1041n砖了，接ttl出现下面文字怎么处理，请教各位…………

sakul***

U-Boot 1.1.4 (Dec 31 2011 - 13:38:52)

U-boot MI124


DRAM:  32 MB
id read 0x100000ff
flash size 4MB, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp  reset mask:c03300
WASP  ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.3.8 (fnord@tschunk) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Wed Jul 11 08:28:33 UTC 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9342 rev 1
[    0.000000] Clocks: CPU:525.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR1041N-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28980k/32768k available (2208k kernel code, 3788k reserved, 578k data, 204k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 261.73 BogoMIPS (lpj=1308672)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR1041N v2
[    0.310000] bio: create slab <bio-0> at 0
[    0.320000] Switching to clocksource MIPS
[    0.330000] NET: Registered protocol family 2
[    0.330000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.330000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.340000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.340000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.350000] TCP reno registered
[    0.350000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.360000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.360000] NET: Registered protocol family 1
[    0.390000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.390000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.400000] msgmni has been set to 56
[    0.410000] io scheduler noop registered
[    0.410000] io scheduler deadline registered (default)
[    0.410000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
俽ⅹ倐倐陙serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.450000] console [ttyS0] enabled, bootconsole disabled
[    0.450000] console [ttyS0] enabled, bootconsole disabled
[    0.470000] m25p80 spi0.0: found en25q32b, expected m25p80
[    0.470000] m25p80 spi0.0: en25q32b (4096 Kbytes)
[    0.480000] 5 tp-link partitions found on MTD device spi0.0
[    0.490000] Creating 5 MTD partitions on "spi0.0":
[    0.490000] 0x000000000000-0x000000020000 : "u-boot"
[    0.500000] 0x000000020000-0x00000011bdb0 : "kernel"
[    0.500000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.520000] 0x00000011bdb0-0x0000003f0000 : "rootfs"
[    0.520000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.540000] mtd: partition "rootfs" set to be root filesystem
[    0.540000] mtd: partition "rootfs_data" created automatically, ofs=290000, len=160000
[    0.550000] 0x000000290000-0x0000003f0000 : "rootfs_data"
[    0.560000] 0x0000003f0000-0x000000400000 : "art"
[    0.570000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.590000] ag71xx_mdio: probed
[    0.720000] ag71xx_mdio: probed
[    0.730000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.310000] eth0: Atheros AR8327 switch driver attached.
[    2.460000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316]
[    2.470000] TCP cubic registered
[    2.480000] NET: Registered protocol family 17
[    2.480000] Bridge firewalling registered
[    2.480000] 8021q: 802.1Q VLAN Support v1.8
[    2.490000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.500000] Freeing unused kernel memory: 204k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
[    5.460000] eth0: link up (1000Mbps/Full duplex)
- regular preinit -
[    7.500000] JFFS2 notice: (489) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 9 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
[    7.670000] eth0: link down

Please press Enter to activate this console. [    8.440000] Compat-wireless backport release: compat-wireless-2012-07-03-2-3-g7adf66e
[    8.450000] Backport based on wireless-testing.git master-2012-07-06
[    8.460000] compat.git: wireless-testing.git
[    8.580000] cfg80211: Calling CRDA to update world regulatory domain
[    8.580000] cfg80211: World regulatory domain updated:
[    8.590000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.600000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.600000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.610000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.620000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.630000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.820000] usbcore: registered new interface driver usbfs
[    8.830000] usbcore: registered new interface driver hub
[    8.830000] usbcore: registered new device driver usb
[    9.260000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[    9.270000] cfg80211: Calling CRDA for country: US
[    9.270000] cfg80211: Regulatory domain changed to country: US
[    9.280000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.290000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    9.290000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[    9.300000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.310000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.320000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.330000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[    9.380000] PPP generic driver version 2.4.2
[    9.500000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.610000] NET: Registered protocol family 24
[    9.620000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.650000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[    9.850000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   12.540000] device eth0.1 entered promiscuous mode
[   12.540000] device eth0 entered promiscuous mode
[   13.680000] eth0: link up (1000Mbps/Full duplex)
[   13.720000] br-lan: port 1(eth0.1) entered forwarding state
[   13.720000] br-lan: port 1(eth0.1) entered forwarding state
[   15.720000] br-lan: port 1(eth0.1) entered forwarding state



BusyBox v1.19.4 (2012-07-10 22:12:33 UTC) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
-----------------------------------------------------
ATTITUDE ADJUSTMENT (Bleeding Edge, r32656)
-----------------------------------------------------
  * 1/4 oz Vodka      Pour all ingredients into mixing
  * 1/4 oz Gin        tin with ice, strain into glass.
  * 1/4 oz Amaretto
  * 1/4 oz Triple sec
  * 1/4 oz Peach schnapps
  * 1/4 oz Sour mix
  * 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/#

xi5***

ttl  刷固件

五度***

砖机救活了吗？

savi***

输入firstboot。然后是reboot