找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 3299|回复: 2

TP-WA801N V2 TTL 登录的问题

[复制链接]
发表于 2015-9-17 16:38 | 显示全部楼层 |阅读模式
TP-WA801N V2.1 不小心刷了中文官网的最“新”固件,如图
死机依旧,于是打算刷成别的固件,可是悲剧的是各种固件,用TPRouter改的,说是型号不符;英文官网下的,说是版本过低(英文官网有15年的,中文官网上是13年的……)


于是打算思考TTL刷机,过程如下,请问我哪个地方做得不对?谢谢!
过程分普通启动和按了Ctrl+C启动两种

----------------------------------分割线---------------------------

普通的启动以后,root用了password, 5up, admin,还有我自己设的123!qwe都登录不了,如下:

                       Y
                        b傚+j夾]譑浇鬦k?蕗甐焦?H?莜W溯牃+荪
                                                              袮?拏皞犻矋!偟k絤爱V愆雭KK褷?荪虍     﨩?揥裳╇乲ギk駹缮j奀酈腭╇丄传升?Ie?)峀inux version 2.6.31--LSDK-9.2.0_U5.508 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #16 Mon Jun 17 18:39:55 CST 2013
flash_size passed from bootloader = 4
Ram size passed from bootloader =33554432
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 535 ddr 400 ahb 200
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(art) mem=32M
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 30132k/32768k available (1718k kernel code, 2636k reserved, 430k data, 112k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 267.26 BogoMIPS (lpj=534528)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "art"
->Oops: flash id 0x1c3016 .
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 112k freed
init started:  BusyBox v1.01 (2013.05.24-01:47+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (512 buckets, 5120 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/af_key.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xfrm_user.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/xt_mark.ko': No such file or directory

Now flash open!
Now flash open!
(none) mips #16 Mon Jun 17 18:39:55 CST 2013 (none)
(none) login: ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:1 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2D82
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:0 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2582
athr_gmac_ring_alloc Allocated 640 at 0x81e26c00
athr_gmac_ring_alloc Allocated 2048 at 0x81ccb000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
athr_gmac_ring_alloc Allocated 640 at 0x81e26800
athr_gmac_ring_alloc Allocated 2048 at 0x81e2a800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
ATHRS27: resetting s27
ATHRS27: s27 reset done
Setting PHY...
device eth1 entered promiscuous mode
Now flash open!
athr_gmac_ring_free Freeing at 0x81e26c00
athr_gmac_ring_free Freeing at 0x81ccb000
athr_gmac_ring_alloc Allocated 640 at 0x81e26c00
athr_gmac_ring_alloc Allocated 2048 at 0x81ea5800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
asf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Restoring Cal data from Flash
ath_get_caps[5106] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5081] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
====>>>>SystemMode : Standard AP
wlan_vap_create : enter. devhandle=0x81fe42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x81fe42c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created
====>>>>wlan: rand channel 11


DES SSID SET=TP-LINK_07C7FC
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1


***********************************
athr_gmac_ring_free Freeing at 0x81e26c00
athr_gmac_ring_free Freeing at 0x81ea5800
br0: port 1(eth1) entering disabled state
athr_gmac_ring_alloc Allocated 640 at 0x81e26c00
athr_gmac_ring_alloc Allocated 2048 at 0x81ea5000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...


***********************************
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1
br0: port 2(ath0) entering disabled state

DES SSID SET=TP-LINK_07C7FC


***********************************
br0: port 2(ath0) entering forwarding state
====>>>>cmdCtrl open success
====>>>>eventCtrl open success
====>>>>eventCtrl attach success
ATHR_GMAC: GE0 RX DMA ENABLE

TL-WA801N mips #16 Mon Jun 17 18:39:55 CST 2013 (none)
TL-WA801N login: root
Password:


