设为首页收藏本站

简体中文 繁體中文 English 日本語 Deutsch 한국 사람 بالعربية TÜRKÇE português คนไทย

切换到窄版

 找回密码
 立即注册

QQ登录

只需一步，快速开始

搜索
恩山无线论坛»论坛 › 无线设备硬件相关板块 › 斐讯无线路由器以及其它斐迅网络设备 › K3C变砖，求助TTL修复，谢谢……
广告投放联系QQ68610888
12下一页
返回列表 发新帖
查看: 18993|回复: 29

[k3c] K3C变砖，求助TTL修复，谢谢……

[复制链接]
viru***
| 显示全部楼层 |阅读模式
本帖最后由 virus1999 于 2017-10-21 22:37 编辑

前段时间，看到K3C有官改固件的消息后，就入了一台，打算送给朋友作搬入新房用。到手web页面刷固件，使用正常。
但是过了两天后，发现有死机现象。重启后，好了。
因为是放公司，过了一个晚上，第二天开机，发现无法启动，红灯。网口灯先全闪，然后灭，循环。
长按reset，能进uboot。刷入官方固件，能选择，但一点上传，显示updating页面后，路由器马上重启，继续网口闪灭。
手贱又输入官改，情况相同。
刷K3C官改后，按提示，备份了MTD0-9，尝试输入MTD8，倒是可以上传，也显示updating，路由不会马上重启。
但是无效果，等几分钟后，断电开机，还是以上的故障。

paldier 帮忙看看呗……多谢多谢！
NAND是三星，如果修砖怎么修？
WinHex合成你做的固件先ttl刷进去，然后再恢复官方固件？

接TTL后，日志如下：

  2. ROM VER: 2.1.0
  3. CFG 0a
  4. B
  5. .
  6. .


  9. U-Boot 2010.06-00044-gb399a23-LANTIQ-v-2.3.136 (Jul 24 2017 - 10:45:54)

  11. interAptiv
  12. cps cpu/ddr run in 800/666 Mhz
  13. DRAM:  224 MiB
  14. NAND:  Could not find valid JEDEC parameter page; aborting
  15. NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
  16. 128 MiB
  17. Bad block table found at page 65408, version 0x01
  18. Bad block table found at page 65344, version 0x01
  19. nand_read_bbt: Bad block at 0x000004060000
  20. nand_read_bbt: Bad block at 0x000007fe0000
  21. In:    serial
  22. Out:   serial
  23. Err:   serial
  24. Net:   multi type
  25. Internal phy firmware version: 0x853c
  26. GRX500 Switch

  28. Type "run flash_nfs" to mount root filesystem over NFS


  31. Press press hardware button for more than 4 seconds to run web failsafe mode



  35. Catution: hardware button wasn't pressed or not long enough!
  36. Continuing normal boot...

  38. Hit any key to stop autoboot:  5  4  3  2  1  0
  39. Creating 1 MTD partitions on "nand0":
  40. 0x000001340000-0x000007f40000 : "mtd=8"
  41. UBI: attaching mtd1 to ubi0
  42. UBI: physical eraseblock size:   131072 bytes (128 KiB)
  43. UBI: logical eraseblock size:    126976 bytes
  44. UBI: smallest flash I/O unit:    2048
  45. UBI: VID header offset:          2048 (aligned 2048)
  46. UBI: data offset:                4096
  47. UBI: attached mtd1 to ubi0
  48. UBI: MTD device name:            "mtd=8"
  49. UBI: MTD device size:            108 MiB
  50. UBI: number of good PEBs:        863
  51. UBI: number of bad PEBs:         1
  52. UBI: max. allowed volumes:       128
  53. UBI: wear-leveling threshold:    4096
  54. UBI: number of internal volumes: 1
  55. UBI: number of user volumes:     6
  56. UBI: available PEBs:             461
  57. UBI: total number of reserved PEBs: 402
  58. UBI: number of PEBs reserved for bad PEB handling: 8
  59. UBI: max/mean erase counter: 74/11
  60. Volume bootcoreB found at volume id 5
  61. read 0 bytes from volume 5 to a0400000(buf address)
  62. Read [2666496] bytes
  63. Volume kernelB found at volume id 3
  64. read 0 bytes from volume 3 to 80800000(buf address)
  65. Read [3047424] bytes
  66. ## Booting kernel from Legacy Image at 80800000 ...
  67.    Image Name:   MIPS LTQCPE Linux-3.10.102
  68.    Created:      2017-07-24   2:57:15 UTC
  69.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  70.    Data Size:    3014592 Bytes = 2.9 MiB
  71.    Load Address: a0020000
  72.    Entry Point:  a002df00
  73.    Verifying Checksum ... OK
  74.    Uncompressing Kernel Image ... OK

  76. Starting kernel ...

  78. [    0.000000] Initializing cgroup subsys cpu

  80. [    0.000000] Linux version 3.10.102 (jenkins@soho02) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 SMP Mon Jul 24 10:56:42 CST 2017

  82. [    0.000000] TLBINV/F supported, config4=0xc0000000

  84. [    0.000000] TLBINV/F supported, config4=0xc0000000

  86. [    0.000000] SoC: GRX500 rev 1.2

  88. [    0.000000] GCMP present

  90. [    0.000000] L2-only SYNC available

  92. [    0.000000] bootconsole [early0] enabled

  94. [    0.000000] CPU0 revision is: 0001a120 (MIPS interAptiv)

  96. [    0.000000] Enhanced Virtual Addressing (EVA 1GB) activated

  98. [    0.000000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000

  100. [    0.000000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001

  102. [    0.000000] BEV Overlay segment = 0xb0000000, size = 0x10000000

  104. [    0.000000] segctr0 2d0a0a segctr1 40d020a segctr2 38004d

  106. [    0.000000] MIPS: machine is EASY350 ANYWAN (GRX350) Router model

  108. [    0.000000] CMP IOCU detected

  110. [    0.000000] Hardware DMA cache coherency disabled

  112. [    0.000000] Determined physical RAM map:

  114. [    0.000000]  memory: 0e000000 @ 20000000 (usable)

  116. [    0.000000] User-defined physical RAM map:

  118. [    0.000000]  memory: 0e000000 @ 20000000 (usable)

  120. [    0.000000] Initrd not found or empty - disabling initrd

  122. [    0.000000] reserving 18874368 bytes @ 6800a3c0 for CBM

  124. [    0.000000] reserving 8388608 bytes @ 6920a3c0 for CBM

  126. [    0.000000] Zone ranges:

  128. [    0.000000]   DMA      [mem 0x20000000-0x27ffffff]

  130. [    0.000000]   Normal   [mem 0x28000000-0x2dffffff]

  132. [    0.000000] Movable zone start for each node

  134. [    0.000000] Early memory node ranges

  136. [    0.000000]   node   0: [mem 0x20000000-0x2dffffff]

  138. [    0.000000] Detected 3 available secondary CPU(s)

  140. [    0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.

  142. [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

  144. [    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.

  146. [    0.000000] PERCPU: Embedded 7 pages/cpu @69bce000 s7936 r8192 d12544 u32768

  148. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 56896

  150. [    0.000000] Kernel command line: ubi.mtd=system_sw rootfsname=rootfsB ro rootfstype=squashfs do_overlay console=ttyLTQ0,115200 ethaddr=2C:B2:1A:3D:14:14 panic=1 mtdparts=17c00000.nand-parts:1m(uboot),256k(ubootconfigA),256k(ubootconfigB),256k(gphyfirmware),1m(calibration),16m(bootcore),256k(pro_info),256k(dev_info),108m(system_sw),-(res) init=/etc/preinit active_bank=B update_chk=2 maxcpus=4 pci=pcie_bus_perf pcie_force_gen1=on ethwan= ubootver=U-Boot-2010.06-00044-gb399a23-LANTIQ-v-2.3.136 mem=224M@512M

  152. [    0.000000] eth0 mac address 2C-B2-1A-3D-14-14

  154. [    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)

  156. [    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

  158. [    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

  160. [    0.000000] Writing ErrCtl register=00000000

  162. [    0.000000] Readback ErrCtl register=00000000

  164. [    0.000000] allocated 458752 bytes of page_cgroup

  166. [    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups

  168. [    0.000000] Memory: 189712k/229376k available (6396k kernel code, 39664k reserved, 2219k data, 340k init, 0k highmem)

  170. [    0.000000] Hierarchical RCU implementation.

  172. [    0.000000] NR_IRQS:527

  174. [    0.000000] GIC: present

  176. [    0.000000] EIC: off

  178. [    0.000000] GIC map size 263

  180. [    0.000000] gic: revision 3.0

  182. [    0.000000] CPU0: c0 status register 1100fc00

  184. [    0.000000] of_gic_init init done

  186. [    0.000000] CPU Clock: 800000000Hz  mips_hpt_frequency 400000000Hz

  188. [    0.000000] CBM Clock: 600000000Hz DDR Clock: 666666666Hz NGI Clock: 300000000Hz

  190. [    0.000000] clock event init done !

  192. [    0.000000] gptu_setup_clocksource: done !

  194. [    0.000000] Calibrating delay loop... 513.63 BogoMIPS (lpj=2568192)

  196. [    0.070000] pid_max: default: 32768 minimum: 301

  198. [    0.070000] Mount-cache hash table entries: 512

  200. [    0.080000] Initializing cgroup subsys memory

  202. [    0.080000] size of core = 336, MAXCORE = 2 , MAXCPU = 4, MAXTCS = 6 MAX_VPE = 2

  204. [    0.090000] [update_DB_from_DT]:[363], cpuid = 0 name = LINUX

  206. [    0.090000] [update_DB_from_DT]:[363], cpuid = 1 name = LINUX

  208. [    0.100000] [update_DB_from_DT]:[363], cpuid = 2 name = LINUX

  210. [    0.100000] [update_DB_from_DT]:[363], cpuid = 3 name = MPEFW

  212. [    0.110000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 1

  214. [    0.110000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 2

  216. [    0.120000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 3

  218. [    0.120000]

  220. [    0.120000] Initial ITC_Address_Map0 00000000

  222. [    0.130000]

  224. def ITC_Address_Map1 01200000

  226. new ITC_Address_Map1 0120fc00

  228. def ITC_Address_Map0 00000000

  230. new ITC_Address_Map0 1c300001

  232. ITC Init done on Core 0 on CPU 0 !!!

  234. [    0.140000] [vmb_cpu_alloc]:[624] CPU vpet.cpu_status = 11

  236. [    0.150000] [vmb_cpu_start]:[842]  vmb_fw_msg_t = a00000b8 cpu = 1 vmb_msg_size = b0 sizeof(VMB_fw_msg_t) = 168 sizeof(FW_vmb_msg_t) = 8 !!!!

  238. [gic_trigger]:[551] VMB_CPU_IPI1 - 20 CPU = 1


  241. Outside WAIT got IPI interrupt to launch from cpu 01

  243. MSG_ID = 01[    0.160000] [vmb_cpu_start]:[881] WAITING FOR RESPONSE vpet->v_wq.wakeup_vpe = 0 !!!!

  245. [    0.160000] TLBINV/F supported, config4=0xc0000000

  247. [    0.160000] TLBINV/F supported, config4=0xc0000000

  249. [    0.160000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.

  251. [    0.160000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

  253. [    0.160000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.

  255. [    0.160000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000

  257. [    0.160000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001

  259. [    0.160000] BEV Overlay segment = 0xb0000000, size = 0x10000000

  261. [    0.160000]

  263. [    0.160000] Initial ITC_Address_Map0 1c300001

  265. [    0.160000] ITC Memory is already initialised for Core 0 at address 1c300000 !!![    0.160000] CPU1 revision is: 0001a120 (MIPS interAptiv)



  269. [    0.220000] [vmb_cpu_active]:[268] action = 10 , cpu = 1

  271. [    0.220000] [vmb_cpu_start]:[898] OUTSIDE WAIT wakeup_vpe = 1 vpet->fw_vmb.status = 1 ACK = 1 cpu = 1 ret1 = 9995 vpet = 608e3a98, smp_processor_id() = 0 , vpet->fw_vmb =608e3ac4 !!!!

  273. [    0.220000]  [vmb_cpu_start]:[905]  ret = 1



  277. [    0.230000] Synchronize counters for CPU 1: done.

  279. [    0.230000] GPTC clock event init on cpu: 1

  281. [    0.230000] clock event init done !

  283. [    0.240000] [vmb_cpu_alloc]:[624] CPU vpet.cpu_status = 11

  285. [    0.240000] [vmb_cpu_start]:[842]  vmb_fw_msg_t = a0000168 cpu = 2 vmb_msg_size = b0 sizeof(VMB_fw_msg_t) = 168 sizeof(FW_vmb_msg_t) = 8 !!!!

  287. [gic_trigger]:[555] VMB_CPU_IPI2 - 21 CPU = 2


  290. Outside WAIT got IPI interrupt to launch from cpu 02

  292. MSG_ID = 01[    0.250000] [vmb_cpu_start]:[881] WAITING FOR RESPONSE vpet->v_wq.wakeup_vpe = 0 !!!!

  294. [    0.250000] TLBINV/F supported, config4=0xc0000000

  296. [    0.250000] TLBINV/F supported, config4=0xc0000000

  298. [    0.250000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.

  300. [    0.250000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes

  302. [    0.250000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.

  304. [    0.250000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000

  306. [    0.250000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001

  308. [    0.250000] BEV Overlay segment = 0xb0000000, size = 0x10000000

  310. [    0.250000]

  312. [    0.250000] Initial ITC_Address_Map0 00000000

  314. [    0.250000]

  316. [    0.250000] def ITC_Address_Map1 01200000

  318. [    0.250000] new ITC_Address_Map1 0120fc00

  320. [    0.250000] def ITC_Address_Map0 00000000

  322. [    0.250000] new ITC_Address_Map0 1c300001

  324. [    0.250000]  ITC Init done on Core 1 on CPU 2 !!!

  326. [    0.250000] CPU2 revision is: 0001a120 (MIPS interAptiv)



  330. [    0.310000] [vmb_cpu_active]:[268] action = 10 , cpu = 2

  332. [    0.310000] [vmb_cpu_start]:[898] OUTSIDE WAIT wakeup_vpe = 1 vpet->fw_vmb.status = 1 ACK = 1 cpu = 2 ret1 = 9995 vpet = 608e3b08, smp_processor_id() = 0 , vpet->fw_vmb =608e3b34 !!!!

  334. [    0.310000]  [vmb_cpu_start]:[905]  ret = 1



  338. [    0.320000] Synchronize counters for CPU 2: done.

  340. [    0.320000] GPTC clock event init on cpu: 2

  342. [    0.320000] clock event init done !

