|
|
breed信息如下：
CPU | MediaTek MT7621A ver 1, eco 3 | 内存 | 128MB DDR3 | Flash | Macronix MX25L12835E @ 44MHz (16MB) | 以太网 | MediaTek MT7530 Gigabit switch | 时钟频率 | CPU: 880MHz, DDR: 1040MHz, Bus: 220MHz, Ref: 40MHz | 编译日期 | 2021-12-15 [git-f9b74d0] | 版本 | 1.1 (r1337) |
有没有好心人帮我看看怎么回事？
启动日志如下：
breed> autoboot
Trying to boot firmware from 0x00050000 in flash bank 0 ...
Reading data into memory ...
U-Boot firmware image header detected.
Image Name: MIPS OpenWrt Linux-3.10.108
Data Size: 2815941 Bytes
Load Address: 81001000
Entry Point: 81001000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.
Starting kernel at 0x81001000...
LINUX started...
THIS IS ASIC
SDK 5.0.S.0
[ 0.000000] Linux version 3.10.108 (ngcf@compiler53) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r10278) ) #1 SMP Fri Oct 29 09:05:55 CST 2021
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 880 MHz
[ 0.000000] GCMP present
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] MIPS: machine is EW1200G PRO
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Detected 3 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @818a4000 s6080 r8192 d14400 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock6 mtdparts=raspi:320k(u-boot)ro,64k(u-boot-env),64k(Factory),64k(product_info),64k(kdump),-(firmware) rootfstype=squashfs,jffs2 print-fatal-signals=1
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00056020
[ 0.000000] Readback ErrCtl register=00056020
[ 0.000000] Memory: 122000k/131072k available (5323k kernel code, 9072k reserved, 1922k data, 236k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.124000] Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
[ 0.164000] pid_max: default: 32768 minimum: 301
[ 0.168000] Mount-cache hash table entries: 512
[ 0.172000] launch: starting cpu1
[ 0.176000] launch: cpu1 gone!
[ 0.176000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.176000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.176000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.176000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.208000] Synchronize counters for CPU 1: done.
[ 0.212000] launch: starting cpu2
[ 0.216000] launch: cpu2 gone!
[ 0.216000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.216000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.216000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.216000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.248000] Synchronize counters for CPU 2: done.
[ 0.252000] launch: starting cpu3
[ 0.256000] launch: cpu3 gone!
[ 0.256000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.256000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.256000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.256000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.284000] Synchronize counters for CPU 3: done.
[ 0.288000] Brought up 4 CPUs
[ 0.292000] NET: Registered protocol family 16
[ 0.600000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.612000] PCIE PHY initialize
[ 0.616000] ***** Xtal 40MHz *****
[ 0.624000] start MT7621 PCIe register access
[ 1.224000] RALINK_RSTCTRL = 7000000
[ 1.232000] RALINK_CLKCFG1 = 77ffeff8
[ 1.240000]
[ 1.240000] *************** MT7621 PCIe RC mode *************
[ 1.748000] PCIE1 no card, disable it(RST&CLK)
[ 1.756000] PCIE2 no card, disable it(RST&CLK)
[ 1.764000] pcie_link status = 0x1
[ 1.772000] RALINK_RSTCTRL= 1000000
[ 1.780000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[ 1.792000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
[ 1.804000] PCIE0 enabled
[ 1.808000] interrupt enable status: 100000
[ 1.816000] Port 0 N_FTS = 1b105000
[ 1.824000] config reg done
[ 1.828000] init_rt2880pci done
[ 1.836000] gpio device register!
