|
本帖最后由 ┽微距ペ 于 2015-8-18 16:52 编辑
- 本地连接填写了固定IP,任何状态显示网线被拔出,华硕的救援模式根本不行,显示找不到IP
复制代码- 下面来上TTL信息,就开机显示的信息。
- CFE version 5.100.127 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
- Build Date: 五 9月 14 17:47:35 CST 2012 (boyau@localhost)
- Copyright (C) 2000-2008 Broadcom Corporation.
- Init Arena
- Init Devs.
- Boot partition size = 262144(0x40000)
- CPU type 0x19749: 600MHz
- Tot mem: 131072 KBytes
- CFE mem: 0x80700000 - 0x80839350 (1282896)
- Data: 0x80733120 - 0x807363E0 (12992)
- BSS: 0x807363E0 - 0x80737350 (3952)
- Heap: 0x80737350 - 0x80837350 (1048576)
- Stack: 0x80837350 - 0x80839350 (8192)
- Text: 0x80700000 - 0x80733118 (209176)
- Committing NVRAM...done
- Null Rescue Flag.
- Loader:raw Filesys:tftp Dev:(null) File:: Options:(null)
- Loading: TFTP Server.
- Failed.
- Could not load :: Error
- Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
- Loading: .. 3916 bytes read
- Entry at 0x80001000
- Starting program at 0x80001000
- Linux version 2.6.24.111 (root@dd-wrt.buildserver) (gcc version 4.1.2) #21129 Mon Jun 23 01:24:19 CEST 2014
- CPU revision is: 00019749
- Determined physical RAM map:
- memory: 07fff000 @ 00000000 (usable)
- memory: 08000000 @ 87fff000 (usable)
- Zone PFN ranges:
- Normal 0 -> 131072
- HighMem 131072 -> 589823
- Movable zone start PFN for each node
- early_node_map[2] active PFN ranges
- 0: 0 -> 32767
- 0: 557055 -> 589823
- Built 1 zonelists in Zone order. Total pages: 65535
- Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd
- Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
- Primary data cache 32kB, 4-way, linesize 32 bytes.
- Synthesized TLB refill handler (20 instructions).
- Synthesized TLB load handler fastpath (32 instructions).
- Synthesized TLB store handler fastpath (32 instructions).
- Synthesized TLB modify handler fastpath (31 instructions).
- PID hash table entries: 512 (order: 9, 2048 bytes)
- CPU: BCM5300 rev 1 at 600 MHz
- Using 300.000 MHz high precision timer.
- console [ttyS0] enabled
- Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
- Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
- Memory: 252940k/131068k available (3490k kernel code, 8904k reserved, 1369k data, 188k init, 131072k highmem)
- Mount-cache hash table entries: 512
- NET: Registered protocol family 16
- Generic PHY: Registered new driver
- PCI: Initializing host
- PCI: Reset RC
- PCI: Initializing host
- PCI: Reset RC
- PCI: Fixing up bus 0
- PCI/PCIe coreunit 0 is set to bus 1.
- PCI: Fixing up bridge
- PCI: Fixing up bridge
- PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
- PCI: Fixing up bus 1
- PCI/PCIe coreunit 1 is set to bus 2.
- PCI: Fixing up bridge
- PCI: Fixing up bridge
- PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
- PCI: Fixing up bus 2
- NET: Registered protocol family 2
- Time: MIPS clocksource has been installed.
- IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- TCP established hash table entries: 4096 (order: 3, 32768 bytes)
- TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
- TCP: Hash tables configured (established 4096 bind 4096)
- TCP reno registered
- highmem bounce pool size: 64 pages
- devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
- devfs: boot_options: 0x1
- squashfs: version 3.0 (2006/03/15) Phillip Lougher
- io scheduler noop registered
- io scheduler deadline registered (default)
- HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
- N_HDLC line discipline registered.
- Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
- serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
- serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
- PPP generic driver version 2.4.2
- PPP Deflate Compression module registered
- PPP BSD Compression module registered
- MPPE/MPPC encryption/compression module registered
- NET: Registered protocol family 24
- tun: Universal TUN/TAP device driver, 1.6
- tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
- et_module_init: passivemode set to 0x0
- PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
- PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
- Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002201
- Amd/Fujitsu Extended Query Table at 0x0040
- Physically mapped flash: CFI does not contain boot bank location. Assuming top.
- number of CFI chips: 1
- cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
- Flash device: 0x2000000 at 0x1c000000
- bootloader size: 262144
- nvram size: 32768
- Physically mapped flash: Filesystem type: squashfs, size=0x20e376
- partition size = 2238052
- Creating 5 MTD partitions on "Physically mapped flash":
- 0x00000000-0x00040000 : "cfe"
- 0x00040000-0x01fe0000 : "linux"
- 0x0019d99c-0x003c0000 : "rootfs"
- mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
- 0x01fe0000-0x02000000 : "nvram"
- 0x003c0000-0x01fe0000 : "ddwrt"
- Found a 0MB serial flash
- sflash: found no supported devices
- Broadcom Watchdog Timer: 0.07 initialized.
- u32 classifier
- Performance counters on
- Actions configured
- Netfilter messages via NETLINK v0.30.
- nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
- ctnetlink v0.93: registering with nfnetlink.
- IPv4 over IPv4 tunneling driver
- GRE over IPv4 tunneling driver
- ip_tables: (C) 2000-2006 Netfilter Core Team
- ClusterIP Version 0.8 loaded successfully
- TCP bic registered
- TCP cubic registered
- TCP westwood registered
- TCP highspeed registered
- TCP hybla registered
- TCP htcp registered
- TCP vegas registered
- TCP scalable registered
- NET: Registered protocol family 1
- NET: Registered protocol family 17
- Welcome to PF_RING 3.2.1
- (C) 2004-06 L.Deri <deri@ntop.org>
- NET: Registered protocol family 27
- PF_RING: bucket length 128 bytes
- PF_RING: ring slots 4096
- PF_RING: sample rate 1 [1=no sampling]
- PF_RING: capture TX No [RX only]
- PF_RING: transparent mode Yes
- PF_RING initialized correctly.