  344. [    0.330000] [smp_init]:[553] CPU3 shouldn't run LINUX as per DT (model) config

  346. [    0.330000] Brought up 3 CPUs

  348. [    0.350000] pinctrl core: initialized pinctrl subsystem

  350. [    0.350000] regulator-dummy: no parameters

  352. [    0.360000] NET: Registered protocol family 16

  354. [    0.360000] [gpio_xrx500] { xrx500_gpio_init : 407 }XRX500 GPIO Driver, (C) 2014 Lantiq Deutschland Gmbh

  356. [    0.370000] dma-grx500 1e300000.dma: DMA3 base address be300000 chained_irq 77 irq_base 447

  358. [    0.380000] dma-grx500 1e300000.dma: Init done - hw rev: A, ports: 1, channels: 64

  360. [    0.390000] dma-grx500 1c100000.dma: DMA2TX base address bc100000 chained_irq 75 irq_base 399

  362. [    0.400000] dma-grx500 1c100000.dma: Init done - hw rev: A, ports: 1, channels: 16

  364. [    0.400000] dma-grx500 1c200000.dma: DMA2RX base address bc200000 chained_irq 76 irq_base 415

  366. [    0.410000] dma-grx500 1c200000.dma: Init done - hw rev: A, ports: 1, channels: 32

  368. [    0.420000] dma-grx500 1a100000.dma: DMA1TX base address ba100000 chained_irq 73 irq_base 351

  370. [    0.430000] dma-grx500 1a100000.dma: Init done - hw rev: A, ports: 1, channels: 16

  372. [    0.430000] dma-grx500 1a200000.dma: DMA1RX base address ba200000 chained_irq 74 irq_base 367

  374. [    0.440000] dma-grx500 1a200000.dma: Init done - hw rev: A, ports: 1, channels: 12

  376. [    0.450000] [gptu] { gptu_probe : 297 }dev id 16b00000.gptu


  379. [    0.460000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded


  382. [    0.460000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded


  385. [    0.470000] gptu-xrx500 16b00000.gptu: gptu: 2 timers loaded

  387. [    0.470000] gptu driver init successfully


  390. [    0.480000] [gptu] { gptu_probe : 297 }dev id 16300000.gptu


  393. [    0.480000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded


  396. [    0.490000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded


  399. [    0.490000] gptu-xrx500 16300000.gptu: gptu: 2 timers loaded

  401. [    0.500000] gptu driver init successfully


  404. [    0.500000] dma0-grx500 16e00000.dma: base address b6e00000 chained_irq 72 irq_base 335

  406. [    0.510000] dma0-grx500 16e00000.dma: Init done - hw rev: A, ports: 4, channels: 16

  408. [    0.510000] [pinctrl_xrx500] { pinctrl_xrx500_probe : 1243 }disabling the BBSPI at top-mux

  410. [    0.520000] pinctrl-xrx500 pinctrl.4: Init done

  412. [    0.530000] !!!!!!! WAVE400 system registeration on AHB

  414. [    0.530000] MTLK_MEM_BAR1_START is 14000000

  416. [    0.540000] MTLK_MEM_BAR1_END is 147fffff

  418. [    0.540000] MTLK_WIRELESS_IRQ_IN_INDEX is 26

  420. [    0.540000] [cbm] { cbm_xrx500_probe : 5346 }2


  423. [    0.550000] Initializing TMU with Base Address=be700000: ...

  425. [    0.550000] TMU Initialization Done

  427. [    0.560000] [cbm] { init_fsqm_buf_standard : 655 }init fsqm std successfully

  429. [    0.560000] [cbm] { init_fsqm_buf_jumbo : 698 }init fsqm jbo successfully

  431. [    0.570000] [cbm] { init_fsqm : 581 }fsqm init successfully

  433. [    0.570000] [cbm] { init_cbm_basic : 771 }init basic CBM successfully

  435. [    0.580000] [cbm] { cbm_hw_init : 1946 }CBM HW init

  437. [    0.580000] [cbm] { setup_DMA_p2p : 4733 }setup_DMA_p2p executed

  439. [    0.590000] [cbm] { configure_ports : 5187 }configure_ports 7 1 0 0 8 2


  442. [    0.590000] [cbm] { configure_ports : 5154 }configure_ports 7 1 16 1 8 2


  445. [    0.600000] [cbm] { configure_ports : 5187 }configure_ports 8 1 15 0 8 2


  448. [    0.600000] [cbm] { configure_ports : 5154 }configure_ports 8 1 31 1 8 2


  451. [    0.610000] [cbm] { init_cbm_ls : 1124 }Load spreader init successfully

  453. [    0.610000] [cbm] { cbm_xrx500_probe : 5409 }CBM Clock: 600000000Hz

  455. [    0.620000] [cbm] { cbm_xrx500_probe : 5411 }EQM delay Enabled

  457. [    0.620000] [cbm] { cbm_xrx500_probe : 5477 }CBM: Init Done !!

  459. [    0.630000] PCI host bridge /ssx3@18000000/pcie@900000 ranges:

  461. [    0.630000]  MEM 0x00000000b8000000..0x00000000baffffff

  463. [    0.640000]   IO 0x00000000bb800000..0x00000000bb8fffff

  465. [    0.740000] PCIe LCPLL SSC Mode Enabled

  467. [    1.250000] pcie_wait_phy_link_up port 0 timeout

  469. [    1.250000] pcie_rc_initialize port 0 link up failed!!!!!

  471. [    1.260000] Lantiq PCIe Root Complex Port 0 Init Done

  473. [    1.260000] PCI host bridge /ssx3@18000000/pcie@400000 ranges:

  475. [    1.270000]  MEM 0x00000000b4000000..0x00000000b6ffffff

  477. [    1.270000]   IO 0x00000000b7800000..0x00000000b78fffff

  479. [    1.880000] pcie_wait_phy_link_up port 1 timeout

  481. [    1.880000] pcie_rc_initialize port 1 link up failed!!!!!

  483. [    1.890000] Lantiq PCIe Root Complex Port 1 Init Done

  485. [    1.890000] PCI host bridge /ssx3@18000000/pcie@E00000 ranges:

  487. [    1.900000]  MEM 0x00000000bc000000..0x00000000beffffff

  489. [    1.900000]   IO 0x00000000bf800000..0x00000000bf8fffff

  491. [    2.510000] pcie_wait_phy_link_up port 2 timeout

  493. [    2.510000] pcie_rc_initialize port 2 link up failed!!!!!

  495. [    2.520000] Lantiq PCIe Root Complex Port 2 Init Done

  497. [    2.540000] bio: create slab <bio-0> at 0

  499. [    2.550000] vgaarb: loaded

  501. [    2.550000] SCSI subsystem initialized

  503. [    2.550000] Register xway nand done!

  505. [    2.560000] usbcore: registered new interface driver usbfs

  507. [    2.560000] usbcore: registered new interface driver hub

  509. [    2.570000] usbcore: registered new device driver usb

  511. [    2.570000] i2c-lantiq 16a00000.i2c: pins are not configured from the driver

  513. [    2.580000] i2c-lantiq 16a00000.i2c: setup clocks (in 200000000 kHz, bus 100000 kHz,rmc =20 dec=50 10000000)

  515. [    2.590000] i2c-lantiq 16a00000.i2c: version 1.01

  517. [    2.610000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  519. [    2.630000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  521. [    2.650000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  523. [    2.650000] 1V15VDD: 900 <--> 1200 mV at 1790 mV normal standby

  525. [    2.680000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  527. [    2.700000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  529. [    2.720000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  531. [    2.740000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  533. [    2.760000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  535. [    2.760000] try to register spd_mon driver

  537. [    2.770000] spdmon 16080110.speedm: base address: 0xb6080110       

  539. [    2.770000] spdmon 16080110.speedm: PHY base address: 0x16080110

  541. [    2.780000] device number :253

  543. [    2.780000] spdmon 16080110.speedm: spd_mon driver : init done !!

  545. [    2.790000] spd_mon driver registered

  547. [    2.800000] NET: Registered protocol family 8

  549. [    2.800000] NET: Registered protocol family 20

  551. [    2.810000] cfg80211: Calling CRDA to update world regulatory domain

  553. [    2.810000] Switching to clocksource gptc-timer

  555. [    2.840000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  557. [    2.860000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  559. [    2.880000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  561. [    2.900000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  563. [    2.920000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  565. [    2.940000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready

  567. [    2.940000] ltq_regulator_cpufreq: rcf_debugfs_init is called

  569. [    2.950000] NET: Registered protocol family 2

  571. [    2.950000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)

  573. [    2.960000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)

  575. [    2.970000] TCP: Hash tables configured (established 2048 bind 2048)

  577. [    2.970000] TCP: reno registered

  579. [    2.980000] UDP hash table entries: 256 (order: 1, 8192 bytes)

  581. [    2.980000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)

  583. [    2.990000] NET: Registered protocol family 1

  585. [    2.990000] RPC: Registered named UNIX socket transport module.

  587. [    3.000000] RPC: Registered udp transport module.

  589. [    3.000000] RPC: Registered tcp transport module.

  591. [    3.010000] RPC: Registered tcp NFSv4.1 backchannel transport module.

  593. [    3.020000] phy-xrx500 phy-xrx500.10: requesting lantiq/phy11g_ip_BE.bin

  595. [    3.020000] phy-xrx500 phy-xrx500.10: booting GPHY0 firmware at 27C20000 for GRX500

  597. [    3.130000] phy-xrx500 phy-xrx500.10: booting GPHY1 firmware at 27C20000 for GRX500

  599. [    3.230000] phy-xrx500 phy-xrx500.10: booting GPHY2 firmware at 27C20000 for GRX500

  601. [    3.340000] phy-xrx500 phy-xrx500.10: booting GPHY3 firmware at 27C20000 for GRX500

  603. [    3.440000] phy-xrx500 phy-xrx500.10: booting GPHY4 firmware at 27C20000 for GRX500

  605. [    3.540000] audit: initializing netlink socket (disabled)

  607. [    3.550000] type=2000 audit(3.540:1): initialized

  609. [    3.560000] VFS: Disk quotas dquot_6.5.2

  611. [    3.560000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

  613. [    3.570000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

  615. [    3.570000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled

  617. [    3.580000] msgmni has been set to 370

  619. [    3.590000] io scheduler noop registered

  621. [    3.590000] io scheduler deadline registered (default)

  623. [    3.600000] io scheduler cfq registered

  625. [    3.600000] [vmb_yr_get]:[1362] CPU = 0, yri[i].yr_status = 1, yield_bits = 1 n_yr = 1 yri[i].cpu_id = 0

  627. [    3.610000] [vmb_yr_get]:[1362] CPU = 1, yri[i].yr_status = 1, yield_bits = 2 n_yr = 1 yri[i].cpu_id = 1

  629. [    3.620000] [vmb_yr_get]:[1362] CPU = 2, yri[i].yr_status = 1, yield_bits = 1 n_yr = 1 yri[i].cpu_id = 2

  631. [    3.630000] UMT initialize success!

  633. [    3.630000] HW MCPY driver: Version: 1.1.0, Init Done !!

  635. [    3.640000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled

  637. [    3.650000] lantiq,asc 16600000.serial: pins are not configured from the driver

  639. [    3.660000] 16600000.serial: ttyLTQ0 at MMIO 0x16600000 (irq = 111) is a lantiq,asc

  641. [    3.670000] console [ttyLTQ0] enabled, bootconsole disabled
  642. [    3.670000] console [ttyLTQ0] enabled, bootconsole disabled

  644. [    3.680000] Lantiq MIPSInterAptiv MPS driver, version 1.0.0.0, (c) 2006-2013 Lantiq Deutschland GmbH
  645. [    3.690000] MPS: major Id 251
  646. [    3.690000] Major Id is 250
  647. [    3.700000] ICC driver registered
  648. [    3.700000] sysrst_init: Trying to register System Reset Driver ...
  649. [    3.710000] sysrst_pre_init: Detect InterAptiv CPU ...
  650. [    3.710000] sysrst_init: Lantiq CPE GRX500 System driver version 1.0.0
  651. [    3.720000] sysrst_init: GRX500 System Reset initialized successfully!
  652. [    3.720000] brd: module loaded
  653. [    3.730000] loop: module loaded
  654. [    3.730000] Uniform Multi-Platform E-IDE driver
  655. [    3.730000] ide-gd driver 1.18
  656. [    3.740000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
  657. [    3.750000] Scanning device for bad blocks
  658. [    3.820000] Bad eraseblock 515 at 0x000004060000
  659. [    3.880000] Bad eraseblock 1023 at 0x000007fe0000
  660. [    3.890000] 10 cmdlinepart partitions found on MTD device 17c00000.nand-parts
  661. [    3.890000] Creating 10 MTD partitions on "17c00000.nand-parts":
  662. [    3.900000] 0x000000000000-0x000000100000 : "uboot"
  663. [    3.910000] 0x000000100000-0x000000140000 : "ubootconfigA"
  664. [    3.910000] 0x000000140000-0x000000180000 : "ubootconfigB"
  665. [    3.920000] 0x000000180000-0x0000001c0000 : "gphyfirmware"
  666. [    3.920000] 0x0000001c0000-0x0000002c0000 : "calibration"
  667. [    3.930000] 0x0000002c0000-0x0000012c0000 : "bootcore"
  668. [    3.930000] 0x0000012c0000-0x000001300000 : "pro_info"
  669. [    3.940000] 0x000001300000-0x000001340000 : "dev_info"
  670. [    3.940000] 0x000001340000-0x000007f40000 : "system_sw"
  671. [    3.950000] 0x000007f40000-0x000008000000 : "res"
  672. [    3.950000] Gluebi: Found kernel commandline option 'rootfsname=rootfsB'
  673. [    3.960000] spi-lantiq-ssc 16800000.spi: master is unqueued, this is deprecated
  674. [    3.970000] Lantiq SoC SPI controller rev 9 (TXFS 32, RXFS 32, DMA 1)
  675. [    3.970000] [ltq_ssc] { ifx_ssc_init : 3802 }[ifx_ssc_init] force ifx_ssc_cs_low to PORT 1

  677. [    3.980000] [ltq_ssc] { ifx_ssc_init : 3803 }[ifx_ssc_init] force ifx_ssc_cs_high to PORT 1

  679. [    3.990000] [ltq_ssc] { ifx_ssc_init : 3807 }ifx_ssc_init ifx_ssc_init_count 1