[ 1.848000] bio: create slab <bio-0> at 0
[ 1.852000] ralink_gpio ralink_gpio.0: registering 32 gpios
[ 1.856000] ralink_gpio ralink_gpio.0: registering 32 gpios
[ 1.860000] ralink_gpio ralink_gpio.0: registering 32 gpios
[ 1.864000] PCI host bridge to bus 0000:00
[ 1.868000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.872000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.876000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.880000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.884000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.888000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60100000-0x6010ffff]
[ 1.892000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 1.896000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.900000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.904000] BAR0 at slot 0 = 0
[ 1.908000] bus=0x0, slot = 0x0
[ 1.912000] res[0]->start = 0
[ 1.916000] res[0]->end = 0
[ 1.920000] res[1]->start = 60100000
[ 1.924000] res[1]->end = 6010ffff
[ 1.928000] res[2]->start = 0
[ 1.932000] res[2]->end = 0
[ 1.936000] res[3]->start = 0
[ 1.940000] res[3]->end = 0
[ 1.944000] res[4]->start = 0
[ 1.948000] res[4]->end = 0
[ 1.952000] res[5]->start = 0
[ 1.956000] res[5]->end = 0
[ 1.960000] bus=0x1, slot = 0x0, irq=0x4
[ 1.964000] res[0]->start = 60000000
[ 1.968000] res[0]->end = 600fffff
[ 1.972000] res[1]->start = 0
[ 1.976000] res[1]->end = 0
[ 1.980000] res[2]->start = 0
[ 1.984000] res[2]->end = 0
[ 1.988000] res[3]->start = 0
[ 1.992000] res[3]->end = 0
[ 1.996000] res[4]->start = 0
[ 2.000000] res[4]->end = 0
[ 2.004000] res[5]->start = 0
[ 2.008000] res[5]->end = 0
[ 2.012000] proc fast_bridge create start
[ 2.016000] proc fast_bridge create successful
[ 2.020000] Switching to clocksource Ralink Systick timer
[ 2.024000] NET: Registered protocol family 2
[ 2.028000] Clockevents: could not switch to one-shot mode:
[ 2.028000] Clockevents: could not switch to one-shot mode:
[ 2.028000] MIPS is not functional.
[ 2.028000] MIPS is not functional.
[ 2.028000] Clockevents: could not switch to one-shot mode: MIPS is not functional.
[ 2.028000] Could not switch to high resolution mode on CPU 1
[ 2.028000] Could not switch to high resolution mode on CPU 0
[ 2.028000] Could not switch to high resolution mode on CPU 3
[ 2.120000] Clockevents: could not switch to one-shot mode: MIPS is not functional.
[ 2.136000] Could not switch to high resolution mode on CPU 2
[ 2.148000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 2.160000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 2.172000] TCP: Hash tables configured (established 1024 bind 1024)
[ 2.188000] TCP: reno registered
[ 2.192000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.204000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.216000] NET: Registered protocol family 1
[ 2.228000] Load Kernel WDG Timer Module
[ 2.236000] Load Ralink Timer0 Module
[ 2.240000] Load Ralink Timer2 Module
[ 2.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.264000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.284000] msgmni has been set to 238
[ 2.292000] io scheduler noop registered (default)
[ 2.300000] reg_int_mask=0, INT_MASK= 0
[ 2.308000] HSDMA_init
[ 2.312000]
[ 2.312000] hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000
[ 2.332000]
[ 2.332000] hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000
[ 2.348000] TX_CTX_IDX0 = 0
[ 2.352000] TX_DTX_IDX0 = 0
[ 2.360000] RX_CRX_IDX0 = 3ff
[ 2.364000] RX_DRX_IDX0 = 0
[ 2.368000] set_fe_HSDMA_glo_cfg
[ 2.376000] HSDMA_GLO_CFG = 465
[ 2.388000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 2.400000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
[ 2.416000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
[ 2.428000] Ralink gpio driver initialized
[ 2.436000] Enable Ralink GDMA Controller Module
[ 2.448000] GDMA IP Version=3
[ 2.452000] flash manufacture id: c2, device id 20 18
[ 2.464000] MX25L12805D(c2 2018c220) (16384 Kbytes)
[ 2.472000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[ 2.492000] 6 cmdlinepart partitions found on MTD device raspi
[ 2.504000] Creating 6 MTD partitions on "raspi":
[ 2.512000] 0x000000000000-0x000000050000 : "u-boot"
[ 2.524000] 0x000000050000-0x000000060000 : "u-boot-env"
[ 2.536000] 0x000000060000-0x000000070000 : "Factory"
[ 2.548000] 0x000000070000-0x000000080000 : "product_info"
[ 2.560000] 0x000000080000-0x000000090000 : "kdump"
[ 2.572000] 0x000000090000-0x000001000000 : "firmware"
[ 2.584000] register mt_drv
[ 2.612000]
[ 2.612000] == pAd = c0181000, size = 7918720, Status=0 ==
[ 2.628000] pAd->PciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
[ 2.640000] RTMPInitPCIeDevice():device_id=0x7615
[ 2.648000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615
[ 2.664000] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001
[ 2.672000] AP Driver version-5.0.4.0
[ 2.680000] RtmpChipOpsHook(223): Not support for HIF_MT yet! MACVersion=0x0
[ 2.696000] mt7615_init()-->
[ 2.700000] Use the default ePAeLNA bin image!
[ 2.708000] Use the default /etc_ro/wlan/MT7615E_EEPROM1.bin bin image!
