我的路由通过ttl串口上去，键盘输入有问题大家给我看看

wenhairong

UART1 output test ok

Uart init

mfid=000000c2 devid=00002249

Found 1 x 2M flash memory



---RealTek(RTL8186)at 2005.06.06-11:22+0800 version 1.3c [32bit](180MHz)

no sys signature at 00010000!

Jump to image start=0x80300000...

early printk enabled

Determined physical RAM map:

memory: 01000000 @ 00000000 (usable)

On node 0 totalpages: 4096

zone(0): 4096 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: root=/dev/mtdblock1 console=0 single

Calibrating delay loop... 179.40 BogoMIPS

Memory: 14380k/16384k available (1446k kernel code, 2004k reserved, 124k data, 48k init, 0k highmem)

Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)

Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 4096 (order: 2, 16384 bytes)

check_wait... unavailable.

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

Serial driver version 6.02 (2003-03-12) with no serial options enabled

ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1

state->flags=00000000

Realtek GPIO Driver for Flash Reload Default

block: 64 slots per queue, batch=16

SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).

CSLIP: code copyright 1989 Regents of the University of California.

PPP generic driver version 2.4.1

MPPE/MPPC encryption/compression module registered

RealTek E-Flash System Driver. (C) 2002 RealTek Corp.

Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000

Creating 2 MTD partitions on "DiskOnChip Millennium":

0x00000000-0x00100000 : "boot+cfg+linux"

0x00100000-0x00200000 : "root fs"

RTL8185 driver version 1.9 (2006-03-31)

rtl8186_init: Loading new ethernet driver!!

8186NIC Ethernet driver v0.0.4 (Sep 23, 2005)

eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4

eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5

nat_speed_init (v1.1)

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 1024 bind 204

ip_conntrack version 2.1 (128 buckets, 1024 max) - 312 bytes per conntrack

PPTP netfilter connection tracking: registered

PPTP netfilter NAT helper: registered

ip_tables: (C) 2000-2002 Netfilter core team

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

NET4: Ethernet Bridge 008 for NET4.0

VFS: Mounted root (squashfs filesystem) readonly.

Freeing unused kernel memory: 48k freed

mount /proc file system ok!

mount /var  file system ok!

serial console detected.  Disabling virtual terminals.

init started:  BusyBox v1.00-pre8 (2005.06.01-13:21+0000) multi-call binary





BusyBox v1.00-pre8 (2005.06.01-13:21+0000) Built-in shell (msh)

Enter 'help' for a list of built-in commands.



^@BusyBox v1.00-pre8 (2005.06.01-13:21+0000) multi-call binary



Usage: cp [OPTION]... SOURCE DEST
#
#
#


奇怪的是只有按空格键才能进入shell cp命令是按空格自动出现，键盘输入有问题有些键输入回显二个字符,例如输入's' 回显'sF'  enter 键也不能使用.

fxlz

这是什么路由器