  681. [    4.000000] [ltq_ssc] { ifx_ssc_init : 3930 }port name ltq_ssc1
  682. [    4.000000] [ltq_ssc] { ifx_ssc_init : 4026 }Lantiq SoC SSC controller rev 9 (TXFS 32, RXFS 32, DMA 1)
  683. [    4.010000] [ltq_ssc] { ifx_sscAllocConnection : 3511 }ifx_sscAllocConnection ssc driver must be loaded first!
  684. [    4.020000] ifx_spi_flash_init: failed to register sflash
  685. [    4.030000] IMQ driver loaded successfully. (numdevs = 3, numqueues = 1)
  686. [    4.040000]         Hooking IMQ after NAT on PREROUTING.
  687. [    4.040000]         Hooking IMQ after NAT on POSTROUTING.
  688. [    4.050000] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
  689. [    4.050000] Lantiq VRX318 Version 3.0.0
  690. [    4.060000] LTQ ETH SWITCH API, Version 3.0.2.
  691. [    4.060000] SWAPI: Registered char device [switch_api] with major no [81]
  692. [    4.070000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1717 (pnum:7)
  693. [    4.080000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1784 (gswdev->gipver:48)
  694. [    4.090000] LTQ ETH SWITCH API, Version 3.0.2.
  695. [    4.090000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1717 (pnum:2)
  696. [    4.100000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1784 (gswdev->gipver:48)
  697. [    4.110000] gphy_driver_init: fw_mode:11G-FW, no of phys:5, mode:0
  698. [    4.120000] [datapath_loopeth_dev] { dp_loop_eth_dev_init : 1686 }Loading loop_net_dev driver ......
  699. [    4.130000] [datapath_loopeth_dev] { dp_loop_eth_dev_init : 1692 }dp_loop_eth_dev_init Succeeded!
  700. [    4.140000] [datapath_coc] { dp_coc_new_stat_req : 786 }COC is not initialized yet in DP
  701. [    4.150000] dp init done
  702. [    4.150000] PMAC_EG_CFG_SET for GSW-L
  703. [    4.150000] PMAC_IG_CFG_SET for GSW-L
  704. [    4.160000] PMAC_EG_CFG_SET for GSW-R
  705. [    4.160000] PMAC_IG_CFG_SET for GSW-R
  706. [    4.170000]
  707. [    4.170000]          GSW PMAC Init Done!!!
  708. [    4.170000] registering one of MII bus
  709. [    4.170000] libphy: lantiq,xrx500-mdio: probed
  710. [    4.190000] registering PAE MII bus
  711. [    4.190000] libphy: lantiq,xrx500-mdio-pae: probed
  712. [    4.200000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  713. [    4.210000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  714. [    4.210000] xrx500_of_iface: rx csum offload is enabled !
  715. [    4.220000] trying to connect: eth0_1 to device: 0:02 with irq: 120
  716. [    4.260000] eth0_1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:02, irq=120)
  717. [    4.280000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  718. [    4.290000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  719. [    4.290000] xrx500_of_iface: rx csum offload is enabled !
  720. [    4.300000] trying to connect: eth0_2 to device: 0:03 with irq: 121
  721. [    4.340000] eth0_2: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:03, irq=121)
  722. [    4.360000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  723. [    4.370000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  724. [    4.370000] xrx500_of_iface: rx csum offload is enabled !
  725. [    4.380000] trying to connect: eth0_3 to device: 0:04 with irq: 134
  726. [    4.430000] eth0_3: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:04, irq=134)
  727. [    4.440000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  728. [    4.450000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  729. [    4.450000] xrx500_of_iface: rx csum offload is enabled !
  730. [    4.460000] trying to connect: eth0_4 to device: 0:05 with irq: 135
  731. [    4.510000] eth0_4: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:05, irq=135)
  732. [    4.530000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  733. [    4.530000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  734. [    4.540000] xrx500_of_iface: rx csum offload is enabled !
  735. [    4.540000] trying to connect: eth1 to device: 1:01 with irq: 119
  736. [    4.590000] eth1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=1:01, irq=119)
  737. [    4.610000] register mc group pass: 0, grp name: eth_mcgrp, grp id:6
  738. [    4.610000] Lantiq ethernet driver for XRX500 !
  739. [    4.620000] lro_sram_membase_res0 from DT: a2013000
  740. [    4.620000] ltq_toe_membase: e2000000 and lro_sram_membase_res0: e2013000
  741. [    4.630000] TOE Init Done !!
  742. [    4.630000] PPP generic driver version 2.4.2
  743. [    4.630000] PPP BSD Compression module registered
  744. [    4.640000] PPP Deflate Compression module registered
  745. [    4.640000] PPP MPPE Compression module registered
  746. [    4.650000] NET: Registered protocol family 24
  747. [    4.650000] ltq-dwc3-core 1a300000.usb: no usb3 phy configured
  748. [    4.660000] platform 1a300000.usb: Driver ltq-dwc3-core requests probe deferral
  749. [    4.670000] ltq-dwc3-core 1a500000.usb: no usb3 phy configured
  750. [    4.670000] platform 1a500000.usb: Driver ltq-dwc3-core requests probe deferral
  751. [    4.680000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  752. [    4.690000] ehci-pci: EHCI PCI platform driver
  753. [    4.690000] uhci_hcd: USB Universal Host Controller Interface driver
  754. [    4.700000] usbcore: registered new interface driver usb-storage
  755. [    4.700000] usbcore: registered new interface driver ums-alauda
  756. [    4.710000] usbcore: registered new interface driver ums-datafab
  757. [    4.720000] usbcore: registered new interface driver ums-freecom
  758. [    4.720000] usbcore: registered new interface driver ums-jumpshot
  759. [    4.730000] usbcore: registered new interface driver ums-sddr09
  760. [    4.730000] usbcore: registered new interface driver ums-sddr55
  761. [    4.740000] usbcore: registered new interface driver ums-usbat
  762. [    4.750000] mousedev: PS/2 mouse device common for all mice
  763. [    4.750000] i2c-lantiq 16a00000.i2c: Register I2CCOCDRV to CPUFREQ.
  764. [    4.780000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  765. [    4.800000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  766. [    4.800000] ina2xx 0-0040: power monitor: ina219, railname:  PWR_12V, Rshunt: 10000 uOhm
  767. [    4.810000] [gptu] { setrate : 154 }cpu_clk 200000000

  769. [    4.810000] [gptu] { setrate : 158 }reload_counter_value 1

  771. [    4.820000] gpio-sso-xrx500 16d00000.sso: pins are not configured from the driver
  772. [    4.830000] gpio-sso-xrx500 16d00000.sso: Init done
  773. [    4.830000] Device IRQ: 97 line: 100
  774. [    4.830000] GlobalControl97_Capabilities_Get
  775. [    4.840000] EIP202: PEs=1 rings=4 64-bit=No, fill level extension=No
  776. [    4.840000] CF size=4 RF size=3 DMA len = 10 Align=0 HDW=0 HostIfc=3
  777. [    4.850000] EIP96 options:
  778. [    4.850000] AES: Yes with CFB/OFB: Yes Fast: Yes
  779. [    4.850000] DES: Yes with CFB/OFB: Yes Fast: No
  780. [    4.850000] ARCFOUR level: 3
  781. [    4.850000] MD5: Yes SHA1: Yes Fast: Yes SHA256: Yes SHA512: Yes
  782. [    4.850000] (X)CBC-MAC: Yes Fast: Yes All key sizes: No GHASH Yes
  783. [    4.880000] EIP97 options: PEs=1, In Dbuf size=6 In Tbuf size=5, Out Dbuf size=6, Out Tbuf size=4,
  784. [    4.880000] Token Generator: No, Transform Record Cache: No
  785. [    4.890000] EIP206 options: PE type=0 InClassifier=0 OutClassifier=0 MAC chans=0
  786. [    4.890000] InDBuf=0kB InTBuf=0kB OutDBuf=0kB OutTBuf=0kB
  787. [    4.910000] Global EIP-97 capabilities: EIP-97 v1.2p1  with EIP-202 v1.3p0 and EIP-96 v2.2p3, #PE=01 #rings=04
  788. [    4.920000] Global Status of the EIP-97
  789. [    4.920000] Packet Engine 0 Status
  790. [    4.920000] DFE Status: CD FIFO Words: 0, CDR ID: 15, DMA size: 0
  791. [    4.920000] AtDMA busy: false, DataDMA busy: false, DMA err: false
  792. [    4.930000] DSE Status: RD FIFO Words: 0, RDR ID: 15, DMA size: 0
  793. [    4.930000] Data flush  busy: false, DataDMA busy: false, DMA err: false
  794. [    4.950000] Token Status: Active: 0, loc available: true
  795. [    4.950000] res available: false, read active: false, ccache active: false
  796. [    4.950000] cntx fetch: false, res cntx: false
  797. [    4.950000] processing held: true, busy: false
  798. [    4.970000] Context Status: Err mask: 0000, Available: 0
  799. [    4.970000] Active cntx: false, next cntx: false, result cntx: false Err recov: false
  800. [    4.980000] Interrupt Status: input DMA err: false, output DMA err false
  801. [    4.980000] pkt proc err: false, pkt timeout: false, f a t a l err: false, PE int out: false
  802. [    4.980000] inp DMA enable: false, outp DMA enable false, pkt proc enable: false
  803. [    4.980000] pkt timeout enable: false, f a t a l enable: false,PE int out enable: false
  804. [    5.010000] Output Transfer Status: availabe: 71, min: 8, max: 64, size mask: 252
  805. [    5.020000] PRNG Status: busy: true, res ready: false
  806. [    5.020000] Adapter_Lock_Alloc: Lock = spinlock
  807. [    5.030000] Adapter_Lock_Alloc: Lock = spinlock
  808. [    5.030000] Adapter_PECDev_Init: CDR fetch size 0x8, thresh 0x6, HDW=0, CFsize=4
  809. [    5.040000] Adapter_PECDev_Init: RDR fetch size 0x8, thresh 0x2, RFsize=3
  810. [    5.050000] Status of CDR/RDR interface 0
  811. [    5.050000] CDR Status: DMA err: false, err: false: ovf/under err: false
  812. [    5.050000] Threshold int: false, timeout int: false, FIFO count: 16
  813. [    5.070000] RDR Status: DMA err: false, err: false: ovf/under err: false
  814. [    5.070000] Buf ovf: false, Descriptor ovf false
  815. [    5.070000] Threshold int: false, timeout int: false, FIFO count: 8
  816. [    5.080000] Adapter_Lock_Alloc: Lock = spinlock
  817. [    5.090000] Adapter_Lock_Alloc: Lock = spinlock
  818. [    5.090000] Adapter_PECDev_Init: CDR fetch size 0x8, thresh 0x6, HDW=0, CFsize=4
  819. [    5.100000] Adapter_PECDev_Init: RDR fetch size 0x8, thresh 0x2, RFsize=3
  820. [    5.110000] Status of CDR/RDR interface 1
  821. [    5.110000] CDR Status: DMA err: false, err: false: ovf/under err: false
  822. [    5.110000] Threshold int: false, timeout int: false, FIFO count: 16
  823. [    5.120000] RDR Status: DMA err: false, err: false: ovf/under err: false
  824. [    5.120000] Buf ovf: false, Descriptor ovf false
  825. [    5.120000] Threshold int: false, timeout int: false, FIFO count: 8
  826. [    5.140000] LTQ Crypto Hardware Initialized ..
  827. [    5.150000] LTQ crypto driver version: 1.2.24
  828. [    5.150000] usbcore: registered new interface driver usbhid
  829. [    5.160000] usbhid: USB HID core driver
  830. [    5.160000] u32 classifier
  831. [    5.160000]     input device check on
  832. [    5.170000]     Actions configured
  833. [    5.170000] nf_conntrack version 0.5.0 (2964 buckets, 11856 max)
  834. [    5.180000] nf_conntrack_rtsp v0.6.21 loading
  835. [    5.180000] xt_time: kernel timezone is -0000
  836. [    5.180000] ipip: IPv4 over IPv4 tunneling driver
  837. [    5.190000] nf_nat_rtsp v0.6.21 loading
  838. [    5.190000] ip_tables: (C) 2000-2006 Netfilter Core Team
  839. [    5.200000] TCP: cubic registered
  840. [    5.200000] Initializing XFRM netlink socket
  841. [    5.210000] NET: Registered protocol family 10
  842. [    5.210000] NET: Registered protocol family 17
  843. [    5.220000] NET: Registered protocol family 15
  844. [    5.220000] Bridge firewalling registered
  845. [    5.220000] Ebtables v2.0 registered
  846. [    5.230000] lec:lane_module_init: lec.c: initialized
  847. [    5.230000] mpoa:atm_mpoa_init: mpc.c: initialized
  848. [    5.240000] KOAM is loaded successfully.
  849. [    5.240000] l2tp_core: L2TP core driver, V2.0
  850. [    5.250000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  851. [    5.250000] l2tp_netlink: L2TP netlink interface
  852. [    5.250000] 8021q: 802.1Q VLAN Support v1.8
  853. [    5.260000] regulator-dummy: disabling
  854. [    6.430000] UBI: attaching mtd8 to ubi0
  855. [    8.450000] UBI: scanning is finished
  856. [    8.480000] UBI: attached mtd8 (name "system_sw", size 108 MiB) to ubi0
  857. [    8.490000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  858. [    8.500000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
  859. [    8.500000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
  860. [    8.510000] UBI: good PEBs: 863, bad PEBs: 1, corrupted PEBs: 0
  861. [    8.520000] UBI: user volume: 6, internal volumes: 1, max. volumes count: 128
  862. [    8.520000] UBI: max/mean erase counter: 74/11, WL threshold: 4096, image sequence number: 1777296557
  863. [    8.530000] UBI: available PEBs: 450, total reserved PEBs: 413, PEBs reserved for bad PEB handling: 19
  864. [    8.540000] UBI: background thread "ubi_bgt0d" started, PID 590
  865. [    8.550000] drivers/rtc/hctosys.c: unable to open rtc dev[    8.570000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
  866. [    8.570000] Please append a correct "root=" boot option; here are the available partitions:
  867. [    8.580000] 1f00            1024 mtdblock0  (driver?)
  868. [    8.590000] 1f01             256 mtdblock1  (driver?)
  869. [    8.590000] 1f02             256 mtdblock2  (driver?)
  870. [    8.600000] 1f03             256 mtdblock3  (driver?)
  871. [    8.600000] 1f04            1024 mtdblock4  (driver?)
  872. [    8.610000] 1f05           16384 mtdblock5  (driver?)
  873. [    8.610000] 1f06             256 mtdblock6  (driver?)
  874. [    8.620000] 1f07             256 mtdblock7  (driver?)
  875. [    8.620000] 1f08          110592 mtdblock8  (driver?)
  876. [    8.630000] 1f09             768 mtdblock9  (driver?)
  877. [    8.630000] 1f0a            2944 mtdblock10  (driver?)
  878. [    8.640000] 1f0b           16616 mtdblock11  (driver?)
  879. [    8.640000] 1f0c            2976 mtdblock12  (driver?)
  880. [    8.650000] 1f0d            2604 mtdblock13  (driver?)
  881. [    8.650000] 1f0e            2604 mtdblock14  (driver?)
  882. [    8.660000] 1f0f           20584 mtdblock15  (driver?)
  883. [    8.660000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
  884. [    8.660000] Rebooting in 1 seconds..
  885. ROM VER: 2.1.0
  886. CFG 0a
  887. B
  888. .
  889. .
复制代码

k3 ttl没反应, k3c刷ttl救砖, k3c变砖 修复

相关帖子

请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

呆***
| 显示全部楼层
怎么看的三星内存？还有路由器刷完重置过吗？
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

xy***
| 显示全部楼层
目前还没有修复办法，报修吧。通常是给你换一个。
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

viru***
 楼主| | 显示全部楼层
呆头铭 发表于 2017-10-21 22:40
怎么看的三星内存？还有路由器刷完重置过吗？

TTL日志可以看出来是三星的NAND。第15行。
一开始官改不正常的时候，长按重置过，无效。
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

viru***
 楼主| | 显示全部楼层
xytb 发表于 2017-10-21 22:43
目前还没有修复办法，报修吧。通常是给你换一个。

别提了，转转上收的。斐讯要我提供购买渠道，死活联系不上卖家。
后来索性就拆了上TTL线看看日志。
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

xy***
| 显示全部楼层
virus1999 发表于 2017-10-21 22:50
别提了，转转上收的。斐讯要我提供购买渠道，死活联系不上卖家。
后来索性就拆了上TTL线看看日志。