----------------------------------分割线---------------------------

于是我搜到网上说,在启动的时候按TPL或者Ctrl+C,还是进入不了 CFE,过程如下:
          魽H?AE?Q叺
                      氁愠ぜ耀敝?倁餋?
                                       b俥?*
                                             乚譑給?k仼
                                                        妭硻蟠C醿$浇鬦ki[潟 X蔲捖悅犐蒵?俇铎験甆溯營佶
                                                                                                           J酢V虍       﨩婥(艆r藵 -柟e
Linux version 2.6.31--LSDK-9.2.0_U5.508 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #16 Mon Jun 17 18:39:55 CST 2013         矌﹫
flash_size passed from bootloader = 4
Ram size passed from bootloader =33554432
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 535 ddr 400 ahb 200
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(art) mem=32M
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 30132k/32768k available (1718k kernel code, 2636k reserved, 430k data, 112k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 267.26 BogoMIPS (lpj=534528)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "art"
->Oops: flash id 0x1c3016 .
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 112k freed
init started:  BusyBox v1.01 (2013.05.24-01:47+0000) multi-call binary
^C
(none) mips #16 Mon Jun 17 18:39:55 CST 2013 (none)
(none) login: root
Password:
Login incorrect
(none) login: root
Password:
Login incorrect
(none) login: root
Password:
Login incorrect
Jan  1 00:00:39 login[123]: invalid password for `root' on `ttyS0'


(none) mips #16 Mon Jun 17 18:39:55 CST 2013 (none)
(none) login:

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
发表于 2016-11-6 09:09 | 显示全部楼层
?训ap-tXj拪-g鱇耲并-2?Bj卹 2窉倞?- 睋偸覛2)C?ㄕ浇?AP宝?圛5?
.?H鳺as饖r歫
wa.}憫蒧inZW+饼conVk〔睯?:呁?(16??ddr盝攻?
TX乿岖晛sele鉝? 0x孚義? 屡f軨酳etW藵?xb8LL撌?to倄2?2洳5
j        5
prY?:? t "懮 te?祽 in?殨峯nd簌burnZk乼est?+濋<NU淌j
FlX. j卬ufJ憗0xef?曎?eI?偮?, 腨Wk旾d1倄1稢?漣cm岖j2盿sh殽闀?MB        殨嵮or ?寡= 1&j
+汀i  8j        5?%%簠蒼inj卍 C?        ?ス?defX]媮envi?禃箃
奀?**%%%III蒖B吷戄are'U寻?倣夐D Bo恣RR?*?%III?%%%III蒖R? 缯?卹dV?'R?*%%%III蒵
Har朥?
In:? 骙??
O鯒殨丧al
奞.??s瀹+?
Ne?
濆3磢暪晅_i頩W+眎ze缮j婈 矃lid燲柹晄s ?2眳sh.?ス?fi晳佱曂s
?矃眎d X曂s i 2眳蚳. U??fi鳼
慸re螽H?w???曆mas-?殮00燙醀A?jjj? 应?Y
?櫇1 0?0皞倐殭澤 0x7LLSH鴈t枰倐?3?偸:0b?5??挄潄?褋
eth0燷5
UMA?---係2?e?
:櫇?0xf殭澤 0x7Βj
ethL'倐?3簱杺室0b篨VHh? 験J筰t +箒崱Q!IS27簰曂晅ti?毶7
ATH??s27挄蜁?do?
e??
e b*选?
b?+穗乫l釚鈘ULL>C酨r瀹.倕ssw?⒔ ab?
誸ob雼侀 ?殨嵔箲eth0?弓乨ow獺eth1?弓乨ow獺bur+藵乼est脖厺:<N諍蔶
## 码靴筭 i鞽謥at 9獋倐0 .嫂
?J祬ge *禃?  LZ?並ernY J祬ge
!蒭a鬥?? ?姠j?-?氁01??C
?I鞽謥Type'j%PS *苏?Ker?伾[XV耹z[X降pre?枼
  "呇?SizY'99巢?逖曂= 9r?Z        5妭 L+憗?枙蛃: 競倰倐0
!*箃ry渐寡:  ?f砐j
   U枼欏ing?嵀sum娧伆錰癕偄?..甇K
 U瞵?蒭ss殡並Y.?Im酼rrr OK
崱*W蓆inZ暽筫l 缮j奀酈ooW藵丄th瀹k丄R93?
Linux version 2.6.31--LSDK-9.2.0_U10.1020 (zhanghaozhong@wireless-2) (gcc version 4.3.3 (GCC) ) #gw-ap-ta40-1.0 Thu Mar 27 11:01:06 CST 2014
flash_size passed from bootloader = 8
arg 1: console=ttyS0,115200
arg 2: root=31:03
arg 3: rootfstype=squashfs
arg 4: init=/sbin/init
arg 5: mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),1280k(uImage),1152k(version_simple),5120k(version_full),64k(nvram),64k(nvram-bak),128k(jffs2),64k(ART)
arg 6: mem=63M
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 535 ddr 400 ahb 200
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00003f00
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16002
Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),1280k(uImage),1152k(version_simple),5120k(version_full),64k(nvram),64k(nvram-bak),128k(jffs2),64k(ART) mem=63M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 60992k/64512k available (2009k kernel code, 3444k reserved, 599k data, 160k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Console: colour dummy device 80x25
Calibrating delay loop... 266.24 BogoMIPS (lpj=133120)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.12)
msgmni has been set to 119
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
brd: module loaded
9 cmdlinepart partitions found on MTD device ath-nor0
Creating 9 MTD partitions on "ath-nor0":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000050000 : "u-boot-env"
0x000000050000-0x000000190000 : "uImage"
0x000000190000-0x0000002b0000 : "version_simple"
0x0000002b0000-0x0000007b0000 : "version_full"
0x0000007b0000-0x0000007c0000 : "nvram"
0x0000007c0000-0x0000007d0000 : "nvram-bak"
0x0000007d0000-0x0000007f0000 : "jffs2"
0x0000007f0000-0x000000800000 : "ART"
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 160k freed

