找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 12105|回复: 25

超值FWR171(不带3G,58元)路由软硬件改造过程

[复制链接]
本帖最后由 Jason022 于 2013-1-16 15:50 编辑

前段时间想在坛里收一个703n或者马甲,一直没有合适的,后来从电商网站看到这个路由才58元,感觉超值,果断入手

头天晚上下单,第二天下午就收到了,通电试机没有问题,开拆。。。

原机不带usb,RAM是A3S28D40FTP(16M),spi flash是cFeon QH16-104HIP只有2M,全部拆下来准备更换

拆RAM芯片的时候一定要注意风枪温度不要太高,最好把板子悬空固定好再吹,因为pcb板子很薄,等上面焊锡化得时候下面的焊锡也差不多快化了,这时候不要动板子否则下面的器件就一团糟了。。。

准备换的W25Q64BV先用编程器写好程序再焊,我是用的并口简易编程器烧的,速度比较慢,但是比较实用。


下面是一些该机说明和图片,重要的地方都在图上标出来了






最后改装好的样子






本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

评分

参与人数 2恩山币 +2 收起 理由
ZHIZ*** + 1 感谢楼主
舒*** + 1 谢谢LZ分享!

查看全部评分

我的恩山、我的无线 The best wifi forum is right here.
 楼主| | 显示全部楼层
启动信息:

U-Boot 1.1.4 (Jan 14 2013 - 14:33:53)

AP121 (ar9330) U-boot

DRAM:  64 MB
led turning on for 1s...
id read 0x100000ff
flash size 16777216, sector count = 256
Flash: 16 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...

>aya,if any bad thing happen! ...
>aya,then i will going to web failsafe! ...
>the web failsafe is by great mips!...
-this is a uboot mod by slboat...

No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
I will autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.2.12 (zhm@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun May 20 02:02:11 PDT 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61804k/65536k available (2055k kernel code, 3732k reserved, 392k data, 192k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.330000] bio: create slab <bio-0> at 0
[    0.340000] Switching to clocksource MIPS
[    0.350000] NET: Registered protocol family 2
[    0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.350000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.360000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.360000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.370000] TCP reno registered
[    0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.380000] NET: Registered protocol family 1
[    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.410000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.430000] msgmni has been set to 120
[    0.430000] io scheduler noop registered
[    0.430000] io scheduler deadline registered (default)
[    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.440000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.460000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.470000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.470000] 5 tp-link partitions found on MTD device spi0.0
[    0.480000] Creating 5 MTD partitions on "spi0.0":
[    0.480000] 0x000000000000-0x000000020000 : "u-boot"
[    0.490000] 0x000000020000-0x0000000fa30c : "kernel"
[    0.490000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.510000] 0x0000000fa30c-0x0000007f0000 : "rootfs"
[    0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.520000] mtd: partition "rootfs" set to be root filesystem
[    0.530000] mtd: partition "rootfs_data" created automatically, ofs=340000, len=4B0000
[    0.540000] 0x000000340000-0x0000007f0000 : "rootfs_data"
[    0.540000] 0x0000007f0000-0x000000800000 : "art"
[    0.550000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.800000] ag71xx_mdio: probed
[    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.410000] TCP westwood registered
[    1.420000] NET: Registered protocol family 17
[    1.420000] 8021q: 802.1Q VLAN Support v1.8
[    1.440000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.450000] Freeing unused kernel memory: 192k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
f
- failsafe -


BusyBox v1.19.4 (2012-05-20 01:31:11 PDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
ATTITUDE ADJUSTMENT (bleeding edge, r31054) ----------
  * 1/4 oz Vodka      Pour all ingredients into mixing
  * 1/4 oz Gin        tin with ice, strain into glass.
  * 1/4 oz Amaretto
  * 1/4 oz Triple sec
  * 1/4 oz Peach schnapps
  * 1/4 oz Sour mix
  * 1 splash Cranberry juice
-----------------------------------------------------
root@(none):/#

点评

学习了,谢谢分享。  详情 回复 发表于 2014-7-25 16:40
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

来自手机 | 显示全部楼层
学习下,请问楼主在哪买的路由。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
ZHIZAI100 发表于 2013-1-16 19:56
学习下,请问楼主在哪买的路由。

亚马逊
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

Jason022 发表于 2013-1-16 20:08
亚马逊

非常感谢
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

LZ好人,活也棒!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

大神啊      
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

Jason022 发表于 2013-1-16 15:47
启动信息:

U-Boot 1.1.4 (Jan 14 2013 - 14:33:53)

怎么看到是16M的闪存???
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
zhujunsq 发表于 2013-1-18 23:54
怎么看到是16M的闪存???

这个Uboot是为16M flash写的,当然也能支持4M 8M,只是显示不对,如果你用4M的uboot,在uboot命令行是不能访问4M后面的地址空间
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

好厉害,收藏之
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

不错!我也准备把TTL做在我的HG255D的壳内,这样就不用拆机装机了,好烦的!呵呵!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

我也买了不带3G的fwr171,如果刷成703N,是不是只有编程器刷啊?当然rom得改成4m吧?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

楼主,有8M容量好的openwrt编程器固件吗
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

现在这个路由器更便宜了。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

谢谢楼主分享,了解一下。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-29 02:16

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表