在救砖方法没出来前先吃灰吧。
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

来自手机 | 显示全部楼层
k3c不适宜刷机，安心用官方吧
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

pal***
| 显示全部楼层
本帖最后由 paldier 于 2017-10-21 23:06 编辑
  1. https://pan.baidu.com/s/1kUVXm0B
  2. 下载93或者113
  3. 捅住菊花插电大概15秒后松手，电脑设置192.168.2.100，浏览器打开192.168.2.1，上传93或者113，也可以先设ip用ping看能ping通后松手
  4. 我记得这样会同时刷bankA和bankB，应该能恢复system_sw,如果不行又不想换mxic那么就只能等等了，后面的方法需要在uboot下手动擦除nand，没有稳定的方法前不推荐试
  5. 如果你刷过官改，这个时候你就靠拼脸了，如果刚好官改没有修改重要属性你就可以正常进系统了

  7. 如果能启动就算不正常也好办
  8. 默认账号admin无密码
  9. opkg install http://k3c.paldier.tk/packages/dropbear_2015.67-1_lantiq.ipk
  10. /etc/init.d/dropbear enable
  11. /etc/init.d/dropbear start
  12. passwd admin
  13. 输两次你的密码
  14. 然后用mtd write刷回备份就好了
复制代码
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

zcy***
| 显示全部楼层
貌似只能用官改  别的不要想了
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

19***
| 显示全部楼层
好明显是出现坏快，擦除下，uboot应该有擦除命令，键入help 查看吧
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

viru***
 楼主| | 显示全部楼层
paldier 发表于 2017-10-21 23:01

谢谢paldier回复，明天试试，今天整不动了……
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

602***
| 显示全部楼层
又是一个在uboot下作死的
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

pal***
| 显示全部楼层
6022652 发表于 2017-10-21 23:34
又是一个在uboot下作死的

什么叫在uboot下作死，uboot本来就是干这个的，你觉得牙膏厂连本职都干不好吗
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

ai5***
| 显示全部楼层
virus1999 发表于 2017-10-21 22:50
别提了，转转上收的。斐讯要我提供购买渠道，死活联系不上卖家。
后来索性就拆了上TTL线看看日志。

你就说网上买的。目前找不到商家了。老板已经翻车跑路了。然后寄过去给你换新
请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

viru***
 楼主| | 显示全部楼层
本帖最后由 virus1999 于 2017-10-22 16:16 编辑
paldier 发表于 2017-10-21 23:01

