[呃……测试失败]需要一位千兆WAN版HG255D测试者！

981***

我尝试在dts里面启用了GMAC并且安装了Realtek PHY驱动，需要一位使用千兆WAN版HG255D的人测试下WAN口是否可用！(测试结果……尼玛内核里面的Realtek PHY不带RTL8211CL驱动（虽然我怎么觉得好像即使有带也没办法用……）……看了下rt-n14u的gpl里面的raeth……对phy的操作全部集成在了驱动里面……尝试失败……)

andy***

围观....楼主还是自己想办法吧~~~

zouj***

我来试试~~~

981***

zoujack1 发表于 2014-8-20 09:06
我来试试~~~

首次启动时间可能有点长……2分钟左右……

liushu***

楼主，你的固件 41945-openwrt-ramips-rt305x-hg255d-squashfs-sysupgrade ，用3g上网卡时直接插在hg255的usb口上时usbmode可以正常识别并使用，但是在hg255的USB口上接一个usb集线器，然后3g上网卡接在usb集线器上时usbmode不生成ttyUSB0，ttyUSB1，ttyUSB2，3g网卡无法使用。。。。请问有什么解决方法吗？

981***

liushuailynn 发表于 2014-8-20 09:13
楼主，你的固件 41945-openwrt-ramips-rt305x-hg255d-squashfs-sysupgrade ，用3g上网卡时直接插在hg255的u ...

不好意思忘了装hub驱动……下一版会补上的……

zwweil***

不能用

zwweil***

1. [    0.000000] Linux version 3.10.49 (user@guoguopc-lan) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41599) ) #2 Wed Aug 20 08:28:49 CST 2014
   
2. [    0.000000] SoC Type: Ralink RT3052 id:1 rev:3
   
3. [    0.000000] bootconsole [early0] enabled
   
4. [    0.000000] CPU revision is: 0001964c (MIPS 24KEc)
   
5. [    0.000000] MIPS: machine is HuaWei HG255D
   
6. [    0.000000] Determined physical RAM map:
   
7. [    0.000000]  memory: 02000000 @ 00000000 (usable)
   
8. [    0.000000] Initrd not found or empty - disabling initrd
   
9. [    0.000000] Zone ranges:
   
10. [    0.000000]   Normal   [mem 0x00000000-0x01ffffff]
    
11. [    0.000000] Movable zone start for each node
    
12. [    0.000000] Early memory node ranges
    
13. [    0.000000]   node   0: [mem 0x00000000-0x01ffffff]
    
14. [    0.000000] On node 0 totalpages: 8192
    
15. [    0.000000] free_area_init_node: node 0, pgdat 80296990, node_mem_map 81003d20
    
16. [    0.000000]   Normal zone: 64 pages used for memmap
    
17. [    0.000000]   Normal zone: 0 pages reserved
    
18. [    0.000000]   Normal zone: 8192 pages, LIFO batch:0
    
19. [    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
    
20. [    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
    
21. [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
    
22. [    0.000000] pcpu-alloc: [0] 0
    
23. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
    
24. [    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
    
25. [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
    
26. [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
    
27. [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
    
28. [    0.000000] Writing ErrCtl register=0003cc50
    
29. [    0.000000] Readback ErrCtl register=0003cc50
    
30. [    0.000000] Memory: 29292k/32768k available (2179k kernel code, 3476k reserved, 556k data, 204k init, 0k highmem)
    
31. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    
32. [    0.000000] NR_IRQS:256
    
33. [    0.000000] CPU Clock: 384MHz
    
34. [    0.070000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
    
35. [    0.070000] pid_max: default: 32768 minimum: 301
    
36. [    0.080000] Mount-cache hash table entries: 512
    
37. [    0.090000] pinctrl core: initialized pinctrl subsystem
    
38. [    0.100000] NET: Registered protocol family 16
    
39. [    0.110000] rt2880-pinmux pinctrl.1: try to register 52 pins ...
    
