小豹AI音箱（智障）TTL启动跑码信息

pri***

这玩意有otg口，ttl找到以后也许可以通过u盘刷入armbian linux 大概率声卡无法驱动。（maskroom短接点没找到）

DDR Version V1.06 20171026
In
300MHz
DDR3
Bus Width=16 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=512MB
mach:9
OUT
Boot1 Release Time: 2016-08-29, version: 2.32
ChipType = c 297
...SdmmcInit enter...
SdmmcInit=2 0
BootCapSize=1000
UserCapSize=760000
FwPartOffset=2000 , 1000
...SdmmcInit enter...
SdmmcInit=0 20
StorageInit ok = 72830
SecureMode : SBOOT_MODE_NS
Loder code check ok! theLoader 0x60000000, loadaddr: 0x2000
Loder code check ok! theLoader 0x68400000, loadaddr: 0x4000
...Enter Trust OS: 0x68400000
INF TEE-CORE:init_primary_helper:319: Initializing (1.0.1-54-g0d46013 #4 Thu Sep 29 01:09:49 UTC 2016 arm)
INF TEE-CORE:init_primary_helper:320: Release version: 1.6
INF TEE-CORE:init_teecore:79: teecore inits done


[hide=d720]U-Boot 2014.10-RK322X-06 (Mar 20 2019 - 17:57:16)

CPU: rk322x
cpu version = 3
CPU's clock information:
    arm pll = 600000000HZ
    periph pll = 600000000HZ
    ddr pll = 600000000HZ
    codec pll = 500000000HZ
Board:  Rockchip platform Board
Uboot as second level loader
DRAM:  Found dram banks: 1
Adding bank:0000000060000000(0000000020000000)
Reserve memory for trust os.
dram reserve bank: base = 0x68400000, size = 0x00100000
128 MiB
arch_early_init_r
GIC CPU mask = 0x00000001
rk dma pl330 version: 1.4
remotectl v0.1
pwm freq=0x11e1a3
pwm_freq_nstime=0x355
SdmmcInit = 0 20
SdmmcInit = 2 0
ERROR: v7_dcache_inval_range - start address is not aligned - 0x659bc2cc
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x659bc4cc
storage init OK!
Using default environment

board_late_init
getenv: bootdelay = 0
getenv: bootcmd = bootrk
getenv: initrd_high = 0xffffffff=n
GetParam
rkimage_prepare_fdt
Load FDT from boot image.
key_init
pmic_init
pmic:rk805
pwm_regulator_init
DCDC vdd_arm has been used, pwm regulator not init it.
DCDC vdd_logic has been used, pwm regulator not init it.
fg_init
DRAM: dram freq:786MHz
idb init
SecureBootEn = 0, SecureBootLock = 0

#Boot ver: 2018-05-05#2.32
sn: 032203820006777|105260229|gfcONd4YK6jp3cRQ
fbt preboot
~~~~~~~~~~~~init_leds i2c_probe error
normal boot.
ERROR: [board_fbt_preboot]:
board_fbt_preboot: no spec reboot type, check key press.
checkKey
vbus = 0
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
no fuel gauge found
no fuel gauge found
can't find power_ctr node for lcdc0
HDMI: no pull up gpio
can't find dts node for deviceinfo
rk_hdmi_register:fail to read deviceinfo
hdmi baseparamer 0x0@0-0
tve baseparamer 0x0@0-0
Hdmi Devices Not Exist.
can't find dts node for rk312x-tve
SCREEN_TVOUT
rk3036_tve_init:use default config g_tve_pos = 1
read logo on state from dts [1]
no fuel gauge found
checkKey
vbus = 0
board_fbt_key_pressed: ir_keycode = 0x0, frt = 0
ERROR: [board_fbt_preboot]:
board_fbt_preboot: check misc command.
Hit any key to stop autoboot:  0
## Current stack ends at 0x6571f648 Secure Boot state: 0
kernel   @ 0x62000000 (0x0070ba90)
ramdisk  @ 0x65bf0000 (0x0016c544)
bootrk: do_bootm_linux...
   Loading Device Tree to 65600000, end 65615878 ... OK
Add bank:0000000060000000, 0000000008400000
Add bank:0000000068500000, 0000000017b00000

Starting kernel ...

taiz***

感谢分享，谢谢楼主，加油感谢分享，谢谢楼主，加油

书到用***

小豹AI音箱的刷机教程哪里有？