磊科NW736硬件疑问

be***

话说715p不稳定还有几天就过保的情况下，果断哪去保修，但是被告知停产，等2星期后，老板娘换了736给我。
回来之后一直觉得736不给力，但是TPY上面的硬件参数是5db*3，715p是4db*2，偶凌乱了。。。
放狗搜了几天，都说是BCM5357C0KFBG（某大神拆了散热上的图），4M ROM,16M RAM(这个没看好，是自己猜的，因为内存开机就占28%)；
http://bbs.uc.cn/thread-1759210-1-1.html 拆机图传送门
抱着必死无疑的心态，在磊科官网上下载了最新的715P固件，还有735的固件，直接web刷。。。
乖乖，还都能刷上，但是端口反了--> LAN4=WAN ，LAN3=LAN1....
反了不要紧，还只能无线了，有线不行了（具体表现为LAN可以，WAN不能DHCP上一级路由，用固定IP显示连接，但是不能使用）。。。
然后再找大神的经验试下刷DD。。传送门 5357刷 DD   http://itbbs.pconline.com.cn/diy/14571483.html
开始自作聪明，自己到DD官网找了5357 ，4M，32M的固件，下了 E1000的那个 16758，web一刷就半砖了。。。
后来还是老老实实tftp上了mini版的固件，dd是刷上了，但是有线还是不行。。。。。。。
于是想着看看硬件吧，但是进去后偶就凌乱了，不多说，上图吧。。。
求大神解答，是DD认错CPU了么？

be***

DD-WRT v24-sp2 mini (c) 2011 NewMedia-NET GmbH
Release: 09/09/11 (SVN revision: 17598)

BusyBox v1.13.4 (2011-09-09 10:33:33 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

root@DD-WRT:~# free
              total         used         free       shared      buffers
  Mem:        26216        12656        13560            0         1328
Swap:            0            0            0
Total:        26216        12656        13560
root@DD-WRT:~# df -h
Filesystem           1K-blocks      Used Available Use% Mounted on
/dev/root                 2048      2048         0 100% /

root@DD-WRT:/bin# dmesg
Linux version 2.6.24.111 (eko@dd-wrt) (gcc version 4.1.2) #3119 Fri Sep 9 10:36:08 CEST 2011
CPU revision is: 00019749
Found a 4MB ST compatible serial flash
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Entering add_active_range(0, 0, 8192) 0 entries of 256 used
Zone PFN ranges:
  Normal          0 ->     8192
  HighMem      8192 ->     8192
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->     8192
On node 0 totalpages: 8192
  Normal zone: 0 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8192 pages, LIFO batch:1
  HighMem zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order.  Total pages: 8192
Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCMd144 rev 1 at 300 MHz
Using 150.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26012k/32768k available (3481k kernel code, 6740k reserved, 1358k data, 188k init, 0k highmem)
Calibrating delay loop... 149.91 BogoMIPS (lpj=749568)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
PCI: no core
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
et_module_init: passivemode set to 0x0
PCI: Setting latency timer of device 0000:00:02.0 to 64
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.127
PCI: Setting latency timer of device 0000:00:01.0 to 64
pflash: found no supported devices
bootloader size: 131072
nvram size: 32768
sflash: Filesystem type: squashfs, size=0x1ed25c
partition size = 2053120
Creating 5 MTD partitions on "sflash":
0x00000000-0x00020000 : "cfe"
0x00020000-0x003f0000 : "linux"
0x0017ac00-0x00370000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
0x00370000-0x003f0000 : "ddwrt"
Broadcom Watchdog Timer: 0.07 initialized.
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length    128 bytes
PF_RING: ring slots       4096
PF_RING: sample rate      1 [1=no sampling]
PF_RING: capture TX       No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
decode 1f02
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 188k freed
roboswitch: Probing device eth0: found a 5325!
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device br0 entered promiscuous mode
device vlan0 entered promiscuous mode
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: port 1(vlan0) entering learning state
device br0 left promiscuous mode
device br0 entered promiscuous mode
device br0 left promiscuous mode
device br0 entered promiscuous mode
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan0) entering forwarding state
device vlan1 entered promiscuous mode
device vlan1 left promiscuous mode
etherip: Ethernet over IPv4 tunneling driver
device vlan0 left promiscuous mode
br0: port 1(vlan0) entering disabled state
device eth1 left promiscuous mode
br0: port 2(eth1) entering disabled state
device vlan0 entered promiscuous mode
br0: port 1(vlan0) entering learning state
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
device br0 left promiscuous mode
device br0 entered promiscuous mode
device br0 left promiscuous mode
device br0 entered promiscuous mode
br0: topology change detected, propagating
br0: port 1(vlan0) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
root@DD-WRT:/bin# cd bin

psl***

300MHZ，没错吧，就是5357

be***

psl001 发表于 2012-12-19 22:40
300MHZ，没错吧，就是5357

可能是DD还不认这货吧。。。
把路由型号也认错了
不知是不是和我之前刷的 E1000的固件有关。。

be***

亲自掀开散热看了  是5357 C0 。。。。。

沙龙***

直接硬改成235W

沙龙***

CFE文件不一样而已

沙龙***

交换芯片的驱动不一样而已

be***

沙龙斑竹 发表于 2012-12-26 12:37
交换芯片的驱动不一样而已

求235W 的 包

沙龙***

先换成235的CFE，然后再刷235的固件就没有问题了

be***

沙龙斑竹 发表于 2012-12-27 10:34
先换成235的CFE，然后再刷235的固件就没有问题了

斑竹 不好意思
偶台小白 不会刷CFE
求含CFE的235W固件
我直接编程器烧进去
再找人焊就好了  
呵呵  谢谢
见笑了

沙龙***

235W编程器固件要改MAC地址才行

be***

沙龙斑竹 发表于 2012-12-28 09:27
235W编程器固件要改MAC地址才行

改地址这活儿应该不难，
我有编程器，
告诉我字段应该就Ok了吧。。。
谢谢。。

田***

改nw735拨号已经正常，多了Qos,软改用用先。