40. [    0.110000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
    
41. [    0.110000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
    
42. [    0.110000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
    
43. [    0.110000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
    
44. [    0.110000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
    
45. [    0.110000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
    
46. [    0.110000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
    
47. [    0.110000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
    
48. [    0.110000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
    
49. [    0.110000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
    
50. [    0.110000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
    
51. [    0.110000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
    
52. [    0.110000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
    
53. [    0.110000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
    
54. [    0.110000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
    
55. [    0.110000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
    
56. [    0.110000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
    
57. [    0.110000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
    
58. [    0.110000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
    
59. [    0.110000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
    
60. [    0.110000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
    
61. [    0.110000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
    
62. [    0.110000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
    
63. [    0.110000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
    
64. [    0.110000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
    
65. [    0.110000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
    
66. [    0.110000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
    
67. [    0.110000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
    
68. [    0.110000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux
    
69. [    0.110000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux
    
70. [    0.110000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux
    
71. [    0.110000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux
    
72. [    0.110000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux
    
73. [    0.110000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux
    
74. [    0.110000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux
    
75. [    0.110000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux
    
76. [    0.110000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux
    
77. [    0.110000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux
    
78. [    0.110000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux
    
79. [    0.110000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux
    
80. [    0.110000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux
    
81. [    0.110000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux
    
82. [    0.110000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux
    
83. [    0.110000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux
    
84. [    0.110000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux
    
85. [    0.110000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux
    
86. [    0.110000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux
    
87. [    0.110000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux
    
88. [    0.110000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux
    
89. [    0.110000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux
    
90. [    0.110000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux
    
91. [    0.110000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux
    
92. [    0.110000] pinctrl core: add 7 pinmux maps
    
93. [    0.110000] rt2880-pinmux pinctrl.1: found group selector 7 for sdram
    
94. [    0.110000] rt2880-pinmux pinctrl.1: found group selector 1 for spi
    
95. [    0.110000] rt2880-pinmux pinctrl.1: found group selector 0 for i2c
    
96. [    0.110000] rt2880-pinmux pinctrl.1: found group selector 4 for jtag
    
97. [    0.110000] rt2880-pinmux pinctrl.1: found group selector 6 for rgmii
    
98. [    0.110000] rt2880-pinmux pinctrl.1: found group selector 5 for mdio
    
99. [    0.110000] rt2880-pinmux pinctrl.1: found group selector 2 for uartf
    
100. [    0.110000] rt2880-pinmux pinctrl.1: request pin 24 (io24) for pinctrl.1
     
101. [    0.110000] rt2880-pinmux pinctrl.1: request pin 25 (io25) for pinctrl.1
     
102. [    0.110000] rt2880-pinmux pinctrl.1: request pin 26 (io26) for pinctrl.1
     
103. [    0.110000] rt2880-pinmux pinctrl.1: request pin 27 (io27) for pinctrl.1
     
104. [    0.110000] rt2880-pinmux pinctrl.1: request pin 28 (io28) for pinctrl.1
     
105. [    0.110000] rt2880-pinmux pinctrl.1: request pin 29 (io29) for pinctrl.1
     
106. [    0.110000] rt2880-pinmux pinctrl.1: request pin 30 (io30) for pinctrl.1
     
107. [    0.110000] rt2880-pinmux pinctrl.1: request pin 31 (io31) for pinctrl.1
     
108. [    0.110000] rt2880-pinmux pinctrl.1: request pin 32 (io32) for pinctrl.1
     
109. [    0.110000] rt2880-pinmux pinctrl.1: request pin 33 (io33) for pinctrl.1
     
110. [    0.110000] rt2880-pinmux pinctrl.1: request pin 34 (io34) for pinctrl.1
     
111. [    0.110000] rt2880-pinmux pinctrl.1: request pin 35 (io35) for pinctrl.1
     
112. [    0.110000] rt2880-pinmux pinctrl.1: request pin 36 (io36) for pinctrl.1
     
113. [    0.120000] rt2880-pinmux pinctrl.1: request pin 37 (io37) for pinctrl.1
     
114. [    0.120000] rt2880-pinmux pinctrl.1: request pin 38 (io38) for pinctrl.1
     
115. [    0.120000] rt2880-pinmux pinctrl.1: request pin 39 (io39) for pinctrl.1
     
116. [    0.120000] rt2880-pinmux pinctrl.1: request pin 3 (io3) for pinctrl.1
     
117. [    0.120000] rt2880-pinmux pinctrl.1: request pin 4 (io4) for pinctrl.1
     
118. [    0.120000] rt2880-pinmux pinctrl.1: request pin 5 (io5) for pinctrl.1
     