init started:  BusyBox v1.01 (2013.09.12-19:03+0000) multi-call binary
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:100
ATHR_GMAC: Mac address for unit 0:bf7f0000
ATHR_GMAC: ff:ff:ff:ff:ff:ff
mac:0 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2580
ATHR_GMAC: RX TASKLET - Pkts per Intr:100
ATHR_GMAC: Mac address for unit 1:bf7f0006
ATHR_GMAC: ff:ff:ff:ff:ff:ff
mac:1 Registering S27....
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   40
ATHR_GMAC: Max rx descriptor count :   128
ATHR_GMAC: Mac capability flags    :   2D80
ath_wdt_init: Registering WDT success
athr_gmac_ring_alloc Allocated 640 at 0x83a25000
athr_gmac_ring_alloc Allocated 2048 at 0x8390c000
ATHRS27: resetting s27
ATHRS27: s27 reset done
Setting PHY...
athr_gmac_ring_alloc Allocated 640 at 0x83a25400
athr_gmac_ring_alloc Allocated 2048 at 0x83a29800
Setting PHY...
/etc/rc.d/run_normal_mod.sh: 46: multicast: not found
Gpioex begin.
state set.
mode set begin.
button: Unknown symbol ap_netlink_send
insmod: cannot insert `/lib/modules/button.ko': Unknown symbol in module (-1): No such file or directory
Not reserve ram for blackbox!

PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
/usr/sbin/startup: 85: cannot create /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_established: Directory nonexistent
insmod: cannot open module `/lib/modules/bridge.ko': No such file or directory
insmod: cannot open module `/lib/modules/flowctrl.ko': No such file or directory
user_file_writepen userfile error
record_hardreboot, open file(/proc/userfile) error.
cat: /tmp/rebootrecord: No such file or directory
cat: /tmp/rebootrecord: No such file or directory
cat: /tmp/rebootrecord: No such file or directory
cat: /tmp/rebootrecord: No such file or directory
cat: /tmp/rebootrecord: No such file or directory
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
Set OK!
athr_gmac_ring_free Freeing at 0x83a25400
athr_gmac_ring_free Freeing at 0x83a29800
athr_gmac_ring_free Freeing at 0x83a25000
athr_gmac_ring_free Freeing at 0x8390c000
athr_gmac_ring_alloc Allocated 640 at 0x83a25000
athr_gmac_ring_alloc Allocated 2048 at 0x8390c000
Setting PHY...
athr_gmac_ring_alloc Allocated 640 at 0x83a25400
athr_gmac_ring_alloc Allocated 2048 at 0x83a7a800
Setting PHY...
record_hardreboot, open file(/proc/userfile) error.
Modify passwd for useradmin success!
Create useradmin success!
Modify passwd for cmccadmin success!
Create cmccadmin success!


BusyBox v1.01 (2013.09.12-19:03+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

~ #
回复 支持 反对

使用道具 举报

发表于 2016-11-7 11:59 | 显示全部楼层
TP的也可以刷机吗
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-6-6 05:26

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表