刷了你提供的固件，无效。放起来吃灰了。
附上TTL日志，看443行开始的日志，还有536行，提示是：Unknown image type!!
  1. [15:19:18][20171022_15:19:18]
  2. [15:21:42]ROM VER: 2.1.0
  3. [15:21:42]CFG 0a
  4. [15:21:42]B
  5. [15:21:42].
  6. [15:21:42].
  7. [15:21:44]
  8. [15:21:44]
  9. [15:21:44]U-Boot 2010.06-00044-gb399a23-LANTIQ-v-2.3.136 (Jul 24 2017 - 10:45:54)
  10. [15:21:44]
  11. [15:21:44]interAptiv
  12. [15:21:44]cps cpu/ddr run in 800/666 Mhz
  13. [15:21:44]DRAM:  224 MiB
  14. [15:21:44]NAND:  Could not find valid JEDEC parameter page; aborting
  15. [15:21:44]NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
  16. [15:21:44]128 MiB
  17. [15:21:44]Bad block table found at page 65408, version 0x01
  18. [15:21:44]Bad block table found at page 65344, version 0x01
  19. [15:21:44]nand_read_bbt: Bad block at 0x000004060000
  20. [15:21:44]nand_read_bbt: Bad block at 0x000007fe0000
  21. [15:21:44]In:    serial
  22. [15:21:44]Out:   serial
  23. [15:21:44]Err:   serial
  24. [15:21:44]Net:   multi type
  25. [15:21:47]Internal phy firmware version: 0x853c
  26. [15:21:47]GRX500 Switch
  27. [15:21:47]
  28. [15:21:47]Type "run flash_nfs" to mount root filesystem over NFS
  29. [15:21:47]
  30. [15:21:47]
  31. [15:21:47]Press press hardware button for more than 4 seconds to run web failsafe mode
  32. [15:21:47]
  33. [15:21:57]10 second(s)
  34. [15:21:57]
  35. [15:21:57]hardware button was pressed for 10 seconds
  36. [15:21:57]HTTP server is starting for firmware update...
  37. [15:21:57]
  38. [15:21:57]
  39. [15:21:57] NetLoopHttpd,call eth_halt !
  40. [15:21:57]HTTP server is starting at IP: 192.168.2.1
  41. [15:21:57]HTTP server is ready!
  42. [15:21:57]
  43. [15:22:07]Request for: /
  44. [15:22:07]Request for: /style.css
  45. [15:22:14]Found boundary value: "-----------------------------273762184026984"
  46. [15:22:14]Data will be downloaded at 0x80800000 in RAM
  47. [15:22:14]Upgrade type: sopimg
  48. [15:22:14]Upload file size: 20214920 bytes
  49. [15:22:14]Loading: #######################################
  50. [15:22:14]         #######################################
  51. [15:22:14]         #######################################
  52. [15:22:14]         #######################################
  53. [15:22:14]         #######################################
  54. [15:22:14]         #######################################
  55. [15:22:14]         #######################################
  56. [15:22:14]         #######################################
  57. [15:22:14]         #######################################
  58. [15:22:14]         #######################################
  59. [15:22:14]         #######################################
  60. [15:22:14]         #######################################
  61. [15:22:14]         #######################################
  62. [15:22:14]         #######################################
  63. [15:22:14]         #######################################
  64. [15:22:14]         #######################################
  65. [15:22:14]         #######################################
  66. [15:22:14]         #######################################
  67. [15:22:14]         #######################################
  68. [15:22:14]         #######################################
  69. [15:22:14]         #######################################
  70. [15:22:14]         #######################################
  71. [15:22:14]         #######################################
  72. [15:22:14]         #######################################
  73. [15:22:14]         #######################################
  74. [15:22:14]         #######################################
  75. [15:22:14]         #######################################
  76. [15:22:14]         #######################################
  77. [15:22:14]         #######################################
  78. [15:22:14]         #######################################
  79. [15:22:14]         #######################################
  80. [15:22:14]         #######################################
  81. [15:22:14]         #######################################
  82. [15:22:14]         #######################################
  83. [15:22:14]         #######################################
  84. [15:22:14]         #######################################
  85. [15:22:14]         #######################################
  86. [15:22:14]         #######################################
  87. [15:22:14]         #######################################
  88. [15:22:14]         #######################################
  89. [15:22:14]         #######################################
  90. [15:22:14]         #######################################
  91. [15:22:14]         #######################################
  92. [15:22:14]         #######################################
  93. [15:22:14]         #######################################
  94. [15:22:14]         #######################################
  95. [15:22:14]         #######################################
  96. [15:22:14]         #######################################
  97. [15:22:14]         #######################################
  98. [15:22:14]         #######################################
  99. [15:22:14]         #######################################
  100. [15:22:14]         #######################################
  101. [15:22:14]         #######################################
  102. [15:22:14]         #######################################
  103. [15:22:14]         #######################################
  104. [15:22:14]         #######################################
  105. [15:22:14]         #######################################
  106. [15:22:14]         #######################################
  107. [15:22:14]         #######################################
  108. [15:22:14]         #######################################
  109. [15:22:14]         #######################################
  110. [15:22:14]         #######################################
  111. [15:22:14]         #######################################
  112. [15:22:14]         #######################################
  113. [15:22:14]         #######################################
  114. [15:22:14]         #######################################
  115. [15:22:14]         #######################################
  116. [15:22:14]         #######################################
  117. [15:22:14]         #######################################
  118. [15:22:14]         #######################################
  119. [15:22:14]         #######################################
  120. [15:22:14]         #######################################
  121. [15:22:14]         #######################################
  122. [15:22:14]         #######################################
  123. [15:22:14]         #######################################
  124. [15:22:14]         #######################################
  125. [15:22:14]         #######################################
  126. [15:22:14]         #######################################
  127. [15:22:14]         #######################################
  128. [15:22:14]         #######################################
  129. [15:22:14]         #######################################
  130. [15:22:14]         #######################################
  131. [15:22:14]         #######################################
  132. [15:22:14]         #######################################
  133. [15:22:14]         #######################################
  134. [15:22:14]         #######################################
  135. [15:22:14]         #######################################
  136. [15:22:14]         #######################################
  137. [15:22:14]         #######################################
  138. [15:22:14]         #######################################
  139. [15:22:14]         #######################################
  140. [15:22:14]         #######################################
  141. [15:22:14]         #######################################
  142. [15:22:14]         #######################################
  143. [15:22:14]         #######################################
  144. [15:22:14]         #######################################
  145. [15:22:14]         #######################################
  146. [15:22:14]         #######################################
  147. [15:22:14]         #######################################
  148. [15:22:14]         #######################################
  149. [15:22:14]         #######################################
  150. [15:22:14]         #######################################
  151. [15:22:14]         #######################################
  152. [15:22:14]         #######################################
  153. [15:22:14]         #######################################
  154. [15:22:14]         #######################################
  155. [15:22:14]         #######################################
  156. [15:22:14]         #######################################
  157. [15:22:14]         #######################################
  158. [15:22:14]         #######################################
  159. [15:22:14]         #######################################
  160. [15:22:14]         #######################################
  161. [15:22:14]         #######################################
  162. [15:22:14]         #######################################
  163. [15:22:14]         #######################################
  164. [15:22:14]         #######################################
  165. [15:22:14]         #######################################
  166. [15:22:14]         #######################################
  167. [15:22:14]         #######################################
  168. [15:22:14]         #######################################
  169. [15:22:14]         #######################################
  170. [15:22:14]         #######################################
  171. [15:22:14]         #######################################
  172. [15:22:14]         #######################################
  173. [15:22:14]         #######################################
  174. [15:22:14]         #######################################
  175. [15:22:14]         #######################################
  176. [15:22:14]         #######################################
  177. [15:22:14]         #######################################
  178. [15:22:14]         #######################################
  179. [15:22:14]         #######################################
  180. [15:22:14]         #######################################
  181. [15:22:14]         #######################################
  182. [15:22:14]         #######################################
  183. [15:22:14]         #######################################
  184. [15:22:14]         #######################################
  185. [15:22:14]         #######################################
  186. [15:22:14]         #######################################
  187. [15:22:14]         #######################################
  188. [15:22:14]         #######################################
  189. [15:22:14]         #######################################
  190. [15:22:14]         #######################################
  191. [15:22:15]         #######################################
  192. [15:22:15]         #######################################
  193. [15:22:15]         #######################################
  194. [15:22:15]         #######################################
  195. [15:22:15]         #######################################
  196. [15:22:15]         #######################################
  197. [15:22:15]         #######################################
  198. [15:22:15]         #######################################
  199. [15:22:15]         #######################################
  200. [15:22:15]         #######################################
  201. [15:22:15]         #######################################
  202. [15:22:15]         #######################################
  203. [15:22:15]         #######################################
  204. [15:22:15]         #######################################
  205. [15:22:15]         #######################################
  206. [15:22:15]         #######################################
  207. [15:22:15]         #######################################
  208. [15:22:15]         #######################################
  209. [15:22:15]         #######################################
  210. [15:22:15]         #######################################
  211. [15:22:15]         #######################################
  212. [15:22:15]         #######################################
  213. [15:22:15]         #######################################
  214. [15:22:15]         #######################################
  215. [15:22:15]         #######################################
  216. [15:22:15]         #######################################
  217. [15:22:15]         #######################################
  218. [15:22:15]         #######################################
  219. [15:22:15]         #######################################
  220. [15:22:15]         #######################################
  221. [15:22:15]         #######################################
  222. [15:22:15]         #######################################
  223. [15:22:15]         #######################################
  224. [15:22:15]         #######################################
  225. [15:22:15]         #######################################
  226. [15:22:15]         #######################################
  227. [15:22:15]         #######################################
  228. [15:22:15]         #######################################
  229. [15:22:15]         #######################################
  230. [15:22:15]         #######################################
  231. [15:22:15]         #######################################
  232. [15:22:15]         #######################################
  233. [15:22:15]         #######################################
  234. [15:22:15]         #######################################
  235. [15:22:15]         #######################################
  236. [15:22:15]         #######################################
  237. [15:22:15]         #######################################
  238. [15:22:15]         #######################################
  239. [15:22:15]         #######################################
  240. [15:22:15]         #######################################
  241. [15:22:15]         #######################################
  242. [15:22:15]         #######################################
  243. [15:22:15]         #######################################
  244. [15:22:15]         #######################################
  245. [15:22:15]         #######################################
  246. [15:22:15]         #######################################
  247. [15:22:15]         #######################################
  248. [15:22:15]         #######################################
  249. [15:22:15]         #######################################
  250. [15:22:15]         #######################################
  251. [15:22:15]         #######################################
  252. [15:22:15]         #######################################
  253. [15:22:15]         #######################################
  254. [15:22:15]         #######################################
  255. [15:22:15]         #######################################
  256. [15:22:15]         #######################################
  257. [15:22:15]         #######################################
  258. [15:22:15]         #######################################
  259. [15:22:15]         #######################################
  260. [15:22:15]         #######################################
  261. [15:22:15]         #######################################
  262. [15:22:15]         #######################################
  263. [15:22:15]         #######################################
  264. [15:22:15]         #######################################
  265. [15:22:15]         #######################################
  266. [15:22:15]         #######################################
  267. [15:22:15]         #######################################
  268. [15:22:15]         #######################################
  269. [15:22:15]         #######################################
  270. [15:22:15]         #######################################
  271. [15:22:15]         #######################################
  272. [15:22:15]         #######################################
  273. [15:22:15]         #######################################
  274. [15:22:15]         #######################################
  275. [15:22:15]         #######################################
  276. [15:22:15]         #######################################
  277. [15:22:15]         #######################################
  278. [15:22:15]         #######################################
  279. [15:22:15]         #######################################
  280. [15:22:15]         #######################################
  281. [15:22:15]         #######################################
  282. [15:22:15]         #######################################
  283. [15:22:15]         #######################################
  284. [15:22:15]         #######################################
  285. [15:22:15]         #######################################