119. [    0.120000] rt2880-pinmux pinctrl.1: request pin 6 (io6) for pinctrl.1
     
120. [    0.120000] rt2880-pinmux pinctrl.1: request pin 1 (io1) for pinctrl.1
     
121. [    0.120000] rt2880-pinmux pinctrl.1: request pin 2 (io2) for pinctrl.1
     
122. [    0.120000] rt2880-pinmux pinctrl.1: request pin 17 (io17) for pinctrl.1
     
123. [    0.120000] rt2880-pinmux pinctrl.1: request pin 18 (io18) for pinctrl.1
     
124. [    0.120000] rt2880-pinmux pinctrl.1: request pin 19 (io19) for pinctrl.1
     
125. [    0.120000] rt2880-pinmux pinctrl.1: request pin 20 (io20) for pinctrl.1
     
126. [    0.120000] rt2880-pinmux pinctrl.1: request pin 21 (io21) for pinctrl.1
     
127. [    0.120000] rt2880-pinmux pinctrl.1: request pin 40 (io40) for pinctrl.1
     
128. [    0.120000] rt2880-pinmux pinctrl.1: request pin 41 (io41) for pinctrl.1
     
129. [    0.120000] rt2880-pinmux pinctrl.1: request pin 42 (io42) for pinctrl.1
     
130. [    0.120000] rt2880-pinmux pinctrl.1: request pin 43 (io43) for pinctrl.1
     
131. [    0.120000] rt2880-pinmux pinctrl.1: request pin 44 (io44) for pinctrl.1
     
132. [    0.120000] rt2880-pinmux pinctrl.1: request pin 45 (io45) for pinctrl.1
     
133. [    0.120000] rt2880-pinmux pinctrl.1: request pin 46 (io46) for pinctrl.1
     
134. [    0.120000] rt2880-pinmux pinctrl.1: request pin 47 (io47) for pinctrl.1
     
135. [    0.120000] rt2880-pinmux pinctrl.1: request pin 48 (io48) for pinctrl.1
     
136. [    0.120000] rt2880-pinmux pinctrl.1: request pin 49 (io49) for pinctrl.1
     
137. [    0.120000] rt2880-pinmux pinctrl.1: request pin 50 (io50) for pinctrl.1
     
138. [    0.120000] rt2880-pinmux pinctrl.1: request pin 51 (io51) for pinctrl.1
     
139. [    0.120000] rt2880-pinmux pinctrl.1: request pin 22 (io22) for pinctrl.1
     
140. [    0.120000] rt2880-pinmux pinctrl.1: request pin 23 (io23) for pinctrl.1
     
141. [    0.120000] rt2880-pinmux pinctrl.1: request pin 7 (io7) for pinctrl.1
     
142. [    0.120000] rt2880-pinmux pinctrl.1: request pin 8 (io8) for pinctrl.1
     
143. [    0.120000] rt2880-pinmux pinctrl.1: request pin 9 (io9) for pinctrl.1
     
144. [    0.120000] rt2880-pinmux pinctrl.1: request pin 10 (io10) for pinctrl.1
     
145. [    0.120000] rt2880-pinmux pinctrl.1: request pin 11 (io11) for pinctrl.1
     
146. [    0.120000] rt2880-pinmux pinctrl.1: request pin 12 (io12) for pinctrl.1
     
147. [    0.120000] rt2880-pinmux pinctrl.1: request pin 13 (io13) for pinctrl.1
     
148. [    0.120000] rt2880-pinmux pinctrl.1: request pin 14 (io14) for pinctrl.1
     
149. [    0.120000] rt2880-pinmux pinctrl.1: failed to lookup the sleep state
     
150. [    0.140000] bio: create slab <bio-0> at 0
     
151. [    0.140000] rt2880_gpio 10000600.gpio: registering 24 gpios
     
152. [    0.150000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
     
153. [    0.160000] Switching to clocksource MIPS
     
154. [    0.170000] NET: Registered protocol family 2
     
155. [    0.180000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
     
156. [    0.190000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
     
157. [    0.210000] TCP: Hash tables configured (established 512 bind 512)
     
158. [    0.220000] TCP: reno registered
     
159. [    0.230000] UDP hash table entries: 256 (order: 0, 4096 bytes)
     
160. [    0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
     
161. [    0.250000] NET: Registered protocol family 1
     
162. [    0.260000] rt-timer 10000100.timer: maximum frequncy is 7812Hz
     
163. [    0.270000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
     
164. [    0.300000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
     
165. [    0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
     
166. [    0.330000] msgmni has been set to 57
     
167. [    0.340000] io scheduler noop registered
     
168. [    0.350000] io scheduler deadline registered (default)
     
169. [    0.360000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
     
170. [    0.380000] serial8250 serial8250: no of_node; not parsing pinctrl DT
     
171. [    0.380000] pinctrl core: add 1 pinmux maps
     
172. [    0.380000] rt2880-pinmux pinctrl.1: found group selector 3 for uartlite
     
173. [    0.380000] rt2880-pinmux pinctrl.1: request pin 15 (io15) for 10000c00.uartlite
     
174. [    0.380000] rt2880-pinmux pinctrl.1: request pin 16 (io16) for 10000c00.uartlite
     
175. [    0.380000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
     
176. [    0.390000] console [ttyS0] enabled, bootconsole disabled
     
177. [    0.410000] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
     
178. [    0.420000] Amd/Fujitsu Extended Query Table at 0x0040
     
179. [    0.420000]   Amd/Fujitsu Extended Query version 1.3.
     
180. [    0.430000] number of CFI chips: 1
     
181. [    0.430000] 5 ofpart partitions found on MTD device 1f000000.cfi
     
182. [    0.440000] Creating 5 MTD partitions on "1f000000.cfi":
     
183. [    0.440000] 0x000000000000-0x000000040000 : "u-boot"
     
184. [    0.450000] 0x000000040000-0x000000060000 : "u-boot-env"
     
185. [    0.460000] 0x000000060000-0x000000080000 : "factory"
     
186. [    0.470000] 0x000000080000-0x000000fe0000 : "firmware"
     
187. [    0.470000] 0x000000177550-0x000000fe0000 : "rootfs"
     
188. [    0.480000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
     
189. [    0.500000] mtd: device 4 (rootfs) set to be root filesystem
     
190. [    0.500000] mtd: partition "rootfs_data" created automatically, ofs=0xa00000, len=0x5e0000
     
191. [    0.510000] 0x000000a00000-0x000000fe0000 : "rootfs_data"
     
192. [    0.520000] 0x000000fa0000-0x000000fc0000 : "factory-orig"
     
193. [    0.530000] eth0: done loading
     
194. [    0.540000] rt2880_wdt 10000120.watchdog: Initialized
     
195. [    0.550000] TCP: cubic registered
     
196. [    0.550000] NET: Registered protocol family 17
     
197. [    0.550000] 8021q: 802.1Q VLAN Support v1.8
     
198. [    0.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
     
199. [    0.570000] Freeing unused kernel memory: 204K (802ad000 - 802e0000)
     