[ 2.724000] <--mt7615_init()
[ 2.732000] <-- RTMPAllocTxRxRingMemory, Status=0
[ 2.744000] ------------------hello world !--------------------========STA INIT=============
[ 2.760000] MTK NETLINK SUCCESS!!!!!
[ 2.768000] Netlink NEIGHBOR_DIAGNOSIS Module inserted.
[ 2.776000] Netlink REPDISC Module inserted.
[ 2.788000] Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500!
[ 2.808000] PROC INIT OK!
[ 2.812000] set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
[ 2.836000] net eth0: loaded mt7621 driver
[ 2.844000] Zhanguo debug ra2882eth_init : mt7530_probe successfully.
[ 2.856000] TCP: cubic registered
[ 2.864000] NET: Registered protocol family 10
[ 2.872000] NET: Registered protocol family 17
[ 2.884000] Bridge firewalling registered
[ 2.892000] 8021q: 802.1Q VLAN Support v1.8
[ 2.900000] VFS: Cannot open root device "mtdblock6" or unknown-block(0,0): error -6
[ 2.916000] Please append a correct "root=" boot option; here are the available partitions:
[ 2.932000] 1f00 320 mtdblock0 (driver?)
[ 2.944000] 1f01 64 mtdblock1 (driver?)
[ 2.952000] 1f02 64 mtdblock2 (driver?)
[ 2.964000] 1f03 64 mtdblock3 (driver?)
[ 2.972000] 1f04 64 mtdblock4 (driver?)
[ 2.984000] 1f05 15808 mtdblock5 (driver?)
[ 2.992000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 3.008000] stop feeding watchdog.
[ 3.016000] Rebooting in 3 seconds..wdg reset
[ 15.848000] release spi pin
[ 15.868000] normal reset
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2021 HackPascal <hackpascal@gmail.com>
Build date 2021-12-15 [git-f9b74d0]
Version 1.1 (r1337)
DRAM: 128MB
Platform: MediaTek MT7621A ver 1, eco 3
Board: Netgear WNDR3700 v5
Clocks: CPU: 880MHz, DDR: 1040MHz, Bus: 220MHz, Ref: 40MHz
Flash: Macronix MX25L12835E (16MB) on mt7621-spi.0
rt2880-eth: MAC address from EEPROM is invalid, using default settings.
rt2880-eth: Using MAC address 00:0c:43:00:00:01
eth0: MediaTek MT7530 Gigabit switch
Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Press any key to interrupt autoboot ... 2
Autoboot aborted due to button press.
Starting breed built-in shell
breed> autoboot
Trying to boot firmware from 0x00050000 in flash bank 0 ...
Reading data into memory ...
U-Boot firmware image header detected.
Image Name: MIPS OpenWrt Linux-3.10.108
Data Size: 2815941 Bytes
Load Address: 81001000
Entry Point: 81001000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.
Starting kernel at 0x81001000...
LINUX started...
THIS IS ASIC
SDK 5.0.S.0
[ 0.000000] Linux version 3.10.108 (ngcf@compiler53) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r10278) ) #1 SMP Fri Oct 29 09:05:55 CST 2021
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 880 MHz
[ 0.000000] GCMP present
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] MIPS: machine is EW1200G PRO
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00000000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Detected 3 available secondary CPU(s)
[ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] PERCPU: Embedded 7 pages/cpu @818a4000 s6080 r8192 d14400 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock6 mtdparts=raspi:320k(u-boot)ro,64k(u-boot-env),64k(Factory),64k(product_info),64k(kdump),-(firmware) rootfstype=squashfs,jffs2 print-fatal-signals=1
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00056021
[ 0.000000] Readback ErrCtl register=00056021
[ 0.000000] Memory: 122000k/131072k available (5323k kernel code, 9072k reserved, 1922k data, 236k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.124000] Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
[ 0.164000] pid_max: default: 32768 minimum: 301
[ 0.168000] Mount-cache hash table entries: 512
[ 0.172000] launch: starting cpu1
[ 0.176000] launch: cpu1 gone!
[ 0.176000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.176000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.176000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.176000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.208000] Synchronize counters for CPU 1: done.
[ 0.212000] launch: starting cpu2
[ 0.216000] launch: cpu2 gone!
[ 0.216000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.216000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.216000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.216000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.248000] Synchronize counters for CPU 2: done.
[ 0.252000] launch: starting cpu3
[ 0.256000] launch: cpu3 gone!
[ 0.256000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[ 0.256000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.256000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.256000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.284000] Synchronize counters for CPU 3: done.