  286. [15:22:15]         #######################################
  287. [15:22:15]         #######################################
  288. [15:22:15]         #######################################
  289. [15:22:15]         #######################################
  290. [15:22:15]         #######################################
  291. [15:22:15]         #######################################
  292. [15:22:15]         #######################################
  293. [15:22:15]         #######################################
  294. [15:22:15]         #######################################
  295. [15:22:15]         #######################################
  296. [15:22:15]         #######################################
  297. [15:22:15]         #######################################
  298. [15:22:15]         #######################################
  299. [15:22:15]         #######################################
  300. [15:22:15]         #######################################
  301. [15:22:15]         #######################################
  302. [15:22:15]         #######################################
  303. [15:22:15]         #######################################
  304. [15:22:15]         #######################################
  305. [15:22:15]         #######################################
  306. [15:22:15]         #######################################
  307. [15:22:15]         #######################################
  308. [15:22:15]         #######################################
  309. [15:22:15]         #######################################
  310. [15:22:15]         #######################################
  311. [15:22:15]         #######################################
  312. [15:22:15]         #######################################
  313. [15:22:15]         #######################################
  314. [15:22:15]         #######################################
  315. [15:22:15]         #######################################
  316. [15:22:15]         #######################################
  317. [15:22:15]         #######################################
  318. [15:22:15]         #######################################
  319. [15:22:15]         #######################################
  320. [15:22:15]         #######################################
  321. [15:22:15]         #######################################
  322. [15:22:15]         #######################################
  323. [15:22:15]         #######################################
  324. [15:22:15]         #######################################
  325. [15:22:15]         #######################################
  326. [15:22:15]         #######################################
  327. [15:22:15]         #######################################
  328. [15:22:15]         #######################################
  329. [15:22:15]         #######################################
  330. [15:22:15]         #######################################
  331. [15:22:15]         #######################################
  332. [15:22:15]         #######################################
  333. [15:22:15]         #######################################
  334. [15:22:15]         #######################################
  335. [15:22:15]         #######################################
  336. [15:22:15]         #######################################
  337. [15:22:15]         #######################################
  338. [15:22:15]         #######################################
  339. [15:22:15]         #######################################
  340. [15:22:15]         #######################################
  341. [15:22:15]         #######################################
  342. [15:22:15]         #######################################
  343. [15:22:15]         #######################################
  344. [15:22:15]         #######################################
  345. [15:22:15]         #######################################
  346. [15:22:15]         #######################################
  347. [15:22:15]         #######################################
  348. [15:22:15]         #######################################
  349. [15:22:15]         #######################################
  350. [15:22:15]         #######################################
  351. [15:22:15]         #######################################
  352. [15:22:15]         #######################################
  353. [15:22:15]         #######################################
  354. [15:22:15]         #######################################
  355. [15:22:15]         #######################################
  356. [15:22:15]         #######################################
  357. [15:22:15]         #######################################
  358. [15:22:15]         #######################################
  359. [15:22:15]         #######################################
  360. [15:22:15]         #######################################
  361. [15:22:15]         #######################################
  362. [15:22:15]         #######################################
  363. [15:22:15]         #######################################
  364. [15:22:15]         #######################################
  365. [15:22:15]         #######################################
  366. [15:22:15]         #######################################
  367. [15:22:15]         #######################################
  368. [15:22:15]         #######################################
  369. [15:22:15]         #######################################
  370. [15:22:15]         #######################################
  371. [15:22:15]         #######################################
  372. [15:22:15]         #######################################
  373. [15:22:15]         #######################################
  374. [15:22:15]         #######################################
  375. [15:22:15]         #######################################
  376. [15:22:15]         #######################################
  377. [15:22:15]         #######################################
  378. [15:22:15]         #######################################
  379. [15:22:15]         #######################################
  380. [15:22:15]         #######################################
  381. [15:22:15]         #######################################
  382. [15:22:15]         #######################################
  383. [15:22:15]         #######################################
  384. [15:22:15]         #######################################
  385. [15:22:15]         #######################################
  386. [15:22:15]         #######################################
  387. [15:22:15]         #######################################
  388. [15:22:15]         #######################################
  389. [15:22:15]         #######################################
  390. [15:22:15]         #######################################
  391. [15:22:15]         #######################################
  392. [15:22:15]         #######################################
  393. [15:22:15]         #######################################
  394. [15:22:15]         #######################################
  395. [15:22:15]         #######################################
  396. [15:22:16]         #######################################
  397. [15:22:16]         #######################################
  398. [15:22:16]         #######################################
  399. [15:22:16]         #######################################
  400. [15:22:16]         #######################################
  401. [15:22:16]         #######################################
  402. [15:22:16]         #######################################
  403. [15:22:16]         #######################################
  404. [15:22:16]         #######################################
  405. [15:22:16]         #######################################
  406. [15:22:16]         #######################################
  407. [15:22:16]         ###############################
  408. [15:22:16]
  409. [15:22:16]HTTP upload is done! Upgrading...
  410. [15:22:16]Creating 1 MTD partitions on "nand0":
  411. [15:22:16]0x000001340000-0x000007f40000 : "mtd=8"
  412. [15:22:16]UBI: attaching mtd1 to ubi0
  413. [15:22:16]UBI: physical eraseblock size:   131072 bytes (128 KiB)
  414. [15:22:16]UBI: logical eraseblock size:    126976 bytes
  415. [15:22:16]UBI: smallest flash I/O unit:    2048
  416. [15:22:16]UBI: VID header offset:          2048 (aligned 2048)
  417. [15:22:16]UBI: data offset:                4096
  418. [15:22:18]UBI: attached mtd1 to ubi0
  419. [15:22:18]UBI: MTD device name:            "mtd=8"
  420. [15:22:18]UBI: MTD device size:            108 MiB
  421. [15:22:18]UBI: number of good PEBs:        863
  422. [15:22:18]UBI: number of bad PEBs:         1
  423. [15:22:18]UBI: max. allowed volumes:       128
  424. [15:22:18]UBI: wear-leveling threshold:    4096
  425. [15:22:18]UBI: number of internal volumes: 1
  426. [15:22:18]UBI: number of user volumes:     6
  427. [15:22:18]UBI: available PEBs:             461
  428. [15:22:18]UBI: total number of reserved PEBs: 402
  429. [15:22:18]UBI: number of PEBs reserved for bad PEB handling: 8
  430. [15:22:18]UBI: max/mean erase counter: 86/11
  431. [15:22:18]
  432. [15:22:18]
  433. [15:22:18]****************************
  434. [15:22:18]*    IOPIMG UPGRADING    *
  435. [15:22:18]* DO NOT POWER OFF DEVICE! *
  436. [15:22:18]****************************
  437. [15:22:18]
  438. [15:22:18]srcAddr=80800000
  439. [15:22:18]srcLen=20214920
  440. [15:22:18]srcHeader=0x80800000
  441. [15:22:18]curParSize=0x40
  442. [15:22:18]pad=0x0
  443. [15:22:18]Unknown image type!!
  444. [15:22:18]srcHeader=0x80800040
  445. [15:22:18]curParSize=0x40
  446. [15:22:18]pad=0x0
  447. [15:22:18]Unknown image type!!
  448. [15:22:18]srcHeader=0x80800080
  449. [15:22:18]curParSize=0x40
  450. [15:22:18]pad=0x0
  451. [15:22:18]Unknown image type!!
  452. [15:22:18]srcHeader=0x808000c0
  453. [15:22:18]curParSize=0x40
  454. [15:22:18]pad=0x0
  455. [15:22:18]Unknown image type!!
  456. [15:22:18]srcHeader=0x80800100
  457. [15:22:18]curParSize=0x40
  458. [15:22:18]pad=0x0
  459. [15:22:18]Unknown image type!!
  460. [15:22:18]srcHeader=0x80800140
  461. [15:22:18]curParSize=0x40
  462. [15:22:18]pad=0x0
  463. [15:22:18]Unknown image type!!
  464. [15:22:18]srcHeader=0x80800180
  465. [15:22:18]curParSize=0x40
  466. [15:22:18]pad=0x0
  467. [15:22:18]Unknown image type!!
  468. [15:22:18]srcHeader=0x808001c0
  469. [15:22:18]curParSize=0x40
  470. [15:22:18]pad=0x0
  471. [15:22:18]Unknown image type!!
  472. [15:22:18]srcHeader=0x80800200
  473. [15:22:18]curParSize=0x40
  474. [15:22:18]pad=0x0
  475. [15:22:18]Unknown image type!!
  476. [15:22:18]srcHeader=0x80800240
  477. [15:22:18]curParSize=0x40
  478. [15:22:18]pad=0x0
  479. [15:22:18]Unknown image type!!
  480. [15:22:18]srcHeader=0x80800280
  481. [15:22:18]curParSize=0x40
  482. [15:22:18]pad=0x0
  483. [15:22:18]Unknown image type!!
  484. [15:22:18]srcHeader=0x808002c0
  485. [15:22:18]curParSize=0x40
  486. [15:22:18]pad=0x0
  487. [15:22:18]Unknown image type!!
  488. [15:22:18]srcHeader=0x80800300
  489. [15:22:18]curParSize=0x40
  490. [15:22:18]pad=0x0
  491. [15:22:18]Unknown image type!!
  492. [15:22:18]srcHeader=0x80800340
  493. [15:22:18]curParSize=0x40
  494. [15:22:18]pad=0x0
  495. [15:22:18]Unknown image type!!
  496. [15:22:18]srcHeader=0x80800380
  497. [15:22:18]curParSize=0x40
  498. [15:22:18]pad=0x0
  499. [15:22:18]Unknown image type!!
  500. [15:22:18]srcHeader=0x808003c0
  501. [15:22:18]curParSize=0x40
  502. [15:22:18]pad=0x0
  503. [15:22:18]Unknown image type!!
  504. [15:22:18]srcHeader=0x80800400
  505. [15:22:18]curParSize=0x1327088
  506. [15:22:18]pad=0x8
  507. [15:22:18]srcHeader=0x80800448
  508. [15:22:18]curParSize=0x1047040
  509. [15:22:18]pad=0x0
  510. [15:22:18]upgrade now!
  511. [15:22:18]Image contains header with name [LTQCPE RootFS]
  512. [15:22:18]rootfsB volume not found
  513. [15:22:18]Creating dynamic volume rootfsB of size 17068032 and volume id 4
  514. [15:22:18]UBI error: ubi_create_volume: cannot create volume 4, error -17
  515. [15:22:18]rootfsB volume not found
  516. [15:22:18]Erasing redundant Nand...
  517. [15:22:18]
  518. [15:22:18]Writing to redundant Nand... done
  519. [15:22:18]upgrade_img done!!
  520. [15:22:18]srcHeader=0x81847488
  521. [15:22:18]curParSize=0x2e0000
  522. [15:22:18]pad=0x0
  523. [15:22:18]upgrade now!
  524. [15:22:18]Image contains header with name [MIPS LTQCPE Linux-3.10.102]
  525. [15:22:18]Volume kernelB found at valid 3
  526. [15:22:18]remove UBI volume kernelB (id 3)
  527. [15:22:18]Creating dynamic volume kernelB of size 3014656 and volume id 3
  528. [15:22:18]Volume "kernelB" found at volume id 3
  529. [15:22:20]Erasing Nand...
  530. [15:22:20]
  531. [15:22:20]Writing to Nand... done
  532. [15:22:20]upgrade_img done!!
  533. [15:22:20]srcHeader=0x81b27488
  534. [15:22:20]curParSize=0x5e5410c6
  535. [15:22:20]pad=0xa
  536. [15:22:20]Unknown image type!!
  537. [15:22:20]http_upgrade done!
  538. [15:22:21]HTTP ugrade is done! Rebooting...
  539. [15:22:21]
  540. [15:22:21]
  541. [15:22:21]ROM VER: 2.1.0
  542. [15:22:21]CFG 0a
  543. [15:22:21]B
  544. [15:22:21].
  545. [15:22:21].
  546. [15:22:24]
  547. [15:22:24]
  548. [15:22:24]U-Boot 2010.06-00044-gb399a23-LANTIQ-v-2.3.136 (Jul 24 2017 - 10:45:54)
  549. [15:22:24]
  550. [15:22:24]interAptiv
  551. [15:22:24]cps cpu/ddr run in 800/666 Mhz
  552. [15:22:24]DRAM:  224 MiB
  553. [15:22:24]NAND:  Could not find valid JEDEC parameter page; aborting
  554. [15:22:24]NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
  555. [15:22:24]128 MiB
  556. [15:22:24]Bad block table found at page 65408, version 0x01
  557. [15:22:24]Bad block table found at page 65344, version 0x01
  558. [15:22:24]nand_read_bbt: Bad block at 0x000004060000
  559. [15:22:24]nand_read_bbt: Bad block at 0x000007fe0000
  560. [15:22:24]In:    serial
  561. [15:22:24]Out:   serial
  562. [15:22:24]Err:   serial
  563. [15:22:24]Net:   multi type
  564. [15:22:27]Internal phy firmware version: 0x853c
  565. [15:22:27]GRX500 Switch
  566. [15:22:27]
  567. [15:22:27]Type "run flash_nfs" to mount root filesystem over NFS
  568. [15:22:27]
  569. [15:22:27]
  570. [15:22:27]Press press hardware button for more than 4 seconds to run web failsafe mode
  571. [15:22:27]
  572. [15:22:27]
  573. [15:22:27]
  574. [15:22:27]Catution: hardware button wasn't pressed or not long enough!
  575. [15:22:27]Continuing normal boot...
  576. [15:22:27]
  577. [15:22:32]Hit any key to stop autoboot:  0
  578. [15:22:32]Creating 1 MTD partitions on "nand0":
  579. [15:22:32]0x000001340000-0x000007f40000 : "mtd=8"
  580. [15:22:32]UBI: attaching mtd1 to ubi0
  581. [15:22:32]UBI: physical eraseblock size:   131072 bytes (128 KiB)
  582. [15:22:32]UBI: logical eraseblock size:    126976 bytes
  583. [15:22:32]UBI: smallest flash I/O unit:    2048
  584. [15:22:32]UBI: VID header offset:          2048 (aligned 2048)
  585. [15:22:32]UBI: data offset:                4096
  586. [15:22:34]UBI: attached mtd1 to ubi0
  587. [15:22:34]UBI: MTD device name:            "mtd=8"
  588. [15:22:34]UBI: MTD device size:            108 MiB
  589. [15:22:34]UBI: number of good PEBs:        863
  590. [15:22:34]UBI: number of bad PEBs:         1
  591. [15:22:34]UBI: max. allowed volumes:       128
  592. [15:22:34]UBI: wear-leveling threshold:    4096
  593. [15:22:34]UBI: number of internal volumes: 1
  594. [15:22:34]UBI: number of user volumes:     6
  595. [15:22:34]UBI: available PEBs:             461
  596. [15:22:34]UBI: total number of reserved PEBs: 402
  597. [15:22:34]UBI: number of PEBs reserved for bad PEB handling: 8
  598. [15:22:34]UBI: max/mean erase counter: 90/12
  599. [15:22:34]Volume bootcoreB found at volume id 5
  600. [15:22:34]read 0 bytes from volume 5 to a0400000(buf address)
  601. [15:22:34]Read [2666496] bytes
  602. [15:22:35]Volume kernelB found at volume id 3
  603. [15:22:35]read 0 bytes from volume 3 to 80800000(buf address)
  604. [15:22:35]Read [3047424] bytes
  605. [15:22:37]## Booting kernel from Legacy Image at 80800000 ...
  606. [15:22:37]   Image Name:   MIPS LTQCPE Linux-3.10.102
  607. [15:22:37]   Created:      2017-06-16   3:18:48 UTC
  608. [15:22:37]   Image Type:   MIPS Linux Kernel Image (lzma compressed)
  609. [15:22:37]   Data Size:    3014592 Bytes = 2.9 MiB
  610. [15:22:37]   Load Address: a0020000
  611. [15:22:37]   Entry Point:  a002df00
  612. [15:22:37]   Verifying Checksum ... OK
  613. [15:22:40]   Uncompressing Kernel Image ... OK
  614. [15:22:40]
  615. [15:22:40]Starting kernel ...
  616. [15:22:40]
  617. [15:22:40][    0.000000] Initializing cgroup subsys cpu
  618. [15:22:40][    0.000000] Linux version 3.10.102 (jenkins@soho02) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 SMP Fri Jun 16 11:18:19 CST 2017
  619. [15:22:40][    0.000000] TLBINV/F supported, config4=0xc0000000
  620. [15:22:40][    0.000000] TLBINV/F supported, config4=0xc0000000
  621. [15:22:40][    0.000000] SoC: GRX500 rev 1.2
  622. [15:22:40][    0.000000] GCMP present
  623. [15:22:40][    0.000000] L2-only SYNC available
  624. [15:22:40][    0.000000] bootconsole [early0] enabled
  625. [15:22:40][    0.000000] CPU0 revision is: 0001a120 (MIPS interAptiv)
  626. [15:22:40][    0.000000] Enhanced Virtual Addressing (EVA 1GB) activated
  627. [15:22:40][    0.000000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000