200. [    4.610000] usbcore: registered new interface driver usbfs
     
201. [    4.620000] usbcore: registered new interface driver hub
     
202. [    4.620000] usbcore: registered new device driver usb
     
203. [    4.670000] rt2880-pinmux pinctrl.1: request pin 4 (io4) for pio:4
     
204. [    4.670000] rt2880-pinmux pinctrl.1: request pin 10 (io10) for pio:10
     
205. [    4.670000] rt2880-pinmux pinctrl.1: request pin 0 (io0) for pio:0
     
206. [    4.680000] SCSI subsystem initialized
     
207. [    4.700000] dwc_otg: version 2.72a 24-JUN-2008
     
208. [    4.700000] dwc_otg: Core Release: 2.66a
     
209. [    4.900000] dwc_otg: Periodic Transfer Interrupt Enhancement - disabled
     
210. [    4.910000] dwc_otg: Multiprocessor Interrupt Enhancement - disabled
     
211. [    4.920000] dwc_otg: Using DMA mode
     
212. [    4.920000] dwc_otg: Device using Buffer DMA mode
     
213. [    4.930000] dwc_otg 101c0000.otg: DWC OTG Controller
     
214. [    4.930000] dwc_otg 101c0000.otg: new USB bus registered, assigned bus number 1
     
215. [    4.940000] dwc_otg 101c0000.otg: irq 26, io mem 0x101c0000
     
216. [    4.940000] dwc_otg: Init: Port Power? op_state=1
     
217. [    4.950000] dwc_otg: Init: Power Port (0)
     
218. [    4.950000] usb usb1: no of_node; not parsing pinctrl DT
     
219. [    4.950000] hub 1-0:1.0: no of_node; not parsing pinctrl DT
     
220. [    4.950000] hub 1-0:1.0: USB hub found
     
221. [    4.960000] hub 1-0:1.0: 1 port detected
     
222. [    4.970000] leds-gpio gpio-leds.3: pins are not configured from the driver
     
223. [    4.970000] rt2880-pinmux pinctrl.1: request pin 8 (io8) for pio:8
     
224. [    4.970000] rt2880-pinmux pinctrl.1: request pin 13 (io13) for pio:13
     
225. [    4.970000] rt2880-pinmux pinctrl.1: request pin 14 (io14) for pio:14
     
226. [    4.970000] rt2880-pinmux pinctrl.1: request pin 9 (io9) for pio:9
     
227. [    4.970000] rt2880-pinmux pinctrl.1: request pin 12 (io12) for pio:12
     
228. [    4.980000] rt2880-pinmux pinctrl.1: request pin 5 (io5) for pio:5
     
229. [    4.980000] usbcore: registered new interface driver usb-storage
     
230. [   15.010000] NET: Registered protocol family 10
     
231. [   15.110000] tun: Universal TUN/TAP device driver, 1.6
     
232. [   15.120000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
     
233. [   15.150000] sit: IPv6 over IPv4 tunneling driver
     
234. [   15.200000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
     
235. [   15.350000] ip6_tables: (C) 2000-2006 Netfilter Core Team
     
236. [   15.400000] Linux video capture interface: v2.00
     
237. [   15.430000] u32 classifier
     
238. [   15.430000]     input device check on
     
239. [   15.440000]     Actions configured
     
240. [   15.600000] Mirror/redirect action on
     
241. [   15.640000] Failed to load ipt action
     
242. [   15.660000] fuse init (API version 7.22)
     
243. [   15.680000] usbcore: registered new interface driver cdc_acm
     
244. [   15.680000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
     
245. [   15.700000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
     
246. [   15.700000] Backport generated by backports.git backports-20140320-37-g5c33da0
     
247. [   15.720000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
     
248. [   15.730000]         Hooking IMQ before NAT on PREROUTING.
     
249. [   15.740000]         Hooking IMQ after NAT on POSTROUTING.
     
250. [   15.760000] ip_tables: (C) 2000-2006 Netfilter Core Team
     
251. [   15.820000] usbcore: registered new interface driver Philips webcam
     
252. [   15.860000] usbcore: registered new interface driver ums-alauda
     
253. [   15.880000] usbcore: registered new interface driver ums-cypress
     
254. [   15.910000] usbcore: registered new interface driver ums-datafab
     
255. [   15.930000] usbcore: registered new interface driver ums-freecom
     
256. [   15.950000] usbcore: registered new interface driver ums-isd200
     
257. [   15.970000] usbcore: registered new interface driver ums-jumpshot
     
258. [   16.010000] usbcore: registered new interface driver ums-karma
     
259. [   16.030000] usbcore: registered new interface driver ums-sddr09
     
260. [   16.050000] usbcore: registered new interface driver ums-sddr55
     
261. [   16.060000] usbcore: registered new interface driver ums-usbat
     
262. [   16.080000] usbcore: registered new interface driver usblp
     
263. [   16.100000] usbcore: registered new interface driver usbserial
     
264. [   16.100000] usbcore: registered new interface driver usbserial_generic
     
265. [   16.120000] usbserial: USB Serial support registered for generic
     
266. [   16.140000] usbcore: registered new interface driver uvcvideo
     
267. [   16.140000] USB Video Class driver (1.1.1)
     
