【求助】恩山前所未有的怪异问题

qq175668543

前一段买了个843N 带了两FLASH 200大洋 回家之后改了IPX座和双FLASH底座 现在可以直插双FLASH板 一片是卖家的OP 有片自己要求的843ND英文固件
回来后脱机玩，某天下午脱机过程中突然停电，回家后发现OP的固件挂了 直接砖机 U-BOOT挂了 于是用用另一片FLASH恢复 救活U-boot发现两个FLASH、U-BOOT都正常，刷固件都能刷进去 但是就是启动不了 于是狂谷歌 ，发现这问题果然前所未有。
TTL如下：
U-Boot 1.1.4 (Oct  9 2012 - 12:34:07)

U-boot AP123 for WR843N

  Build by IronCake(QQ:110782278)

  Taobao: http://happyrho.taobao.com


DRAM:  64 MB
id read 0x100000ff
Flash: 16 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag934x_enet_initialize...
Fetching MAC Address from 0x83ff1888
Fetching MAC Address from 0x83ff1888
wasp reset mask:c03300
WASP ----> S27 PHY
GMAC: cfg1 0x5 cfg2 0x7114
eth0: 00:00:00:00:00:01
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 0: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0: 0x10
eth0 up
WASP ----> S27 PHY
GMAC: cfg1 0xf cfg2 0x7214
eth1: 00:00:00:00:00:00
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 1: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 4: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4: 0x10
eth1 up
eth0, eth1
eth0 link down
eth1 link down
Autobooting in 3 seconds, press "t" to stop
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.3.8 (feixiang@openwrt.org.cn) (gcc version 4.6.3
20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #21 Wed Oct 10 11:36:50 CST 201
2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9341 rev 1
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.00
0MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 16256
[    0.000000] Kernel command line:  board=TL-WR843N-v1 console=ttyS0,115200 roo
tfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61580k/65536k available (2144k kernel code, 3956k reserve
d, 401k data, 208k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, No
des=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR843N/ND v1

敢问有没有高人能解决，卖家说要自己从京东买个新的换板，

hijk1

不知道
友情帮顶了。