网件 4500V2 故障求解决

鲁***

网件 4500V2 绿灯闪烁，官网给的解答是丢失固件，需要TFTP刷固件。
TFTP刷了固件后，电源黄灯闪烁，无限重启，

在用USB转TTL，中断在CFE下面，通过TFTP刷固件不会自动重启。重启后电源绿灯就开始闪烁了。这个时候TTL现实TFTP SERVER启动，在等待刷机。
无限循环，求解答。

刷TOMATO BA SHIFFY 成功，想刷回官网怎么弄。直接刷就进入CFE模式了。

nazc***

先刷官网的固件不行的话试试刷openwrt。我在用4300V1。128M flash刷机不方便，还是16M的好刷

鲁***

我马上刷TOMATO试试，谁有网件 4500V2 CFE 文件，发一个给我。  TOMATO  网件4500V2  怎么刷回官方固件，有人知道吗？好像TOMATO会改变CFE.

鲁***

CFE for WNDR4500 version: v1.0.6
Build Date: Thu Aug 21 09:22:55 CST 2014
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Mxic NAND flash with 2048B pages or 128KB blocks; total size 128MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes

Device eth0:  hwaddr A4-2B-8C-94-6A-C6, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Checking crc...Loader:raw Filesys:raw Dev:nflash0.os File: Optionsnull)
Loading: ....... 4239494 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22 (builder@production) (gcc version 4.2.3) #223 PREEMPT Tue Jan 10 21:16:05 CST 2017
CPU revision is: 00019749
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal          0 ->    32767
  HighMem     32767 ->    32767
early_node_map[1] active PFN ranges
    0:        0 ->    32767
Built 1 zonelists.  Total pages: 32767
Kernel command line: root=/dev/mtdblock16 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5300 rev 1 at 600 MHz
Using 300.000 MHz high precision timer.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 125084k/131068k available (3243k kernel code, 5836k reserved, 664k data, 232k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
pflash: found no supported devices
sflash: Couldn't find valid ROM disk image
Creating 15 MTD partitions on "sflash":
0x00000000-0x00200000 : "boot"
0x00000000-0x00140000 : "linux"
0x00000000-0x00200000 : "rootfs"
0x00140000-0x00150000 : "ML1"
0x00150000-0x00160000 : "ML2"
0x00160000-0x00170000 : "ML3"
0x00170000-0x00180000 : "ML4"
0x00180000-0x00190000 : "ML5"
0x00190000-0x001a0000 : "ML6"
0x001a0000-0x001b0000 : "ML7"
0x001b0000-0x001c0000 : "T_Meter1"
0x001c0000-0x001d0000 : "T_Meter2"
0x001d0000-0x001e0000 : "OT"
0x001e0000-0x001f0000 : "board_data"
0x001f0000-0x00200000 : "nvram"
Found a Mxic NAND flash with 2048B pages or 128KB blocks; total size 128MB
lookup_nflash_rootfs_offset: offset = 0x0
nflash: squash filesystem with lzma found at block 11
Creating 2 MTD partitions on "nflash":
0x00000000-0x02000000 : "linux"
0x00160764-0x02000000 : "rootfs"
NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Mxic NAND 128MiB 3,3V 8-bit)
Creating 2 MTD partitions on "brcmnand":
0x00000000-0x02000000 : "trx"
0x02000000-0x07f00000 : "brcmnand"
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
u32 classifier
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 232k freed
Warning: unable to open an initial console.
Failed to execute /init
[sighandler]: No more events to be processed, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
Reading board data...
WSC UUID: 0xd9077417e4b5b66732fd933b6ba4cf51
NTP synchronized date/time: Wed Jun 10 21:43:44 2015
MAC address of 1st STA connected: F0-24-75-60-4C-9E
invalid RF magic!
No RF parameters! Use default.
### main:1091 Set Normal Power!
Initialise conn table 2048 entries
insmod: usbcore.ko: no module by that name found
insmod: wl_high.ko: no module by that name found
eth3: cmd=14: No such device
wl1 not up in 3 sec
Hit enter to continue...killall: upnp: no process killed
upnp: No such file or directory
WARNING: console log level set to 1
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x100b
Reading board data...
WSC UUID: 0xd9077417e4b5b66732fd933b6ba4cf51
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acosFW_accessCtrlEnable 2684 bEnable: 0
acosFW_accessCtrlMode 2691 mode: 1
acosFW_accessCtrlConfig 2698
acsd: scan in progress ...
killall: udhcpd: no process killed
acsd: selected channel spec: 0x100b
info, udhcp server (v0.9.8) started
error, unable to parse 'option wins '
error, unable to parse 'option domain '
mevent start...
opened loopback socket 4
POT integrity check OK.
POT time is up.
ACSD >>acsd_svr_socket_init(82): Socket bind failed: Address already in use
Can't find handler for ASP command: eco_get_redirect_link();
Can't find handler for ASP command: cdl_cgi_set_hijack(0);
Can't find handler for ASP command: cdl_cgi_set_hijack(1);
insmod: usbcore.ko: no module by that name found
insmod: cannot insert '/lib/modules/2.6.22/kernel/drivers/usb/host/ehci-hcd.ko': Success (17)
insmod: GPL_NetUSB.ko: no module by that name found
mount: mounting none on /proc/bus/usb failed: Device or resource busy
IOCTL_AG_REGION_SET: English
Start DHCP client daemon
info, udhcp client (v0.9.8) started
eth0: No such process
Info: No FWPT default policies.
agnat QOS disable!
rmmod: l7_filter
ioctl(BRCTL_SET_BCMCTF_ENABLE): Operation not supported
ioctl(BRCTL_SET_BCMCTF_ENABLE): Operation not supported
rmmod: /lib/modules/2.6.22/kernel/lib/AccessCntl.ko
route: ioctl 0x890c failed: No such process
killall: dhcp6c: no process killed
killall: IPv6-relay: no process killed
killall: pppdv6: no process killed
killall: rtsol: no process killed
killall: dhcp6s: no process killed
killall: radvd: no process killed
[AFP]: 0 partitions found.
[AFP]: disk mountd:0  hfsplus mounted:0
[AFP]: no disk mounted.
ifconfig: invalid number ''
ifconfig: invalid number ''
route: ioctl 0x890c failed: No such process
killall: dhcp6s: no process killed
killall: radvd: no process killed
Hit enter to continue...Hit enter to continue...Hit enter to continue...killall: bftpd: no process killed
Hit enter to continue...httpd: socket bound in 0.0.0.0:80.
httpd: socket bound in 0.0.0.0:443.
Decompressing...done
进入官方系统 10秒左右会自动重启，刷了TOMOTO,正常使用，有大神来看看是不是NAND FLASH损坏