268. [   16.290000] xt_time: kernel timezone is -0000
     
269. [   16.380000] gspca_main: v2.14.0 registered
     
270. [   16.400000] cfg80211: Calling CRDA to update world regulatory domain
     
271. [   16.480000] cfg80211: World regulatory domain updated:
     
272. [   16.480000] cfg80211:  DFS Master region: unset
     
273. [   16.480000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
     
274. [   16.490000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
     
275. [   16.500000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
     
276. [   16.510000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
     
277. [   16.520000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
     
278. [   16.530000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
     
279. [   16.530000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
     
280. [   16.540000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
     
281. [   16.550000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
     
282. [   16.620000] PPP generic driver version 2.4.2
     
283. [   16.650000] NET: Registered protocol family 24
     
284. [   16.690000] usbcore: registered new interface driver rt73usb
     
285. [   16.710000] usbcore: registered new interface driver rtl8187
     
286. [   16.750000] usbcore: registered new interface driver snd-usb-audio
     
287. [   16.830000] usbcore: registered new interface driver option
     
288. [   16.830000] usbserial: USB Serial support registered for GSM modem (1-port)
     
289. [   16.850000] usbcore: registered new interface driver rt2500usb
     
290. [   16.890000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
     
291. [   16.900000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
     
292. [   16.910000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
     
293. [   16.940000] usbcore: registered new interface driver rt2800usb
     
294. [   17.010000] usbcore: registered new interface driver ath9k_htc
     
295. [   17.020000] usbcore: registered new interface driver rtl8192cu
     
296. [   20.760000] rt305x-esw 10110000.esw: link changed 0x03
     
297. [   32.450000] device eth0.1 entered promiscuous mode
     
298. [   32.460000] device eth0 entered promiscuous mode
     
299. [   32.470000] br-lan: port 1(eth0.1) entered forwarding state
     
300. [   32.470000] br-lan: port 1(eth0.1) entered forwarding state
     
301. [   34.110000] cfg80211: Calling CRDA for country: CN
     
302. [   34.190000] cfg80211: Regulatory domain changed to country: CN
     
303. [   34.200000] cfg80211:  DFS Master region: FCC
     
304. [   34.200000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
     
305. [   34.210000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
     
306. [   34.220000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
     
307. [   34.230000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
     
308. [   34.230000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
     
309. [   34.240000] cfg80211:   (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
     
310. [   34.250000] cfg80211:   (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm), (N/A)
     
311. [   34.260000] cfg80211:   (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
     
312. [   34.470000] br-lan: port 1(eth0.1) entered forwarding state
     
313. [   38.340000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
     
314. [   38.380000] device wlan0 entered promiscuous mode
     
315. [   48.430000] br-lan: port 2(wlan0) entered forwarding state
     
316. [   48.430000] br-lan: port 2(wlan0) entered forwarding state
     
317. [   48.440000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
     
318. [   50.430000] br-lan: port 2(wlan0) entered forwarding state
     
319. [  109.020000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
     
320. [  109.020000] jffs2_build_filesystem(): unlocking the mtd device... done.
     
321. [  127.760000] rt305x-esw 10110000.esw: link changed 0x03
     
322. [  109.030000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
     
323. [  128.880000] jffs2: notice: (2250) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
     
324. [  168.150000] rt305x-esw 10110000.esw: link changed 0x03

复制代码

zwweil***

1. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.920000] dwc_otg: Using DMA mode
   
2. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.920000] dwc_otg: Device using Buffer DMA mode
   
3. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.930000] dwc_otg 101c0000.otg: DWC OTG Controller
   
4. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.930000] dwc_otg 101c0000.otg: new USB bus registered, assigned bus number 1
   
5. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.940000] dwc_otg 101c0000.otg: irq 26, io mem 0x101c0000
   
6. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.940000] dwc_otg: Init: Port Power? op_state=1
   
7. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.950000] dwc_otg: Init: Power Port (0)
   
8. Wed Aug 20 08:28:23 2014 kern.debug kernel: [    4.950000] usb usb1: no of_node; not parsing pinctrl DT
   
9. Wed Aug 20 08:28:23 2014 kern.debug kernel: [    4.950000] hub 1-0:1.0: no of_node; not parsing pinctrl DT
   
10. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.950000] hub 1-0:1.0: USB hub found
    
11. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.960000] hub 1-0:1.0: 1 port detected
    
12. Wed Aug 20 08:28:23 2014 kern.warn kernel: [    4.970000] leds-gpio gpio-leds.3: pins are not configured from the driver
    