  628. [15:22:40][    0.000000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001
  629. [15:22:40][    0.000000] BEV Overlay segment = 0xb0000000, size = 0x10000000
  630. [15:22:40][    0.000000] segctr0 2d0a0a segctr1 40d020a segctr2 38004d
  631. [15:22:40][    0.000000] MIPS: machine is EASY350 ANYWAN (GRX350) Router model
  632. [15:22:40][    0.000000] CMP IOCU detected
  633. [15:22:40][    0.000000] Hardware DMA cache coherency disabled
  634. [15:22:40][    0.000000] Determined physical RAM map:
  635. [15:22:40][    0.000000]  memory: 0e000000 [url=home.php?mod=space&uid=162986]@[/url] 20000000 (usable)
  636. [15:22:40][    0.000000] User-defined physical RAM map:
  637. [15:22:40][    0.000000]  memory: 0e000000 @ 20000000 (usable)
  638. [15:22:40][    0.000000] Initrd not found or empty - disabling initrd
  639. [15:22:40][    0.000000] reserving 18874368 bytes @ 6800a3c0 for CBM
  640. [15:22:40][    0.000000] reserving 8388608 bytes @ 6920a3c0 for CBM
  641. [15:22:40][    0.000000] Zone ranges:
  642. [15:22:40][    0.000000]   DMA      [mem 0x20000000-0x27ffffff]
  643. [15:22:40][    0.000000]   Normal   [mem 0x28000000-0x2dffffff]
  644. [15:22:40][    0.000000] Movable zone start for each node
  645. [15:22:40][    0.000000] Early memory node ranges
  646. [15:22:40][    0.000000]   node   0: [mem 0x20000000-0x2dffffff]
  647. [15:22:40][    0.000000] Detected 3 available secondary CPU(s)
  648. [15:22:40][    0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
  649. [15:22:40][    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  650. [15:22:40][    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  651. [15:22:40][    0.000000] PERCPU: Embedded 7 pages/cpu @69bce000 s7936 r8192 d12544 u32768
  652. [15:22:40][    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 56896
  653. [15:22:40][    0.000000] Kernel command line: ubi.mtd=system_sw rootfsname=rootfsB ro rootfstype=squashfs do_overlay console=ttyLTQ0,115200 ethaddr=2C:B2:1A:3D:14:14 panic=1 mtdparts=17c00000.nand-parts:1m(uboot),256k(ubootconfigA),256k(ubootconfigB),256k(gphyfirmware),1m(calibration),16m(bootcore),256k(pro_info),256k(dev_info),108m(system_sw),-(res) init=/etc/preinit active_bank=B update_chk=2 maxcpus=4 pci=pcie_bus_perf pcie_force_gen1=on ethwan= ubootver=U-Boot-2010.06-00044-gb399a23-LANTIQ-v-2.3.136 mem=224M@512M
  654. [15:22:41][    0.000000] eth0 mac address 2C-B2-1A-3D-14-14
  655. [15:22:41][    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
  656. [15:22:41][    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
  657. [15:22:41][    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
  658. [15:22:41][    0.000000] Writing ErrCtl register=00000000
  659. [15:22:41][    0.000000] Readback ErrCtl register=00000000
  660. [15:22:41][    0.000000] allocated 458752 bytes of page_cgroup
  661. [15:22:41][    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
  662. [15:22:41][    0.000000] Memory: 189712k/229376k available (6396k kernel code, 39664k reserved, 2219k data, 340k init, 0k highmem)
  663. [15:22:41][    0.000000] Hierarchical RCU implementation.
  664. [15:22:41][    0.000000] NR_IRQS:527
  665. [15:22:41][    0.000000] GIC: present
  666. [15:22:41][    0.000000] EIC: off
  667. [15:22:41][    0.000000] GIC map size 263
  668. [15:22:41][    0.000000] gic: revision 3.0
  669. [15:22:41][    0.000000] CPU0: c0 status register 1100fc00
  670. [15:22:41][    0.000000] of_gic_init init done
  671. [15:22:41][    0.000000] CPU Clock: 800000000Hz  mips_hpt_frequency 400000000Hz
  672. [15:22:41][    0.000000] CBM Clock: 600000000Hz DDR Clock: 666666666Hz NGI Clock: 300000000Hz
  673. [15:22:41][    0.000000] clock event init done !
  674. [15:22:41][    0.000000] gptu_setup_clocksource: done !
  675. [15:22:41][    0.000000] Calibrating delay loop... 513.63 BogoMIPS (lpj=2568192)
  676. [15:22:41][    0.070000] pid_max: default: 32768 minimum: 301
  677. [15:22:41][    0.070000] Mount-cache hash table entries: 512
  678. [15:22:41][    0.080000] Initializing cgroup subsys memory
  679. [15:22:41][    0.080000] size of core = 336, MAXCORE = 2 , MAXCPU = 4, MAXTCS = 6 MAX_VPE = 2
  680. [15:22:41][    0.090000] [update_DB_from_DT]:[363], cpuid = 0 name = LINUX
  681. [15:22:41][    0.090000] [update_DB_from_DT]:[363], cpuid = 1 name = LINUX
  682. [15:22:41][    0.100000] [update_DB_from_DT]:[363], cpuid = 2 name = LINUX
  683. [15:22:41][    0.100000] [update_DB_from_DT]:[363], cpuid = 3 name = MPEFW
  684. [15:22:41][    0.110000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 1
  685. [15:22:41][    0.110000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 2
  686. [15:22:41][    0.120000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 3
  687. [15:22:41][    0.120000]
  688. [15:22:41][    0.120000] Initial ITC_Address_Map0 00000000
  689. [15:22:41][    0.130000]
  690. [15:22:41]def ITC_Address_Map1 01200000
  691. [15:22:41]new ITC_Address_Map1 0120fc00
  692. [15:22:41]def ITC_Address_Map0 00000000
  693. [15:22:41]new ITC_Address_Map0 1c300001
  694. [15:22:41] ITC Init done on Core 0 on CPU 0 !!!
  695. [15:22:41][    0.140000] [vmb_cpu_alloc]:[624] CPU vpet.cpu_status = 11
  696. [15:22:41][    0.150000] [vmb_cpu_start]:[842]  vmb_fw_msg_t = a00000b8 cpu = 1 vmb_msg_size = b0 sizeof(VMB_fw_msg_t) = 168 sizeof(FW_vmb_msg_t) = 8 !!!!
  697. [15:22:41] [gic_trigger]:[551] VMB_CPU_IPI1 - 20 CPU = 1
  698. [15:22:41]
  699. [15:22:41]Outside WAIT got IPI interrupt to launch from cpu 01
  700. [15:22:41]
  701. [15:22:41] MSG_ID = 01[    0.160000] [vmb_cpu_start]:[881] WAITING FOR RESPONSE vpet->v_wq.wakeup_vpe = 0 !!!!
  702. [15:22:41] [    0.160000] TLBINV/F supported, config4=0xc0000000
  703. [15:22:41][    0.160000] TLBINV/F supported, config4=0xc0000000
  704. [15:22:41][    0.160000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
  705. [15:22:41][    0.160000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  706. [15:22:41][    0.160000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  707. [15:22:41][    0.160000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000
  708. [15:22:41][    0.160000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001
  709. [15:22:41][    0.160000] BEV Overlay segment = 0xb0000000, size = 0x10000000
  710. [15:22:41][    0.160000]
  711. [15:22:41][    0.160000] Initial ITC_Address_Map0 1c300001
  712. [15:22:41][    0.160000] ITC Memory is already initialised for Core 0 at address 1c300000 !!![    0.160000] CPU1 revision is: 0001a120 (MIPS interAptiv)
  713. [15:22:41]
  714. [15:22:41][    0.220000] [vmb_cpu_active]:[268] action = 10 , cpu = 1
  715. [15:22:41][    0.220000] [vmb_cpu_start]:[898] OUTSIDE WAIT wakeup_vpe = 1 vpet->fw_vmb.status = 1 ACK = 1 cpu = 1 ret1 = 9995 vpet = 608e3a98, smp_processor_id() = 0 , vpet->fw_vmb =608e3ac4 !!!!
  716. [15:22:41][    0.220000]  [vmb_cpu_start]:[905]  ret = 1
  717. [15:22:41]
  718. [15:22:41][    0.230000] Synchronize counters for CPU 1: done.
  719. [15:22:41][    0.230000] GPTC clock event init on cpu: 1
  720. [15:22:41][    0.230000] clock event init done !
  721. [15:22:41][    0.240000] [vmb_cpu_alloc]:[624] CPU vpet.cpu_status = 11
  722. [15:22:41][    0.240000] [vmb_cpu_start]:[842]  vmb_fw_msg_t = a0000168 cpu = 2 vmb_msg_size = b0 sizeof(VMB_fw_msg_t) = 168 sizeof(FW_vmb_msg_t) = 8 !!!!
  723. [15:22:41] [gic_trigger]:[555] VMB_CPU_IPI2 - 21 CPU = 2
  724. [15:22:41]
  725. [15:22:41]Outside WAIT got IPI interrupt to launch from cpu 02
  726. [15:22:41]
  727. [15:22:41] MSG_ID = 01[    0.250000] [vmb_cpu_start]:[881] WAITING FOR RESPONSE vpet->v_wq.wakeup_vpe = 0 !!!!
  728. [15:22:41] [    0.250000] TLBINV/F supported, config4=0xc0000000
  729. [15:22:41][    0.250000] TLBINV/F supported, config4=0xc0000000
  730. [15:22:41][    0.250000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
  731. [15:22:41][    0.250000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
  732. [15:22:41][    0.250000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
  733. [15:22:41][    0.250000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000
  734. [15:22:41][    0.250000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001
  735. [15:22:41][    0.250000] BEV Overlay segment = 0xb0000000, size = 0x10000000
  736. [15:22:41][    0.250000]
  737. [15:22:41][    0.250000] Initial ITC_Address_Map0 00000000
  738. [15:22:41][    0.250000]
  739. [15:22:41][    0.250000] def ITC_Address_Map1 01200000
  740. [15:22:41][    0.250000] new ITC_Address_Map1 0120fc00
  741. [15:22:41][    0.250000] def ITC_Address_Map0 00000000
  742. [15:22:41][    0.250000] new ITC_Address_Map0 1c300001
  743. [15:22:41][    0.250000]  ITC Init done on Core 1 on CPU 2 !!!
  744. [15:22:41][    0.250000] CPU2 revision is: 0001a120 (MIPS interAptiv)
  745. [15:22:41]
  746. [15:22:41][    0.310000] [vmb_cpu_active]:[268] action = 10 , cpu = 2
  747. [15:22:41][    0.310000] [vmb_cpu_start]:[898] OUTSIDE WAIT wakeup_vpe = 1 vpet->fw_vmb.status = 1 ACK = 1 cpu = 2 ret1 = 9995 vpet = 608e3b08, smp_processor_id() = 0 , vpet->fw_vmb =608e3b34 !!!!
  748. [15:22:41][    0.310000]  [vmb_cpu_start]:[905]  ret = 1
  749. [15:22:41]
  750. [15:22:41][    0.320000] Synchronize counters for CPU 2: done.
  751. [15:22:41][    0.320000] GPTC clock event init on cpu: 2
  752. [15:22:41][    0.320000] clock event init done !
  753. [15:22:41][    0.330000] [smp_init]:[553] CPU3 shouldn't run LINUX as per DT (model) config
  754. [15:22:41][    0.330000] Brought up 3 CPUs
  755. [15:22:41][    0.350000] pinctrl core: initialized pinctrl subsystem
  756. [15:22:41][    0.350000] regulator-dummy: no parameters
  757. [15:22:41][    0.360000] NET: Registered protocol family 16
  758. [15:22:41][    0.360000] [gpio_xrx500] { xrx500_gpio_init : 407 }XRX500 GPIO Driver, (C) 2014 Lantiq Deutschland Gmbh
  759. [15:22:41][    0.370000] dma-grx500 1e300000.dma: DMA3 base address be300000 chained_irq 77 irq_base 447
  760. [15:22:41][    0.380000] dma-grx500 1e300000.dma: Init done - hw rev: A, ports: 1, channels: 64
  761. [15:22:41][    0.390000] dma-grx500 1c100000.dma: DMA2TX base address bc100000 chained_irq 75 irq_base 399
  762. [15:22:41][    0.400000] dma-grx500 1c100000.dma: Init done - hw rev: A, ports: 1, channels: 16
  763. [15:22:41][    0.400000] dma-grx500 1c200000.dma: DMA2RX base address bc200000 chained_irq 76 irq_base 415
  764. [15:22:41][    0.410000] dma-grx500 1c200000.dma: Init done - hw rev: A, ports: 1, channels: 32
  765. [15:22:41][    0.420000] dma-grx500 1a100000.dma: DMA1TX base address ba100000 chained_irq 73 irq_base 351
  766. [15:22:41][    0.430000] dma-grx500 1a100000.dma: Init done - hw rev: A, ports: 1, channels: 16
  767. [15:22:41][    0.430000] dma-grx500 1a200000.dma: DMA1RX base address ba200000 chained_irq 74 irq_base 367
  768. [15:22:41][    0.440000] dma-grx500 1a200000.dma: Init done - hw rev: A, ports: 1, channels: 12
  769. [15:22:41][    0.450000] [gptu] { gptu_probe : 297 }dev id 16b00000.gptu
  770. [15:22:41][    0.460000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded
  771. [15:22:41][    0.460000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded
  772. [15:22:41][    0.470000] gptu-xrx500 16b00000.gptu: gptu: 2 timers loaded
  773. [15:22:41][    0.470000] gptu driver init successfully
  774. [15:22:41][    0.480000] [gptu] { gptu_probe : 297 }dev id 16300000.gptu
  775. [15:22:41][    0.480000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded
  776. [15:22:41][    0.490000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded
  777. [15:22:41][    0.490000] gptu-xrx500 16300000.gptu: gptu: 2 timers loaded
  778. [15:22:41][    0.500000] gptu driver init successfully
  779. [15:22:41][    0.500000] dma0-grx500 16e00000.dma: base address b6e00000 chained_irq 72 irq_base 335
  780. [15:22:41][    0.510000] dma0-grx500 16e00000.dma: Init done - hw rev: A, ports: 4, channels: 16
  781. [15:22:41][    0.510000] [pinctrl_xrx500] { pinctrl_xrx500_probe : 1243 }disabling the BBSPI at top-mux
  782. [15:22:41][    0.520000] pinctrl-xrx500 pinctrl.4: Init done
  783. [15:22:41][    0.530000] !!!!!!! WAVE400 system registeration on AHB
  784. [15:22:41][    0.530000] MTLK_MEM_BAR1_START is 14000000
  785. [15:22:41][    0.540000] MTLK_MEM_BAR1_END is 147fffff
  786. [15:22:41][    0.540000] MTLK_WIRELESS_IRQ_IN_INDEX is 26
  787. [15:22:41][    0.540000] [cbm] { cbm_xrx500_probe : 5346 }2
  788. [15:22:41][    0.550000] Initializing TMU with Base Address=be700000: ...
  789. [15:22:41][    0.550000] TMU Initialization Done
  790. [15:22:41][    0.560000] [cbm] { init_fsqm_buf_standard : 655 }init fsqm std successfully
  791. [15:22:42][    0.560000] [cbm] { init_fsqm_buf_jumbo : 698 }init fsqm jbo successfully
  792. [15:22:42][    0.570000] [cbm] { init_fsqm : 581 }fsqm init successfully
  793. [15:22:42][    0.570000] [cbm] { init_cbm_basic : 771 }init basic CBM successfully
  794. [15:22:42][    0.580000] [cbm] { cbm_hw_init : 1946 }CBM HW init
  795. [15:22:42][    0.580000] [cbm] { setup_DMA_p2p : 4733 }setup_DMA_p2p executed
  796. [15:22:42][    0.590000] [cbm] { configure_ports : 5187 }configure_ports 7 1 0 0 8 2
  797. [15:22:42][    0.590000] [cbm] { configure_ports : 5154 }configure_ports 7 1 16 1 8 2
  798. [15:22:42][    0.600000] [cbm] { configure_ports : 5187 }configure_ports 8 1 15 0 8 2
  799. [15:22:42][    0.600000] [cbm] { configure_ports : 5154 }configure_ports 8 1 31 1 8 2
  800. [15:22:42][    0.610000] [cbm] { init_cbm_ls : 1124 }Load spreader init successfully
  801. [15:22:42][    0.610000] [cbm] { cbm_xrx500_probe : 5409 }CBM Clock: 600000000Hz
  802. [15:22:42][    0.620000] [cbm] { cbm_xrx500_probe : 5411 }EQM delay Enabled
  803. [15:22:42][    0.620000] [cbm] { cbm_xrx500_probe : 5477 }CBM: Init Done !!
  804. [15:22:42][    0.630000] PCI host bridge /ssx3@18000000/pcie@900000 ranges:
  805. [15:22:42][    0.630000]  MEM 0x00000000b8000000..0x00000000baffffff
  806. [15:22:42][    0.640000]   IO 0x00000000bb800000..0x00000000bb8fffff
  807. [15:22:42][    0.740000] PCIe LCPLL SSC Mode Enabled
  808. [15:22:42][    1.250000] pcie_wait_phy_link_up port 0 timeout
  809. [15:22:42][    1.250000] pcie_rc_initialize port 0 link up failed!!!!!
  810. [15:22:42][    1.260000] Lantiq PCIe Root Complex Port 0 Init Done
  811. [15:22:42][    1.260000] PCI host bridge /ssx3@18000000/pcie@400000 ranges:
  812. [15:22:42][    1.270000]  MEM 0x00000000b4000000..0x00000000b6ffffff
  813. [15:22:42][    1.270000]   IO 0x00000000b7800000..0x00000000b78fffff
  814. [15:22:43][    1.880000] pcie_wait_phy_link_up port 1 timeout
  815. [15:22:43][    1.880000] pcie_rc_initialize port 1 link up failed!!!!!
  816. [15:22:43][    1.890000] Lantiq PCIe Root Complex Port 1 Init Done
  817. [15:22:43][    1.890000] PCI host bridge /ssx3@18000000/pcie@E00000 ranges:
  818. [15:22:43][    1.900000]  MEM 0x00000000bc000000..0x00000000beffffff
  819. [15:22:43][    1.900000]   IO 0x00000000bf800000..0x00000000bf8fffff
  820. [15:22:43][    2.510000] pcie_wait_phy_link_up port 2 timeout
  821. [15:22:43][    2.510000] pcie_rc_initialize port 2 link up failed!!!!!
  822. [15:22:43][    2.520000] Lantiq PCIe Root Complex Port 2 Init Done
  823. [15:22:43][    2.540000] bio: create slab <bio-0> at 0
  824. [15:22:43][    2.550000] vgaarb: loaded
  825. [15:22:43][    2.550000] SCSI subsystem initialized
  826. [15:22:43][    2.550000] Register xway nand done!
  827. [15:22:43][    2.560000] usbcore: registered new interface driver usbfs
  828. [15:22:43][    2.560000] usbcore: registered new interface driver hub
  829. [15:22:43][    2.570000] usbcore: registered new device driver usb
  830. [15:22:43][    2.570000] i2c-lantiq 16a00000.i2c: pins are not configured from the driver
  831. [15:22:43][    2.580000] i2c-lantiq 16a00000.i2c: setup clocks (in 200000000 kHz, bus 100000 kHz,rmc =20 dec=50 10000000)
  832. [15:22:43][    2.590000] i2c-lantiq 16a00000.i2c: version 1.01
  833. [15:22:44][    2.610000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  834. [15:22:44][    2.630000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  835. [15:22:44][    2.650000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  836. [15:22:44][    2.650000] 1V15VDD: 900 <--> 1200 mV at 1790 mV normal standby
  837. [15:22:44][    2.680000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  838. [15:22:44][    2.700000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  839. [15:22:44][    2.720000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  840. [15:22:44][    2.740000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  841. [15:22:44][    2.760000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  842. [15:22:44][    2.760000] try to register spd_mon driver
  843. [15:22:44][    2.770000] spdmon 16080110.speedm: base address: 0xb6080110
  844. [15:22:44][    2.770000] spdmon 16080110.speedm: PHY base address: 0x16080110
  845. [15:22:44][    2.780000] device number :253
  846. [15:22:44][    2.780000] spdmon 16080110.speedm: spd_mon driver : init done !!
  847. [15:22:44][    2.790000] spd_mon driver registered
  848. [15:22:44][    2.800000] NET: Registered protocol family 8
  849. [15:22:44][    2.800000] NET: Registered protocol family 20
  850. [15:22:44][    2.810000] cfg80211: Calling CRDA to update world regulatory domain
  851. [15:22:44][    2.810000] Switching to clocksource gptc-timer
