|
|
这个是买来的板子，看着做工不错就留下了，但是不能用，跟着论坛的朋友思考刷机，估计找不到。某宝上了TTL转USB的线读出以下数据，前辈帮忙看看是否还有价值？谢谢啦！
Need to run mknod ...
SAGEMCOM Modified SPI Driver is initialized Successfully...
### GPIO Alternate function mode for SLIC: ENABLED
[HAL-BSP]: Load ...
[HAL-BSP]: Manufacturer(Sagemcom) Serial Number(LK12345DP123456)
[HAL-BSP]: Sagem Hardware ProductId(Sagemcom3965_generic) Version(S.5.0) Revision(1.0)
[HAL-BSP]: Customer Hardware ProductId(Sagemcom) Version(G22005010) Revision(S.5.0)
[HAL-BSP]: Firmware Version(france) Type(Unknown Firmware Type)
[HAL-BSP]: Size {Ram -> [Pp(131072) Linux(118100)] Flash ->[Pp(131072)]}
[HAL-BSP]: Ok ...
Found Atheros 8327revB switch hardware
fusiv_reg_miidev:1941 : 0x8583da00 (p=0)
Athr83xx Swith registration with eth0 Succeeded
Atheros 83xx switch registered to ethernet port eth0
ath_hal: 0.9.17.1 (AR5416, AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, AR5416_ISR_READ_CLEAR_SUPPORT, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_pci: 9.2.0_U9.915 (Atheros/multi-bss)
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
ar9300RadioAttach: Need analog access recipe!!
dfs_attach: use DFS enhancements
DFS min filter rssiThresh = 18
DFS max pulse dur = 151 ticks
ath_get_caps[4950] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[4925] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9380: mem=0x1a000000, irq=32 hw_base=0xba000000
PCI: Enabling device 0001:01:00.0 (0000 -> 0002)
__ath_attach: Set global_scn[1]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
ar9300RadioAttach: Need analog access recipe!!
dfs_attach: use DFS enhancements
DFS min filter rssiThresh = 18
DFS max pulse dur = 151 ticks
ath_get_caps[4950] rx chainmask mismatch actual 7 sc_chainmak 0
ath_get_caps[4925] tx chainmask mismatch actual 7 sc_chainmak 0
wifi1: Atheros 9580: mem=0x1b000000, irq=33 hw_base=0xbb000000
atheros ar8327 (isis) detected
#############################################
initializing SSDK functions...
########ssdk_init complete success.##########
IGMP Snoop Module inserted successfully
Driver LED and BUTTON init .....
Driver LED and BUTTON ok .....
***** PPP over Ethernet Relay driver registered with Major number: 251 *****
VDSL PHY default parameters configured successfully
default parameters configured successfully
VDSL link parameters set
Reseting ATM Cell Header RAM...
ATM Driver Initialized SUCCESSFULLY...
***********************************************************
Using: Software Build(voice_2_6 : V2 VOICE ARCHITECTURE)
***********************************************************
NTR DIV Factor = 55
NTR Frame sync width is set to [4] SCLK cycles of 4.096 MHz
Power down, Power Up DSPs....
Could not find DSP configuration file, setting to defaults
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Save and reboot the system to effect the Codec Mode : 2
Registering Call Back Handlers
Configuring SCLK and FS as external, using NTR Clock/FS
DSP CLock Assigned:255
DSP SPORT Control Reg Assigned:820f
ADSP218x DOWNLOAD DONE !!!!
DSP Ver No:1.1
ADSP218x DOWNLOAD DONE !!!!