13. Wed Aug 20 08:28:23 2014 kern.debug kernel: [    4.970000] rt2880-pinmux pinctrl.1: request pin 8 (io8) for pio:8
    
14. Wed Aug 20 08:28:23 2014 kern.debug kernel: [    4.970000] rt2880-pinmux pinctrl.1: request pin 13 (io13) for pio:13
    
15. Wed Aug 20 08:28:23 2014 kern.debug kernel: [    4.970000] rt2880-pinmux pinctrl.1: request pin 14 (io14) for pio:14
    
16. Wed Aug 20 08:28:23 2014 kern.debug kernel: [    4.970000] rt2880-pinmux pinctrl.1: request pin 9 (io9) for pio:9
    
17. Wed Aug 20 08:28:23 2014 kern.debug kernel: [    4.970000] rt2880-pinmux pinctrl.1: request pin 12 (io12) for pio:12
    
18. Wed Aug 20 08:28:23 2014 kern.debug kernel: [    4.980000] rt2880-pinmux pinctrl.1: request pin 5 (io5) for pio:5
    
19. Wed Aug 20 08:28:23 2014 kern.info kernel: [    4.980000] usbcore: registered new interface driver usb-storage
    
20. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.010000] NET: Registered protocol family 10
    
21. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.110000] tun: Universal TUN/TAP device driver, 1.6
    
22. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.120000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    
23. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.150000] sit: IPv6 over IPv4 tunneling driver
    
24. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.200000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
    
25. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.350000] ip6_tables: (C) 2000-2006 Netfilter Core Team
    
26. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.400000] Linux video capture interface: v2.00
    
27. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.430000] u32 classifier
    
28. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.430000]     input device check on
    
29. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.440000]     Actions configured
    
30. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.600000] Mirror/redirect action on
    
31. Wed Aug 20 08:28:23 2014 kern.warn kernel: [   15.640000] Failed to load ipt action
    
32. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.660000] fuse init (API version 7.22)
    
33. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.680000] usbcore: registered new interface driver cdc_acm
    
34. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.680000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
    
35. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.700000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
    
36. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.700000] Backport generated by backports.git backports-20140320-37-g5c33da0
    
37. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.720000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
    
38. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.730000]         Hooking IMQ before NAT on PREROUTING.
    
39. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.740000]         Hooking IMQ after NAT on POSTROUTING.
    
40. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.760000] ip_tables: (C) 2000-2006 Netfilter Core Team
    
41. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.820000] usbcore: registered new interface driver Philips webcam
    
42. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.860000] usbcore: registered new interface driver ums-alauda
    
43. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.880000] usbcore: registered new interface driver ums-cypress
    
44. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.910000] usbcore: registered new interface driver ums-datafab
    
45. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.930000] usbcore: registered new interface driver ums-freecom
    
46. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.950000] usbcore: registered new interface driver ums-isd200
    
47. Wed Aug 20 08:28:23 2014 kern.info kernel: [   15.970000] usbcore: registered new interface driver ums-jumpshot
    
48. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.010000] usbcore: registered new interface driver ums-karma
    
49. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.030000] usbcore: registered new interface driver ums-sddr09
    
50. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.050000] usbcore: registered new interface driver ums-sddr55
    
51. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.060000] usbcore: registered new interface driver ums-usbat
    
52. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.080000] usbcore: registered new interface driver usblp
    
53. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.100000] usbcore: registered new interface driver usbserial
    
54. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.100000] usbcore: registered new interface driver usbserial_generic
    
55. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.120000] usbserial: USB Serial support registered for generic
    
56. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.140000] usbcore: registered new interface driver uvcvideo
    
57. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.140000] USB Video Class driver (1.1.1)
    
58. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.290000] xt_time: kernel timezone is -0000
    
59. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.380000] gspca_main: v2.14.0 registered
    
60. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.400000] cfg80211: Calling CRDA to update world regulatory domain
    
61. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.480000] cfg80211: World regulatory domain updated:
    
62. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.480000] cfg80211:  DFS Master region: unset
    
63. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.480000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
    
64. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.490000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
    
65. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.500000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
    
66. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.510000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
    
67. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.520000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
    
68. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.530000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
    
69. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.530000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
    
70. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.540000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
    
71. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.550000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
    
72. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.620000] PPP generic driver version 2.4.2
    
73. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.650000] NET: Registered protocol family 24
    
74. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.690000] usbcore: registered new interface driver rt73usb
    
75. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.710000] usbcore: registered new interface driver rtl8187
    
76. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.750000] usbcore: registered new interface driver snd-usb-audio
    
77. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.830000] usbcore: registered new interface driver option
    
78. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.830000] usbserial: USB Serial support registered for GSM modem (1-port)
    
79. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.850000] usbcore: registered new interface driver rt2500usb
    
80. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.890000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
    
81. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.900000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
    
82. Wed Aug 20 08:28:23 2014 kern.debug kernel: [   16.910000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
    
83. Wed Aug 20 08:28:23 2014 kern.info kernel: [   16.940000] usbcore: registered new interface driver rt2800usb
    
84. Wed Aug 20 08:28:23 2014 kern.info kernel: [   17.010000] usbcore: registered new interface driver ath9k_htc
    
85. Wed Aug 20 08:28:23 2014 kern.info kernel: [   17.020000] usbcore: registered new interface driver rtl8192cu
    
86. Wed Aug 20 08:28:23 2014 kern.info kernel: [   20.760000] rt305x-esw 10110000.esw: link changed 0x03
    
87. Wed Aug 20 08:28:24 2014 user.emerg syslog: Error: Failed to connect to ubus
    
88. Wed Aug 20 08:28:24 2014 user.emerg syslog: uci: Entry not found
    
89. Wed Aug 20 08:28:24 2014 user.emerg syslog: uci: Entry not found
    
90. Wed Aug 20 08:28:24 2014 user.emerg syslog: uci: Entry not found
    
91. Wed Aug 20 08:28:24 2014 user.emerg syslog: MACVLAN is disabled.
    
92. Wed Aug 20 08:28:26 2014 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
    
93. Wed Aug 20 08:28:26 2014 user.err syslog: mounting /dev/mtdblock4 (squashfs) as /mnt/mtdblock4 failed (-1) - Unknown error -1
    