- PF_RING: registered /proc/net/pf_ring/
- 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
- All bugs added by David S. Miller <davem@redhat.com>
- decode 1f02
- VFS: Mounted root (squashfs filesystem) readonly.
- Mounted devfs on /dev
- Freeing unused kernel memory: 188k freed
- start service
- starting Architecture code for broadcom
- done
- get_wl_instance doesnt return the right value 0
- No such device
- Booting device: Linksys WRT54G/GL/GS
- roboswitch: Probing device eth0: No such device
- roboswitch: Probing device eth1: No such device
- roboswitch: Probing device eth2: No such device
- roboswitch: Probing device eth3: No such device
- boardflags are 0x0388
- /bin/sh: can't create /proc/switch/eth0/reset: nonexistent directory
- /bin/sh: can't create /proc/switch/eth0/enable_vlan: nonexistent directory
- /bin/sh: can't create /proc/switch/eth0/vlan/0/ports: nonexistent directory
- /bin/sh: can't create /proc/switch/eth0/vlan/1/ports: nonexistent directory
- /etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
- /etc/preinit: line 44: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
- get_wl_instance doesnt return the right value 0
- /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
- /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
- /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
- get_wl_instance doesnt return the right value 0
- wl:-i down ->wl driver adapter not found
- Write wireless mac fail : : No such device
- wl:-i up ->wl driver adapter not found
- br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
- /bin/sh: can't create /sys/devices/virtual/net/br0/bridge/multicast_snooping: nonexistent directory
- device br0 entered promiscuous mode
- device br0 left promiscuous mode
- device br0 entered promiscuous mode
- device br0 left promiscuous mode
- get_wl_instance doesnt return the right value 0
- wl:-i vlan_mode 0 ->wl driver adapter not found
- get_wl_instance doesnt return the right value 0
- wl:-i radio on ->wl driver adapter not found
- function start_hwmon not found
- SIOCGIFFLAGS: No such device
- get_wl_instance doesnt return the right value 0
- wl:-i radio on ->wl driver adapter not found
- get_wl_instance doesnt return the right value 0
- No such device
- /bin/sh: can't create /proc/sys/net/ipv4/conf/br0/loop: nonexistent directory
- Bad argument `MARK'
- Error occurred at line: 4
- Try `iptables-restore -h' or 'iptables-restore --help' for more information.
- /bin/sh: can't create /proc/sys/net/ipv4/netfilter/ip_conntrack_udp_timeouts: nonexistent directory
- /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
- /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
- /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
- get_wl_instance doesnt return the right value 0
- No such device
- get_wl_instance doesnt return the right value 0
- No such device
- get_wl_instance doesnt return the right value 0
- No such device
- get_wl_instance doesnt return the right value 0
- No such device
- /bin/sh: /opt/etc/init.d/rcS: not found
- /bin/sh: /jffs/etc/init.d/rcS: not found
- /bin/sh: /mmc/etc/init.d/rcS: not found
- get_wl_instance doesnt return the right value 0
- No such device
- get_wl_instance doesnt return the right value 0
- No such device
- get_wl_instance doesnt return the right value 0
- No such device
- 按回车能登陆DDWRT
- No such device
- ==========================================================
- ____ ___ __ ______ _____ ____ _ _
- | _ \| _ \ \ \ / / _ \_ _| __ _|___ \| || |
- || | || ||____\ \ /\ / /| |_) || | \ \ / / __) | || |_
- ||_| ||_||_____\ V V / | _ < | | \ V / / __/|__ _|
- |___/|___/ \_/\_/ |_| \_\|_| \_/ |_____| |_|
- DD-WRT v24-sp2
- http:// www. dd-wrt.com
- ==========================================================
- Jan 1 00:01:41 login[1036]: root login on 'console'
- BusyBox v1.22.1 (2014-06-23 01:21:20 CEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- root@DD-WRT:~#
- root@DD-WRT:~# get_wl_instance doesnt return the right value 0
- No such device
- 但老出现
- get_wl_instance doesnt return the right value 0
-
-
- 以上是自动开机出来的信息,下面是按住ctrl+c的信息
- CFE version 5.100.127 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
- Build Date: 五 9月 14 17:47:35 CST 2012 (boyau@localhost)
- Copyright (C) 2000-2008 Broadcom Corporation.
- Init Arena
- Init Devs.
- Boot partition size = 262144(0x40000)
- CPU type 0x19749: 600MHz
- Tot mem: 131072 KBytes
- CFE mem: 0x80700000 - 0x80839350 (1282896)
- Data: 0x80733120 - 0x807363E0 (12992)
- BSS: 0x807363E0 - 0x80737350 (3952)
- Heap: 0x80737350 - 0x80837350 (1048576)
- Stack: 0x80837350 - 0x80839350 (8192)
- Text: 0x80700000 - 0x80733118 (209176)
- Committing NVRAM...done
- Startup canceled
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE> ^C
- CFE>
- 输入TFTPD出现如下情况
- CFE> tftpd
- Invalid command: "tftpd"
- Available commands: et, show, nvram, reboot, flash, batch, go, boot, load, save, ping, arp, ifconfig, help
- *** command status = -1
- 输入nvram erase出现如下信息
- CFE> nvram erase
- *** command status = 0
复制代码
|
|