DSP Ver No:1.1
Initializing SLIC and VOICE Wait Queues
Initializing Voice
Fusiv Chipset = VX185, ChipID = 30200
Issuing HW Reset to SLIC using GPIO3
Issuing HW Reset to SLIC using GPIO4
SPI BAUD for SLIC Device: 0x10
Fusiv Chipset = VX185, ChipID = 30200
Issuing HW Reset to SLIC using GPIO3
Issuing HW Reset to SLIC using GPIO4
Assuming SLIC card as SILABS Si3217
Initializing SLICs
Silabs Si3217 code
Country use for SLIC FRANCE
ERROR SLIC IS NOT A SI3217x read 7
Silabs Si3217 code
Country use for SLIC FRANCE
ERROR SLIC IS NOT A SI3217x read 7
slicHandlers.fxoChipType:16
Silabs FXO - Si3050
FXO Initialized Successfully
Activate SLICs FXS => 2 FXO=>1
Issuing HW Reset to DECT using GPIO2
SPI BAUD for DECT Device:0xfa
Enable IRQ for DSP
Enable IRQ for DSP
Enable IRQ for DSPDVE
Enable IRQ for DSP DEC
MAX_SLIC_CHANNELS = 6
NUM_FXO_CHANNELS = 1
DSP System Initialized Successfully
Starting Kernel RTP Thread
RTP Kernel Thread Started
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
unionfs: new lower inode mtime (bindex=1, name=etc)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
EHCI: Enabling USB clocks and USB PHY reset
fusiv-ehci-hcd fusiv-ehci-hcd.0: Ikanos On-Chip EHCI Host Controller
fusiv-ehci-hcd fusiv-ehci-hcd.0: new USB bus registered, assigned bus number 1
fusiv-ehci-hcd fusiv-ehci-hcd.0: irq 35, io mem 0x19120000
fusiv-ehci-hcd fusiv-ehci-hcd.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Ikanos On-Chip EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.28.8 ehci_hcd
usb usb1: SerialNumber: ikf71xx ehci
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
fusiv-ohci-hcd fusiv-ohci-hcd.0: Ikanos On-Chip OHCI Host Controller
fusiv-ohci-hcd fusiv-ohci-hcd.0: new USB bus registered, assigned bus number 2
fusiv-ohci-hcd fusiv-ohci-hcd.0: irq 34, io mem 0x19110000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: Ikanos On-Chip OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.28.8 ohci_hcd
usb usb2: SerialNumber: ikf71xx ohci
ahci ahci: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part
scsi0 : ahci
ata1: SATA max UDMA/133 irq 31
ata1: SATA link down (SStatus 0 SControl 310)
Setting framing mode to BYPASS, ADSL
CPE start address is af800000
Intializing BME 0
Intializing BME 1
ipos system initialized
BME 1 is coming up
b1p0 iposBmeStartBlk cmdtag 0 status: IN PROGRESS
cpe>
Transfer to SDRAM Successful
BmeHw: Downloading BME 1 software at af800000
Enabled clocks for BME and related modules
BmeHw: Bme 1 software code downloaded successfully
Programmed BME window registers sucessfully
BME out of reset
b1p0 iposBmeStartBlk cmdtag 0 status: COMPLETE
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
cpe>
b1p0 iposPeriodicReportEnable cmdtag 99 status: COMPLETE
cpe>
could not parse BME hardware version from string
Firmware-VTU-R:10.13.0.43_ENGIKF7185 Time Apr 10 2012, 00:37:42
RTOS Copyright MGC 2006 - Nucleus PLUS - v. 1.15
BME R:112
mkdir: can't create directory '/opt/conf': No such file or directory
Mount filesystem1
Mount filesystem2
Switch root file system to unionfs
Fri Jan 1 00:00:00 UTC 2010
=*=*=*= BSP MODULES LOADING =*=*=*= Fast3965 generic
Check restore default
Test code doesn't care about Bad reboot count =90
/etc/rc.common: .: line 6: can't open '/etc/gui-core.conf'
/etc/rc.common: line 98: scan_interfaces: not found
Loading defaults
Loading synflood protection
Adding custom chains
Loading zones
Loading forwardings
Loading redirects
Loading rules
Loading includes
Optimizing conntrack
Loading interfaces
/etc/rc.common: line 78: scan_interfaces: not found
mknod: /dev/fb0: File exists
**********************
Chip:VX185-SE Revision:B1
**********************
net.ipv6.conf.all.forwarding = 1
Default Link Type is ADSL; loading ATM driver
factory configuration
Trying ADSL configuration...
start ppp configuration
SSDK Init OK!
operate done.