94. Wed Aug 20 08:28:26 2014 user.emerg syslog: block: mounting /dev/mtdblock4 (squashfs) as /mnt/mtdblock4 failed (-1) - Unknown error -1
    
95. Wed Aug 20 08:28:27 2014 user.notice ocserv: Generating CA certificate...
    
96. Wed Aug 20 08:28:33 2014 kern.info kernel: [   32.450000] device eth0.1 entered promiscuous mode
    
97. Wed Aug 20 08:28:33 2014 kern.info kernel: [   32.460000] device eth0 entered promiscuous mode
    
98. Wed Aug 20 08:28:33 2014 kern.info kernel: [   32.470000] br-lan: port 1(eth0.1) entered forwarding state
    
99. Wed Aug 20 08:28:33 2014 kern.info kernel: [   32.470000] br-lan: port 1(eth0.1) entered forwarding state
    
100. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'lan' is enabled
     
101. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'lan' is setting up now
     
102. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'lan' is now up
     
103. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'loopback' is enabled
     
104. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'loopback' is setting up now
     
105. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'loopback' is now up
     
106. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'wan' is enabled
     
107. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'wan' is setting up now
     
108. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Network device 'eth0' link is up
     
109. Wed Aug 20 08:28:33 2014 daemon.notice netifd: VLAN 'eth0.2' link is up
     
110. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'wan' has link connectivity
     
111. Wed Aug 20 08:28:33 2014 daemon.notice netifd: VLAN 'eth0.1' link is up
     
112. Wed Aug 20 08:28:33 2014 daemon.notice netifd: VLAN 'eth0.1' link is down
     
113. Wed Aug 20 08:28:33 2014 daemon.notice netifd: VLAN 'eth0.1' link is up
     
114. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Bridge 'br-lan' link is up
     
115. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'lan' has link connectivity
     
116. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Network device 'lo' link is up
     
117. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'loopback' has link connectivity
     
118. Wed Aug 20 08:28:33 2014 daemon.notice netifd: VLAN 'eth0.2' link is down
     
119. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'wan' has link connectivity loss
     
120. Wed Aug 20 08:28:33 2014 daemon.notice netifd: VLAN 'eth0.2' link is up
     
121. Wed Aug 20 08:28:33 2014 daemon.notice netifd: Interface 'wan' has link connectivity
     
122. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.110000] cfg80211: Calling CRDA for country: CN
     
123. Wed Aug 20 08:28:35 2014 daemon.notice netifd: wan (1662): udhcpc (v1.22.1) started
     
124. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.190000] cfg80211: Regulatory domain changed to country: CN
     
125. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.200000] cfg80211:  DFS Master region: FCC
     
126. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.200000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
     
127. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.210000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
     
128. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.220000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
     
129. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.230000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
     
130. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.230000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
     
131. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.240000] cfg80211:   (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
     
132. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.250000] cfg80211:   (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm), (N/A)
     
133. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.260000] cfg80211:   (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
     