[ 0.288000] Brought up 4 CPUs
[ 0.292000] NET: Registered protocol family 16
[ 0.600000] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.612000] PCIE PHY initialize
[ 0.616000] ***** Xtal 40MHz *****
[ 0.624000] start MT7621 PCIe register access
[ 1.224000] RALINK_RSTCTRL = 7000000
[ 1.232000] RALINK_CLKCFG1 = 77ffeff8
[ 1.240000]
[ 1.240000] *************** MT7621 PCIe RC mode *************
[ 1.748000] PCIE1 no card, disable it(RST&CLK)
[ 1.756000] PCIE2 no card, disable it(RST&CLK)
[ 1.764000] pcie_link status = 0x1
[ 1.772000] RALINK_RSTCTRL= 1000000
[ 1.780000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[ 1.792000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
[ 1.804000] PCIE0 enabled
[ 1.808000] interrupt enable status: 100000
[ 1.816000] Port 0 N_FTS = 1b105000
[ 1.824000] config reg done
[ 1.828000] init_rt2880pci done
[ 1.836000] gpio device register!
[ 1.848000] bio: create slab <bio-0> at 0
[ 1.852000] ralink_gpio ralink_gpio.0: registering 32 gpios
[ 1.856000] ralink_gpio ralink_gpio.0: registering 32 gpios
[ 1.860000] ralink_gpio ralink_gpio.0: registering 32 gpios
[ 1.864000] PCI host bridge to bus 0000:00
[ 1.868000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.872000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.876000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.880000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[ 1.884000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.888000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60100000-0x6010ffff]
[ 1.892000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 1.896000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.900000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.904000] BAR0 at slot 0 = 0
[ 1.908000] bus=0x0, slot = 0x0
[ 1.912000] res[0]->start = 0
[ 1.916000] res[0]->end = 0
[ 1.920000] res[1]->start = 60100000
[ 1.924000] res[1]->end = 6010ffff
[ 1.928000] res[2]->start = 0
[ 1.932000] res[2]->end = 0
[ 1.936000] res[3]->start = 0
[ 1.940000] res[3]->end = 0
[ 1.944000] res[4]->start = 0
[ 1.948000] res[4]->end = 0
[ 1.952000] res[5]->start = 0
[ 1.956000] res[5]->end = 0
[ 1.960000] bus=0x1, slot = 0x0, irq=0x4
[ 1.964000] res[0]->start = 60000000
[ 1.968000] res[0]->end = 600fffff
[ 1.972000] res[1]->start = 0
[ 1.976000] res[1]->end = 0
[ 1.980000] res[2]->start = 0
[ 1.984000] res[2]->end = 0
[ 1.988000] res[3]->start = 0
[ 1.992000] res[3]->end = 0
[ 1.996000] res[4]->start = 0
[ 2.000000] res[4]->end = 0
[ 2.004000] res[5]->start = 0
[ 2.008000] res[5]->end = 0
[ 2.012000] proc fast_bridge create start
[ 2.016000] proc fast_bridge create successful
[ 2.020000] Switching to clocksource Ralink Systick timer
[ 2.024000] NET: Registered protocol family 2
[ 2.028000] Clockevents: could not switch to one-shot mode:
[ 2.028000] Clockevents: could not switch to one-shot mode:
[ 2.028000] MIPS is not functional.
[ 2.028000] MIPS is not functional.
[ 2.028000] Clockevents: could not switch to one-shot mode: MIPS is not functional.
[ 2.028000] Could not switch to high resolution mode on CPU 0
[ 2.028000] Could not switch to high resolution mode on CPU 1
[ 2.028000] Could not switch to high resolution mode on CPU 3
[ 2.120000] Clockevents: could not switch to one-shot mode: MIPS is not functional.