*********************************************************************
Setting UP Voice on ADI Fusiv
Loading DSP Driver ..... .
vdsld is not yet started: No such file or directory
vdsld is not yet started: No such file or directory
vdsld is not yet started: No such file or directory
vdsld is not yet started: No such file or directory
vdsld is not yet started: No such file or directory
creating nodes
start sip configuration
vdsld is not yet started: No such file or directory
Set BME Serial : LK12345DP123456 generic 011613
vdsld is not yet started: No such file or directory
drv_gpio mknod
mknod: /dev/led: File exists
mknod: /dev/but1: File exists
mknod: /dev/but2: File exists
mknod: /dev/but3: File exists
mknod: /dev/but4: File exists
mknod: /dev/but5: File exists
mknod: /dev/but6: File exists
/etc/config/dslSavedConfig.conf file exists
Restoring last configuration
Please execute 'vdsl' in 3 seconds to enter into Supervisor mode
2
1
0
Changing port profile #2 BAND_PLAN=0x2 PTM MODE=0x0
OamoptionMask 3
optionMask 8
b1p0 iposBmeProvision cmdtag 0 status: IN PROGRESS
cpe> #########################################################
########### B M E D U M P ##################
#########################################################
Uploading Log from 0xa000a048 size 0xbb84:
............................................................................................................................................................................................
Done
Bme 1 version: Firmware-VTU-R:10.13.0.43_ENGIKF7185 Time Apr 10 2012, 00:37:42
RTOS Copyright MGC 2006 - Nucleus PLUS - v. 1.15
BME R:112
Ipos Version: 1 333 [0x801e7cd0] -> ######################################################
333 [0x801e7cc8] -> FATAL_ERROR: ### Error_Code: 307 ### (bme hbeat: 0x1)
333 [0x801e7cb0] -> ######################################################
333 [0x801e7a88] -> DMA 7 - 00000000 00000000 00000000 00000000
333 [0x801e7a88] -> DMA 6 - 00000000 00000000 00000000 00000000
333 [0x801e7a88] -> DMA 5 - 00000000 00000000 00000000 00000000
333 [0x801e7a88] -> DMA 4 - 00000000 00000000 00000000 00000000
333 [0x801e7a88] -> DMA 3 - 00000000 00000000 00000000 00000000
333 [0x801e7a88] -> DMA 2 - 00000000 00000000 00000000 00000000
333 [0x801e7a88] -> DMA 1 - 00000000 00000000 00000000 00000000
333 [0x801e7a88] -> DMA 0 - 00000000 80000000 802cf15c c8600400
333 [0x801e7a4c] -> FMC 0 - 0 0 0 0
333 [0x801e7a24] -> DMC 0 - 0 0 0 0
333 [0x801e79fc] -> RMC 0 - 0 0 0 0
178 [0x80171b58] -> init_agc_ife_param: port=0
178 [0x80224d7c] -> afe 0x0 not supported
178 [0x80222f78] -> W-afeRead:read failed reg: 0x 0 port: 0
178 [0x80222f50] -> W-drvAfe_CPE5:AFE: readDoneBit wait timedOut port: 0
90 [0x80224c48] -> $$$$$ updateAfeIfeVer: 1
88 [0x801e7c48] -> About to shut down w/ errno 307
88 [0x80225a80] -> W-drvAfe_CPE5:AFE Device ID 0x0 not supported
88 [0x80225a48] -> AFE Version[0] = 0x0 0x0
88 [0x80222f78] -> W-afeRead:read failed reg: 0x 0 port: 0