134. Wed Aug 20 08:28:35 2014 kern.info kernel: [   34.470000] br-lan: port 1(eth0.1) entered forwarding state
     
135. Wed Aug 20 08:28:36 2014 daemon.notice netifd: wan (1662): Sending discover...
     
136. Wed Aug 20 08:28:37 2014 daemon.notice netifd: radio0 (1626): sh: acs_survey: bad number
     
137. Wed Aug 20 08:28:37 2014 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
     
138. Wed Aug 20 08:28:39 2014 daemon.notice netifd: wan (1662): Sending discover...
     
139. Wed Aug 20 08:28:39 2014 kern.info kernel: [   38.340000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
     
140. Wed Aug 20 08:28:39 2014 kern.info kernel: [   38.380000] device wlan0 entered promiscuous mode
     
141. Wed Aug 20 08:28:42 2014 daemon.notice netifd: wan (1662): Sending discover...
     
142. Wed Aug 20 08:28:44 2014 daemon.info dnsmasq[1793]: started, version 2.71 cachesize 150
     
143. Wed Aug 20 08:28:44 2014 daemon.info dnsmasq[1793]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
     
144. Wed Aug 20 08:28:44 2014 daemon.info dnsmasq-dhcp[1793]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
     
145. Wed Aug 20 08:28:44 2014 daemon.info dnsmasq[1793]: using local addresses only for domain lan
     
146. Wed Aug 20 08:28:44 2014 daemon.warn dnsmasq[1793]: no servers found in /tmp/resolv.conf.auto, will retry
     
147. Wed Aug 20 08:28:44 2014 daemon.info dnsmasq[1793]: read /etc/hosts - 1 addresses
     
148. Wed Aug 20 08:28:44 2014 daemon.info dnsmasq-dhcp[1793]: read /etc/ethers - 0 addresses
     
149. Wed Aug 20 08:28:44 2014 user.notice upnp daemon: external interface not found, not starting
     
150. Wed Aug 20 08:28:49 2014 kern.info kernel: [   48.430000] br-lan: port 2(wlan0) entered forwarding state
     
151. Wed Aug 20 08:28:49 2014 kern.info kernel: [   48.430000] br-lan: port 2(wlan0) entered forwarding state
     
152. Wed Aug 20 08:28:49 2014 kern.info kernel: [   48.440000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
     
153. Wed Aug 20 08:28:50 2014 daemon.notice netifd: Network device 'wlan0' link is up
     
154. Wed Aug 20 08:28:51 2014 kern.info kernel: [   50.430000] br-lan: port 2(wlan0) entered forwarding state
     
155. Wed Aug 20 08:29:12 2014 user.notice ocserv: Generating server certificate...
     
156. Wed Aug 20 08:29:40 2014 authpriv.info dropbear[1941]: Not backgrounding
     
157. Wed Aug 20 08:29:41 2014 daemon.info ocserv[1965]: main: initialized ocserv 0.8.2
     
158. Wed Aug 20 08:29:41 2014 daemon.info ocserv[1967]: sec-mod: sec-mod initialized (socket: /var/lib/ocserv/ocserv-socket.1965)
     
159. Wed Aug 20 08:29:42 2014 user.info syslog: module is already loaded - xt_comment
     
160. Wed Aug 20 08:29:42 2014 kern.emerg already loaded - xt_comment
     
161. Wed Aug 20 08:29:44 2014 user.info syslog: module is already loaded - xt_comment
     
162. Wed Aug 20 08:29:44 2014 kern.emerg already loaded - xt_comment
     
163. Wed Aug 20 08:29:45 2014 user.emerg syslog: Generating RSA private key, 1024 bit long modulus
     
164. Wed Aug 20 08:29:46 2014 user.emerg syslog: Generating selfsigned certificate with subject 'C=DE;ST=Berlin;L=Berlin;CN=OpenWrt;' and validity 20140820002945-20160819002945
     
165. Wed Aug 20 08:29:47 2014 user.emerg syslog: touch: /var/run/vsftpd/vsftpd.conf: No such file or directory
     
166. Wed Aug 20 08:29:47 2014 user.emerg syslog: touch: /var/run/vsftpd/vusers.txt: No such file or directory
     
167. Wed Aug 20 08:29:47 2014 user.emerg syslog: touch: /var/run/vsftpd/vsftpd.vu: No such file or directory
     
168. Wed Aug 20 08:29:50 2014 user.emerg syslog: jffs2 is not ready - marker found
     
169. Wed Aug 20 08:29:50 2014 user.emerg syslog: jffs2 is not ready - marker found
     
170. Wed Aug 20 08:29:50 2014 kern.warn kernel: [  109.020000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
     
171. Wed Aug 20 08:29:50 2014 kern.warn kernel: [  109.020000] jffs2_build_filesystem(): unlocking the mtd device... done.
     
172. Wed Aug 20 08:30:09 2014 kern.info kernel: [  127.760000] rt305x-esw 10110000.esw: link changed 0x03
     
173. Wed Aug 20 08:30:10 2014 kern.warn kernel: [  109.030000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
     
174. Wed Aug 20 08:30:10 2014 kern.notice kernel: [  128.880000] jffs2: notice: (2250) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
     
175. Wed Aug 20 08:30:12 2014 user.emerg syslog: doing fo cleanup
     
176. Wed Aug 20 08:30:12 2014 user.emerg syslog: Shadowsocks is disabled.
     
177. Wed Aug 20 08:30:13 2014 user.emerg syslog: setting up led wifi
     
178. Wed Aug 20 08:30:13 2014 user.emerg syslog: setting up led USB
     
179. Wed Aug 20 08:30:13 2014 user.emerg syslog: setting up led wan
     
180. Wed Aug 20 08:30:13 2014 user.emerg syslog: 并发拨号已禁用
     
181. Wed Aug 20 08:30:13 2014 user.emerg syslog: 并发拨号已禁用
     
182. Wed Aug 20 08:30:14 2014 user.emerg syslog: - init complete -
     
183. Wed Aug 20 08:30:49 2014 kern.info kernel: [  168.150000] rt305x-esw 10110000.esw: link changed 0x03
     
184. Wed Aug 20 08:31:33 2014 daemon.debug ocserv[1965]: ctl: received request from pid 2324 and uid 0
     
185. Wed Aug 20 08:31:37 2014 daemon.debug ocserv[1965]: ctl: received request from pid 2354 and uid 0
     
186. Wed Aug 20 08:31:42 2014 daemon.debug ocserv[1965]: ctl: received request from pid 2383 and uid 0
     
187. Wed Aug 20 08:31:47 2014 daemon.debug ocserv[1965]: ctl: received request from pid 2412 and uid 0
     

复制代码

brya***

981213 发表于 2014-8-20 09:15
不好意思忘了装hub驱动……下一版会补上的……

您好！我想问一下，hub驱动需要装哪些包呢？谢谢！

zwweil***

给我个地址我送你台千兆WAN 的机器。

keji***

弱弱地问一句，百兆和千兆的uboot通用？