TL- WR882N ttl刷机 tpl 不能终止

宝***

TL- WR882N ttl刷机 tpl 不能终止

宝***

怎么代码发不了

宝***

1. U-Boot 1.1.4 (Nov 14 2013 - 19:26:49)
   
2. 
   
3. cus249 - Dragonfly 1.0
   
4. 
   
5. DRAM:  16 MB
   
6. Top of RAM usable for U-Boot at: 81000000
   
7. Reserving 130k for U-Boot at: 80fdc000
   
8. Reserving 132k for malloc() at: 80fbb000
   
9. Reserving 44 Bytes for Board Info at: 80fbafd4
   
10. Reserving 36 Bytes for Global Data at: 80fbafb0
    
11. Reserving 128k for boot params() at: 80f9afb0
    
12. Stack Pointer at: 80f9af98
    
13. Now running in RAM - U-Boot at: 80fdc000
    
14. Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x15
    
15. flash size 4MB, sector count = 1024
    
16. Flash:  4 MB
    
17. Using default environment
    
18. 
    
19. In:    serial
    
20. Out:   serial
    
21. Err:   serial
    
22. Net:   ath_gmac_enet_initialize...
    
23. No valid address in Flash. Using fixed address
    
24. No valid address in Flash. Using fixed address
    
25. ath_gmac_enet_initialize: reset mask:c02200
    
26. Dragonfly----> S27 PHY *
    
27. : cfg1 0x80000000 cfg2 0x7114
    
28. eth0: 00:03:7f:09:0b:ad
    
29. athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
    
30. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
    
31. eth0 up
    
32. ATHRS27: resetting s27
    
33. ATHRS27: s27 reset done
    
34. : cfg1 0x800c0000 cfg2 0x7214
    
35. eth1: 00:03:7f:09:0b:ad
    
36. athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
    
37. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
    
38. athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
    
39. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
    
40. athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
    
41. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
    
42. athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
    
43. athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
    
44. eth1 up
    
45. eth0, eth1
    
46. Setting 0x181162c0 to 0x53a62100
    
47. Autobooting in 1 seconds
    
48. header.file[0].offset=0x80, len=0x44660
    
49. header.file[1].offset=0x446e0, len=0x528
    
50. header.file[2].offset=0x44c10, len=0xc6ec7
    
51. header.file[3].offset=0x0, len=0x0
    
52. vxWorks.bin from =0x53c10, len=0xc6ec7
    
53. Uncompressing...ERROR: LzmaDecode.c, 543
    
54. 
    
55. Decoding error = 1
    
56. Error,can't load boot file!!

复制代码

宝***

哪位老大帮帮忙 指导下 已经弄了好几天了也没解决掉

宝***

有人吗？

power***

TTL刷机不会来着

宝***

没有能帮忙的吗？

chanw***

按ctrl +c  试试

vic***

使用putty试试，超级终端也试试。

hackp***

没硬改，只能刷原厂固件。
按tpl中止，可能要补电阻才能输入

宝***

hackpascal 发表于 2015-5-9 20:31
没硬改，只能刷原厂固件。
按tpl中止，可能要补电阻才能输入

目前tpl按键不能终止，需要补什么位置的的电阻，有相关的教程吗？