] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50619.510460] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50626.181447] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50627.310781] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50632.711727] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50647.893912] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50647.894159] 8021q: adding VLAN 0 to HW filter on device eth3
[50650.862599] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50650.863435] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50651.991905] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50659.132907] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50660.252366] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50666.933266] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50668.052663] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50669.683473] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50673.116390] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50673.116633] 8021q: adding VLAN 0 to HW filter on device eth3
[50679.823869] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50679.824567] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50680.953231] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50687.634184] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50688.753522] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50694.164488] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50709.376620] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50709.376868] 8021q: adding VLAN 0 to HW filter on device eth3
[50712.315342] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50712.316040] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50713.444658] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50720.095685] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50721.224999] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50727.896039] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50729.025350] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50730.676100] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50734.089275] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50734.089523] 8021q: adding VLAN 0 to HW filter on device eth3
[50740.966628] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50740.967336] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50742.085952] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50748.766987] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50749.886314] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50755.287250] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50770.498658] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50770.498901] 8021q: adding VLAN 0 to HW filter on device eth3
[50773.468046] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50773.468747] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50774.597402] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50781.358400] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50782.477769] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50789.238744] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50790.368180] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50792.038965] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50795.432482] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50795.432728] 8021q: adding VLAN 0 to HW filter on device eth3
[50802.159418] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50802.160120] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50803.288701] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50809.959781] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50811.089057] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50816.479967] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50831.701402] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50831.701648] 8021q: adding VLAN 0 to HW filter on device eth3
[50834.670792] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50834.671502] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50835.790145] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50842.711167] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50843.820486] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50850.611556] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50851.730861] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50853.421653] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50856.792466] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50856.792714] 8021q: adding VLAN 0 to HW filter on device eth3
[50863.512066] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50863.512765] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50864.631474] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50871.312433] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50872.431790] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50877.832728] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50893.034202] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50893.034454] 8021q: adding VLAN 0 to HW filter on device eth3
[50895.993551] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50895.994252] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50897.112872] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50903.793861] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50904.913226] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50911.594209] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50912.713606] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50914.334370] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[50917.775176] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[50917.775421] 8021q: adding VLAN 0 to HW filter on device eth3
[50924.464767] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50924.465469] IPv6: ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[50925.594129] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50932.275168] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[50933.394574] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Down
[50938.815437] igb 0000:13:00.0 eth3: igb: eth3 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX

jwj***

装4个op，三条线路3个op各自多拨，然后进第四个op。。。。。。我乱说的

cc***

jwj200 发表于 2016-10-17 16:39
装4个op，三条线路3个op各自多拨，然后进第四个op。。。。。。我乱说的

你的这个思路我已经达成了，但是这样会造成我软路由效能的降低，跑不满带宽
所以我想用一个op来实现的

gavi***

建议换ros吧。用vrrp创建虚拟接口……

cc***

gavin219 发表于 2016-10-17 20:15
建议换ros吧。用vrrp创建虚拟接口……

多谢回复。。。ros不熟悉的说

dang***

只有多虚拟出来几个OP了，我的ESXI里面虚拟了7个，6个负责多播，1个负责叠加

cc***

dangyixin 发表于 2016-10-18 13:08
只有多虚拟出来几个OP了，我的ESXI里面虚拟了7个，6个负责多播，1个负责叠加

你这个方法是最传统的方法，这种办法我已经搞定了，想换一个

dang***

ccds 发表于 2016-10-18 14:11
你这个方法是最传统的方法，这种办法我已经搞定了，想换一个

关键还是看你多拨需不需要并发，如果不需要并发单个op完全可以搞定

cc***

dangyixin 发表于 2016-10-18 20:01
关键还是看你多拨需不需要并发，如果不需要并发单个op完全可以搞定

对头，关键是3条线都需要并发

vinso***

楼主找到解决办法了吗？

cc***

vinsonyang 发表于 2016-10-24 15:48
楼主找到解决办法了吗？

找到解决办法了，就是设置好单线多拨以后，手动改/etc/config/network配置文件

vinso***

ccds 发表于 2016-10-24 22:33
找到解决办法了，就是设置好单线多拨以后，手动改/etc/config/network配置文件

能详细的说明一下吗？谢谢