88 [0x80222f50] -> W-drvAfe_CPE5:AFE: readDoneBit wait timedOut port: 0
15 [0x80237eb4] -> REOC Task ID = 0x80329978
14 [0x80214720] -> EOC Task ID: 0x803298c0
14 [0x8014bff4] -> BitSwap tx & rx state init for all ports
1 [0x80212428] -> HPI: Init rxTaskID = 803293b8 rxSemID = 804602c8
1 [0x80212414] -> HPI: Init txTaskID = 80329300 txmsgQID = 8045fc0c txSemID = 80460278
1 [0x802059b4] -> OAMP: Initialized. taskID = 80329248 msgQID = 8045d9f8
0 [0x8022272c] -> TxConst: US Sample/Sync:4096 Tones:2048
0 [0x802225a4] -> TxConst: Mode:0x0 ports:4 ghs:0x1 IOP:0
0 [0x80222b5c] -> RxConst: NumTonesP2:11 NumBitableTones:2048
0 [0x80222ab4] -> RxConst: DS Sample/Sync:4096 Tones:2048
0 [0x802228cc] -> RxConst: Mode:0x0 ports:4 ghs:0x1 IOP:0
0 [0x802146a0] -> BME rev number 112
0 [0x8021c454] -> bFIFOBuffers 0x0x800de600
0 [0x8021c454] -> bFIFOBuffers 0x0x800dc600
0 [0x8021c454] -> bFIFOBuffers 0x0x800da600
0 [0x8021c454] -> bFIFOBuffers 0x0x800d8600
0 [0x8021c454] -> bFIFOBuffers 0x0x800d6600
0 [0x8021c454] -> bFIFOBuffers 0x0x800d4600
0 [0x8021c454] -> bFIFOBuffers 0x0x800d2600
0 [0x8021c454] -> bFIFOBuffers 0x0x800d0600
0 [0x8021c454] -> bFIFOBuffers 0x0x800ce600
0 [0x8021c454] -> bFIFOBuffers 0x0x800cc600
0 [0x8021c454] -> bFIFOBuffers 0x0x800ca600
0 [0x8021c454] -> bFIFOBuffers 0x0x800c8600
0 [0x8021c454] -> bFIFOBuffers 0x0x800c6600
0 [0x8021c454] -> bFIFOBuffers 0x0x800c4600
0 [0x8021c454] -> bFIFOBuffers 0x0x800c2600
0 [0x8021c454] -> bFIFOBuffers 0x0x800c0600
0 [0x8022ef78] -> DATA i:0 dest:0xb9478240 src:0x802d8aec len: 0x602
0 [0x8022eef0] -> loading RMC, Micro code migration on to xasm - Tue Apr 3 12:16:36 IST 2012 section rmc_init to 0xb94b8000
0 [0x8022eec0] -> CODE i:0 dest:0xb94b8000 src:0x802d9104 len: 0x1136
0 [0x80220124] -> DMC MAILBOX 1 : 0xb9421308
0 [0x80220100] -> DMC MAILBOX 0 : 0xb9421300
0 [0x802200d8] -> BFIFO SPLIT: (addr:0xb9464e00 size: 0x0
0 [0x802200a4] -> Init BFIFO, split = 0
0 [0x8021fe74] -> Init AFIFO
0 [0x8021fdd4] -> Init ZFIFO
0 [0x8021fd90] -> Init YFIFO, split = 0
0 [0x801e2028] -> Allocated 384 Number of Message Queues (80020000) for BME
0 [0x80214614] -> EVENTLOG: Initialized. Build time (Apr 10 2012 00:37:33)
#########################################################
#########################################################
BME has been declared as Crashed; Hence Rebooting the CPE
Reinitializing the system
b1p0 iposBmeResetBlk cmdtag 0 status: IN PROGRESS
cpe>
Transfer to SDRAM Successful
BmeHw: Downloading BME 1 software at af800000
Enabled clocks for BME and related modules
BmeHw: Bme 1 software code downloaded successfully
Programmed BME window registers sucessfully
BME out of reset
b1p0 iposBmeResetBlk cmdtag 0 status: COMPLETE
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
alm freq 20
status freq 30
b1p0 iposPeriodicReportEnable cmdtag 99 status: IN PROGRESS
cpe>
Unable to communicate with BME. Please check the hardware
|
|
/1 
IP卡
狗仔卡
发表于 2016-7-28 16:32
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