找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888广告投放联系QQ68610888
查看: 5396|回复: 5

841V7刷了变砖了,求救?

[复制链接]
发表于 2011-4-28 13:43 | 显示全部楼层 |阅读模式
刷了rickyo0的Openwrt 中文语言包和固件https://right.com.cn/forum/thread-47936-1-1.html我的841V7(MW300RV2)变砖了。自动ip地址也不能分配,ping不通和ssh都进不去用TTL是进的去,用tpl不管什么快死活也停不不来。那位好心的讲下有什么办法能刷回来。谢谢!
这是开机信息

U-Boot 1.1.4 (May 28 2010 - 11:12:30)

AP99 (ar7241 - Virian) U-boot
DRAM:
sri
ar7240_ddr_initial_config(133): virian ddr1 init
#### TAP VALUE 1 = 0xf, 2 = 0x10 [0x0: 0x1f]
32 MB
id read 0x100000ff
sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.32.27 (openwrt@openwrt) (gcc version 4.3.3 (GCC) ) #1 Thu Apr 21 18:21:27 CST 2011
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
Atheros AR7241 rev 1, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 board=TL-WR741ND
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29380k/32768k available (2047k kernel code, 3388k reserved, 410k data, 148k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:56
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-WR741ND
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
PCI: fixup device 0000:00:00.0
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: PME# disabled
PCI: mapping irq 48 to pin1@0000:00:00.0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  &#169; 2001-2006 Red Hat, Inc.
yaffs Apr 21 2011 18:16:31 Installing.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: s25sl032a (4096 Kbytes)
Searching for RedBoot partition table in spi0.0 at offset 0x3e0000
Searching for RedBoot partition table in spi0.0 at offset 0x3f0000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=370000, len=80000
0x000000370000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "art"
0x000000020000-0x0000003f0000 : "firmware"
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xba000000, irq 5
eth0: unsupported chip, ctrl=00000000
eth0: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 148k freed
Please be patient, while OpenWrt loads ...
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
- preinit -
Registered led device: tl-wr741nd:green:system
Registered led device: tl-wr741nd:green:qss
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
- init -

Please press Enter to activate this console. device eth0 entered promiscuous mode
Compat-wireless backport release: compat-wireless-2011-03-30-6-g6a250de
Backport based on wireless-testing.git master-2011-04-06
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (461 buckets, 1844 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
xt_time: kernel timezone is -0000
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
发表于 2011-4-28 15:14 | 显示全部楼层
乱提示一下,不知道用安全模式能否进得?就是第一个灯亮时立即拿牙签捅pp
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
发表于 2011-4-28 15:16 | 显示全部楼层
本帖最后由 729650915 于 2011-4-28 15:17 编辑

进op安全模式好像有的机子是点qss(我的就是)

另外你把SecureCRT里的流控制全关掉
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
发表于 2011-4-28 15:16 | 显示全部楼层
忘记说了,捅的时候要定住,等第一个灯逛闪就已经进入安全模式,就可以telnet 192.168.1.1
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
 楼主| 发表于 2011-4-28 15:19 | 显示全部楼层
谢谢楼上的几位
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
发表于 2011-4-28 16:21 | 显示全部楼层
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

只能说,做u-boot的人很变态!
按什么键中止,也不提示。
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-11-1 07:07

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com

快速回复 返回顶部 返回列表