[ 2.136000] Could not switch to high resolution mode on CPU 2
[ 2.148000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 2.160000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 2.172000] TCP: Hash tables configured (established 1024 bind 1024)
[ 2.188000] TCP: reno registered
[ 2.192000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.204000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.216000] NET: Registered protocol family 1
[ 2.228000] Load Kernel WDG Timer Module
[ 2.236000] Load Ralink Timer0 Module
[ 2.240000] Load Ralink Timer2 Module
[ 2.252000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.264000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.284000] msgmni has been set to 238
[ 2.292000] io scheduler noop registered (default)
[ 2.300000] reg_int_mask=0, INT_MASK= 0
[ 2.308000] HSDMA_init
[ 2.312000]
[ 2.312000] hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000
[ 2.332000]
[ 2.332000] hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000
[ 2.348000] TX_CTX_IDX0 = 0
[ 2.352000] TX_DTX_IDX0 = 0
[ 2.360000] RX_CRX_IDX0 = 3ff
[ 2.364000] RX_DRX_IDX0 = 0
[ 2.372000] set_fe_HSDMA_glo_cfg
[ 2.376000] HSDMA_GLO_CFG = 465
[ 2.388000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 2.400000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
[ 2.416000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
[ 2.428000] Ralink gpio driver initialized
[ 2.436000] Enable Ralink GDMA Controller Module
[ 2.448000] GDMA IP Version=3
[ 2.452000] flash manufacture id: c2, device id 20 18
[ 2.464000] MX25L12805D(c2 2018c220) (16384 Kbytes)
[ 2.472000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[ 2.492000] 6 cmdlinepart partitions found on MTD device raspi
[ 2.504000] Creating 6 MTD partitions on "raspi":
[ 2.512000] 0x000000000000-0x000000050000 : "u-boot"
[ 2.524000] 0x000000050000-0x000000060000 : "u-boot-env"
[ 2.536000] 0x000000060000-0x000000070000 : "Factory"
[ 2.548000] 0x000000070000-0x000000080000 : "product_info"
[ 2.560000] 0x000000080000-0x000000090000 : "kdump"
[ 2.572000] 0x000000090000-0x000001000000 : "firmware"
[ 2.584000] register mt_drv
[ 2.616000]
[ 2.616000] == pAd = c0181000, size = 7918720, Status=0 ==
[ 2.628000] pAd->PciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
[ 2.640000] RTMPInitPCIeDevice():device_id=0x7615
[ 2.652000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615
[ 2.664000] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001
[ 2.676000] AP Driver version-5.0.4.0
[ 2.684000] RtmpChipOpsHook(223): Not support for HIF_MT yet! MACVersion=0x0
[ 2.696000] mt7615_init()-->
[ 2.704000] Use the default ePAeLNA bin image!
[ 2.712000] Use the default /etc_ro/wlan/MT7615E_EEPROM1.bin bin image!
[ 2.724000] <--mt7615_init()
[ 2.732000] <-- RTMPAllocTxRxRingMemory, Status=0
[ 2.744000] ------------------hello world !--------------------========STA INIT=============
[ 2.760000] MTK NETLINK SUCCESS!!!!!
[ 2.768000] Netlink NEIGHBOR_DIAGNOSIS Module inserted.
[ 2.780000] Netlink REPDISC Module inserted.
[ 2.788000] Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500!
[ 2.808000] PROC INIT OK!
[ 2.816000] set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
[ 2.836000] net eth0: loaded mt7621 driver
[ 2.844000] Zhanguo debug ra2882eth_init : mt7530_probe successfully.
[ 2.856000] TCP: cubic registered
[ 2.864000] NET: Registered protocol family 10
[ 2.876000] NET: Registered protocol family 17
[ 2.884000] Bridge firewalling registered
[ 2.892000] 8021q: 802.1Q VLAN Support v1.8
[ 2.900000] VFS: Cannot open root device "mtdblock6" or unknown-block(0,0): error -6
[ 2.916000] Please append a correct "root=" boot option; here are the available partitions:
[ 2.932000] 1f00 320 mtdblock0 (driver?)
[ 2.944000] 1f01 64 mtdblock1 (driver?)
[ 2.952000] 1f02 64 mtdblock2 (driver?)
[ 2.964000] 1f03 64 mtdblock3 (driver?)
[ 2.976000] 1f04 64 mtdblock4 (driver?)
[ 2.984000] 1f05 15808 mtdblock5 (driver?)
[ 2.996000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 3.012000] stop feeding watchdog.
[ 3.016000] Rebooting in 3 seconds..wdg reset
[ 15.848000] release spi pin
[ 15.868000] normal reset
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2021 HackPascal <hackpascal@gmail.com>
Build date 2021-12-15 [git-f9b74d0]
Version 1.1 (r1337)
DRAM: 128MB
Platform: MediaTek MT7621A ver 1, eco 3
Board: Netgear WNDR3700 v5
Clocks: CPU: 880MHz, DDR: 1040MHz, Bus: 220MHz, Ref: 40MHz
Flash: Macronix MX25L12835E (16MB) on mt7621-spi.0
rt2880-eth: MAC address from EEPROM is invalid, using default settings.
rt2880-eth: Using MAC address 00:0c:43:00:00:01
eth0: MediaTek MT7530 Gigabit switch
Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Press any key to interrupt autoboot ... 4
Autoboot aborted due to key press.
Starting breed built-in shell
breed>
|
|
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