  852. [15:22:44][    2.840000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  853. [15:22:44][    2.860000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  854. [15:22:44][    2.880000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  855. [15:22:44][    2.900000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  856. [15:22:44][    2.920000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  857. [15:22:44][    2.940000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  858. [15:22:44][    2.940000] ltq_regulator_cpufreq: rcf_debugfs_init is called
  859. [15:22:44][    2.950000] NET: Registered protocol family 2
  860. [15:22:44][    2.950000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
  861. [15:22:44][    2.960000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
  862. [15:22:44][    2.970000] TCP: Hash tables configured (established 2048 bind 2048)
  863. [15:22:44][    2.970000] TCP: reno registered
  864. [15:22:44][    2.980000] UDP hash table entries: 256 (order: 1, 8192 bytes)
  865. [15:22:44][    2.980000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  866. [15:22:44][    2.990000] NET: Registered protocol family 1
  867. [15:22:44][    2.990000] RPC: Registered named UNIX socket transport module.
  868. [15:22:44][    3.000000] RPC: Registered udp transport module.
  869. [15:22:44][    3.000000] RPC: Registered tcp transport module.
  870. [15:22:44][    3.010000] RPC: Registered tcp NFSv4.1 backchannel transport module.
  871. [15:22:44][    3.020000] phy-xrx500 phy-xrx500.10: requesting lantiq/phy11g_ip_BE.bin
  872. [15:22:44][    3.020000] phy-xrx500 phy-xrx500.10: booting GPHY0 firmware at 27C20000 for GRX500
  873. [15:22:44][    3.130000] phy-xrx500 phy-xrx500.10: booting GPHY1 firmware at 27C20000 for GRX500
  874. [15:22:44][    3.230000] phy-xrx500 phy-xrx500.10: booting GPHY2 firmware at 27C20000 for GRX500
  875. [15:22:44][    3.340000] phy-xrx500 phy-xrx500.10: booting GPHY3 firmware at 27C20000 for GRX500
  876. [15:22:44][    3.440000] phy-xrx500 phy-xrx500.10: booting GPHY4 firmware at 27C20000 for GRX500
  877. [15:22:44][    3.550000] audit: initializing netlink socket (disabled)
  878. [15:22:44][    3.550000] type=2000 audit(3.540:1): initialized
  879. [15:22:44][    3.560000] VFS: Disk quotas dquot_6.5.2
  880. [15:22:44][    3.560000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  881. [15:22:44][    3.570000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  882. [15:22:44][    3.580000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
  883. [15:22:44][    3.580000] msgmni has been set to 370
  884. [15:22:44][    3.590000] io scheduler noop registered
  885. [15:22:44][    3.590000] io scheduler deadline registered (default)
  886. [15:22:44][    3.600000] io scheduler cfq registered
  887. [15:22:45][    3.600000] [vmb_yr_get]:[1362] CPU = 0, yri[i].yr_status = 1, yield_bits = 1 n_yr = 1 yri[i].cpu_id = 0
  888. [15:22:45][    3.610000] [vmb_yr_get]:[1362] CPU = 1, yri[i].yr_status = 1, yield_bits = 2 n_yr = 1 yri[i].cpu_id = 1
  889. [15:22:45][    3.620000] [vmb_yr_get]:[1362] CPU = 2, yri[i].yr_status = 1, yield_bits = 1 n_yr = 1 yri[i].cpu_id = 2
  890. [15:22:45][    3.630000] UMT initialize success!
  891. [15:22:45][    3.640000] HW MCPY driver: Version: 1.1.0, Init Done !!
  892. [15:22:45][    3.640000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
  893. [15:22:45][    3.650000] lantiq,asc 16600000.serial: pins are not configured from the driver
  894. [15:22:45][    3.660000] 16600000.serial: ttyLTQ0 at MMIO 0x16600000 (irq = 111) is a lantiq,asc
  895. [15:22:45][    3.670000] console [ttyLTQ0] enabled, bootconsole disabled
  896. [15:22:45][    3.670000] console [ttyLTQ0] enabled, bootconsole disabled
  897. [15:22:45][    3.680000] Lantiq MIPSInterAptiv MPS driver, version 1.0.0.0, (c) 2006-2013 Lantiq Deutschland GmbH
  898. [15:22:45][    3.690000] MPS: major Id 251
  899. [15:22:45][    3.700000] Major Id is 250
  900. [15:22:45][    3.700000] ICC driver registered
  901. [15:22:45][    3.700000] sysrst_init: Trying to register System Reset Driver ...
  902. [15:22:45][    3.710000] sysrst_pre_init: Detect InterAptiv CPU ...
  903. [15:22:45][    3.710000] sysrst_init: Lantiq CPE GRX500 System driver version 1.0.0
  904. [15:22:45][    3.720000] sysrst_init: GRX500 System Reset initialized successfully!
  905. [15:22:45][    3.730000] brd: module loaded
  906. [15:22:45][    3.730000] loop: module loaded
  907. [15:22:45][    3.730000] Uniform Multi-Platform E-IDE driver
  908. [15:22:45][    3.740000] ide-gd driver 1.18
  909. [15:22:45][    3.740000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
  910. [15:22:45][    3.750000] Scanning device for bad blocks
  911. [15:22:45][    3.820000] Bad eraseblock 515 at 0x000004060000
  912. [15:22:45][    3.890000] Bad eraseblock 1023 at 0x000007fe0000
  913. [15:22:45][    3.890000] 10 cmdlinepart partitions found on MTD device 17c00000.nand-parts
  914. [15:22:45][    3.900000] Creating 10 MTD partitions on "17c00000.nand-parts":
  915. [15:22:45][    3.900000] 0x000000000000-0x000000100000 : "uboot"
  916. [15:22:45][    3.910000] 0x000000100000-0x000000140000 : "ubootconfigA"
  917. [15:22:45][    3.910000] 0x000000140000-0x000000180000 : "ubootconfigB"
  918. [15:22:45][    3.920000] 0x000000180000-0x0000001c0000 : "gphyfirmware"
  919. [15:22:45][    3.920000] 0x0000001c0000-0x0000002c0000 : "calibration"
  920. [15:22:45][    3.930000] 0x0000002c0000-0x0000012c0000 : "bootcore"
  921. [15:22:45][    3.930000] 0x0000012c0000-0x000001300000 : "pro_info"
  922. [15:22:45][    3.940000] 0x000001300000-0x000001340000 : "dev_info"
  923. [15:22:45][    3.940000] 0x000001340000-0x000007f40000 : "system_sw"
  924. [15:22:45][    3.950000] 0x000007f40000-0x000008000000 : "res"
  925. [15:22:45][    3.960000] Gluebi: Found kernel commandline option 'rootfsname=rootfsB'
  926. [15:22:45][    3.960000] spi-lantiq-ssc 16800000.spi: master is unqueued, this is deprecated
  927. [15:22:45][    3.970000] Lantiq SoC SPI controller rev 9 (TXFS 32, RXFS 32, DMA 1)
  928. [15:22:45][    3.980000] [ltq_ssc] { ifx_ssc_init : 3802 }[ifx_ssc_init] force ifx_ssc_cs_low to PORT 1
  929. [15:22:45][    3.980000] [ltq_ssc] { ifx_ssc_init : 3803 }[ifx_ssc_init] force ifx_ssc_cs_high to PORT 1
  930. [15:22:45][    3.990000] [ltq_ssc] { ifx_ssc_init : 3807 }ifx_ssc_init ifx_ssc_init_count 1
  931. [15:22:45][    4.000000] [ltq_ssc] { ifx_ssc_init : 3930 }port name ltq_ssc1
  932. [15:22:45][    4.000000] [ltq_ssc] { ifx_ssc_init : 4026 }Lantiq SoC SSC controller rev 9 (TXFS 32, RXFS 32, DMA 1)
  933. [15:22:45][    4.010000] [ltq_ssc] { ifx_sscAllocConnection : 3511 }ifx_sscAllocConnection ssc driver must be loaded first!
  934. [15:22:45][    4.020000] ifx_spi_flash_init: failed to register sflash
  935. [15:22:45][    4.030000] IMQ driver loaded successfully. (numdevs = 3, numqueues = 1)
  936. [15:22:45][    4.040000]  Hooking IMQ after NAT on PREROUTING.
  937. [15:22:45][    4.040000]  Hooking IMQ after NAT on POSTROUTING.
  938. [15:22:45][    4.050000] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
  939. [15:22:45][    4.060000] Lantiq VRX318 Version 3.0.0
  940. [15:22:45][    4.060000] LTQ ETH SWITCH API, Version 3.0.2.
  941. [15:22:45][    4.060000] SWAPI: Registered char device [switch_api] with major no [81]
  942. [15:22:45][    4.070000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1717 (pnum:7)
  943. [15:22:45][    4.080000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1784 (gswdev->gipver:48)
  944. [15:22:45][    4.090000] LTQ ETH SWITCH API, Version 3.0.2.
  945. [15:22:45][    4.090000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1717 (pnum:2)
  946. [15:22:45][    4.100000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1784 (gswdev->gipver:48)
  947. [15:22:45][    4.120000] gphy_driver_init: fw_mode:11G-FW, no of phys:5, mode:0
  948. [15:22:45][    4.120000] [datapath_loopeth_dev] { dp_loop_eth_dev_init : 1686 }Loading loop_net_dev driver ......
  949. [15:22:45][    4.130000] [datapath_loopeth_dev] { dp_loop_eth_dev_init : 1692 }dp_loop_eth_dev_init Succeeded!
  950. [15:22:45][    4.140000] [datapath_coc] { dp_coc_new_stat_req : 786 }COC is not initialized yet in DP
  951. [15:22:45][    4.150000] dp init done
  952. [15:22:45][    4.150000] PMAC_EG_CFG_SET for GSW-L
  953. [15:22:45][    4.150000] PMAC_IG_CFG_SET for GSW-L
  954. [15:22:45][    4.160000] PMAC_EG_CFG_SET for GSW-R
  955. [15:22:45][    4.170000] PMAC_IG_CFG_SET for GSW-R
  956. [15:22:45][    4.170000]
  957. [15:22:45][    4.170000]   GSW PMAC Init Done!!!
  958. [15:22:45][    4.170000] registering one of MII bus
  959. [15:22:45][    4.180000] libphy: lantiq,xrx500-mdio: probed
  960. [15:22:45][    4.190000] registering PAE MII bus
  961. [15:22:45][    4.200000] libphy: lantiq,xrx500-mdio-pae: probed
  962. [15:22:45][    4.200000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  963. [15:22:45][    4.210000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  964. [15:22:45][    4.210000] xrx500_of_iface: rx csum offload is enabled !
  965. [15:22:45][    4.220000] trying to connect: eth0_1 to device: 0:02 with irq: 120
  966. [15:22:45][    4.270000] eth0_1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:02, irq=120)
  967. [15:22:45][    4.290000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  968. [15:22:45][    4.290000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  969. [15:22:45][    4.300000] xrx500_of_iface: rx csum offload is enabled !
  970. [15:22:45][    4.300000] trying to connect: eth0_2 to device: 0:03 with irq: 121
  971. [15:22:45][    4.350000] eth0_2: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:03, irq=121)
  972. [15:22:45][    4.370000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  973. [15:22:45][    4.370000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  974. [15:22:45][    4.380000] xrx500_of_iface: rx csum offload is enabled !
  975. [15:22:45][    4.380000] trying to connect: eth0_3 to device: 0:04 with irq: 134
  976. [15:22:45][    4.430000] eth0_3: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:04, irq=134)
  977. [15:22:45][    4.450000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  978. [15:22:45][    4.460000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  979. [15:22:45][    4.460000] xrx500_of_iface: rx csum offload is enabled !
  980. [15:22:45][    4.470000] trying to connect: eth0_4 to device: 0:05 with irq: 135
  981. [15:22:45][    4.510000] eth0_4: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:05, irq=135)
  982. [15:22:45][    4.530000] [cbm] { cbm_dp_port_alloc : 3074 }guess first time
  983. [15:22:45][    4.540000] [cbm] { cbm_dp_port_alloc : 3080 }1024
  984. [15:22:45][    4.540000] xrx500_of_iface: rx csum offload is enabled !
  985. [15:22:45][    4.550000] trying to connect: eth1 to device: 1:01 with irq: 119
  986. [15:22:45][    4.590000] eth1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=1:01, irq=119)
  987. [15:22:46][    4.610000] register mc group pass: 0, grp name: eth_mcgrp, grp id:6
  988. [15:22:46][    4.620000] Lantiq ethernet driver for XRX500 !
  989. [15:22:46][    4.620000] lro_sram_membase_res0 from DT: a2013000
  990. [15:22:46][    4.630000] ltq_toe_membase: e2000000 and lro_sram_membase_res0: e2013000
  991. [15:22:46][    4.630000] TOE Init Done !!
  992. [15:22:46][    4.640000] PPP generic driver version 2.4.2
  993. [15:22:46][    4.640000] PPP BSD Compression module registered
  994. [15:22:46][    4.640000] PPP Deflate Compression module registered
  995. [15:22:46][    4.650000] PPP MPPE Compression module registered
  996. [15:22:46][    4.650000] NET: Registered protocol family 24
  997. [15:22:46][    4.660000] ltq-dwc3-core 1a300000.usb: no usb3 phy configured
  998. [15:22:46][    4.660000] platform 1a300000.usb: Driver ltq-dwc3-core requests probe deferral
  999. [15:22:46][    4.670000] ltq-dwc3-core 1a500000.usb: no usb3 phy configured
  1000. [15:22:46][    4.680000] platform 1a500000.usb: Driver ltq-dwc3-core requests probe deferral
  1001. [15:22:46][    4.690000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  1002. [15:22:46][    4.690000] ehci-pci: EHCI PCI platform driver
  1003. [15:22:46][    4.700000] uhci_hcd: USB Universal Host Controller Interface driver
  1004. [15:22:46][    4.700000] usbcore: registered new interface driver usb-storage
  1005. [15:22:46][    4.710000] usbcore: registered new interface driver ums-alauda
  1006. [15:22:46][    4.710000] usbcore: registered new interface driver ums-datafab
  1007. [15:22:46][    4.720000] usbcore: registered new interface driver ums-freecom
  1008. [15:22:46][    4.730000] usbcore: registered new interface driver ums-jumpshot
  1009. [15:22:46][    4.730000] usbcore: registered new interface driver ums-sddr09
  1010. [15:22:46][    4.740000] usbcore: registered new interface driver ums-sddr55
  1011. [15:22:46][    4.740000] usbcore: registered new interface driver ums-usbat
  1012. [15:22:46][    4.750000] mousedev: PS/2 mouse device common for all mice
  1013. [15:22:46][    4.760000] i2c-lantiq 16a00000.i2c: Register I2CCOCDRV to CPUFREQ.
  1014. [15:22:46][    4.780000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  1015. [15:22:46][    4.800000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready
  1016. [15:22:46][    4.800000] ina2xx 0-0040: power monitor: ina219, railname:  PWR_12V, Rshunt: 10000 uOhm
  1017. [15:22:46][    4.810000] [gptu] { setrate : 154 }cpu_clk 200000000
  1018. [15:22:46][    4.810000] [gptu] { setrate : 158 }reload_counter_value 1
  1019. [15:22:46][    4.820000] gpio-sso-xrx500 16d00000.sso: pins are not configured from the driver
  1020. [15:22:46][    4.830000] gpio-sso-xrx500 16d00000.sso: Init done
  1021. [15:22:46][    4.830000] Device IRQ: 97 line: 100
  1022. [15:22:46][    4.830000] GlobalControl97_Capabilities_Get
  1023. [15:22:46][    4.840000] EIP202: PEs=1 rings=4 64-bit=No, fill level extension=No
  1024. [15:22:46][    4.840000] CF size=4 RF size=3 DMA len = 10 Align=0 HDW=0 HostIfc=3
  1025. [15:22:46][    4.850000] EIP96 options:
  1026. [15:22:46][    4.850000] AES: Yes with CFB/OFB: Yes Fast: Yes
  1027. [15:22:46][    4.850000] DES: Yes with CFB/OFB: Yes Fast: No
  1028. [15:22:46][    4.850000] ARCFOUR level: 3
  1029. [15:22:46][    4.850000] MD5: Yes SHA1: Yes Fast: Yes SHA256: Yes SHA512: Yes
  1030. [15:22:46][    4.850000] (X)CBC-MAC: Yes Fast: Yes All key sizes: No GHASH Yes
  1031. [15:22:46][    4.880000] EIP97 options: PEs=1, In Dbuf size=6 In Tbuf size=5, Out Dbuf size=6, Out Tbuf size=4,
  1032. [15:22:46][    4.880000] Token Generator: No, Transform Record Cache: No
  1033. [15:22:46][    4.890000] EIP206 options: PE type=0 InClassifier=0 OutClassifier=0 MAC chans=0
  1034. [15:22:46][    4.890000] InDBuf=0kB InTBuf=0kB OutDBuf=0kB OutTBuf=0kB
  1035. [15:22:46][    4.910000] Global EIP-97 capabilities: EIP-97 v1.2p1  with EIP-202 v1.3p0 and EIP-96 v2.2p3, #PE=01 #rings=04
  1036. [15:22:46][    4.920000] Global Status of the EIP-97
  1037. [15:22:46][    4.920000] Packet Engine 0 Status
  1038. [15:22:46][    4.920000] DFE Status: CD FIFO Words: 0, CDR ID: 15, DMA size: 0
  1039. [15:22:46][    4.920000] AtDMA busy: false, DataDMA busy: false, DMA err: false
  1040. [15:22:46][    4.930000] DSE Status: RD FIFO Words: 0, RDR ID: 15, DMA size: 0
  1041. [15:22:46][    4.930000] Data flush  busy: false, DataDMA busy: false, DMA err: false
  1042. [15:22:46][    4.950000] Token Status: Active: 0, loc available: true
  1043. [15:22:46][    4.950000] res available: false, read active: false, ccache active: false
  1044. [15:22:46][    4.950000] cntx fetch: false, res cntx: false
  1045. [15:22:46][    4.950000] processing held: true, busy: false
  1046. [15:22:46][    4.970000] Context Status: Err mask: 0000, Available: 0
  1047. [15:22:46][    4.970000] Active cntx: false, next cntx: false, result cntx: false Err recov: false
  1048. [15:22:46][    4.980000] Interrupt Status: input DMA err: false, output DMA err false
  1049. [15:22:46][    4.980000] pkt proc err: false, pkt timeout: false, f a t a l err: false, PE int out: false
  1050. [15:22:46][    4.980000] inp DMA enable: false, outp DMA enable false, pkt proc enable: false
  1051. [15:22:46][    4.980000] pkt timeout enable: false, f a t a l enable: false,PE int out enable: false
  1052. [15:22:46][    5.010000] Output Transfer Status: availabe: 71, min: 8, max: 64, size mask: 252
  1053. [15:22:46][    5.020000] PRNG Status: busy: true, res ready: false
  1054. [15:22:46][    5.020000] Adapter_Lock_Alloc: Lock = spinlock
  1055. [15:22:46][    5.030000] Adapter_Lock_Alloc: Lock = spinlock
  1056. [15:22:46][    5.030000] Adapter_PECDev_Init: CDR fetch size 0x8, thresh 0x6, HDW=0, CFsize=4
  1057. [15:22:46][    5.040000] Adapter_PECDev_Init: RDR fetch size 0x8, thresh 0x2, RFsize=3
  1058. [15:22:46][    5.050000] Status of CDR/RDR interface 0
  1059. [15:22:46][    5.050000] CDR Status: DMA err: false, err: false: ovf/under err: false
  1060. [15:22:46][    5.050000] Threshold int: false, timeout int: false, FIFO count: 16
  1061. [15:22:46][    5.070000] RDR Status: DMA err: false, err: false: ovf/under err: false
  1062. [15:22:46][    5.070000] Buf ovf: false, Descriptor ovf false
  1063. [15:22:46][    5.070000] Threshold int: false, timeout int: false, FIFO count: 8
  1064. [15:22:46][    5.080000] Adapter_Lock_Alloc: Lock = spinlock
  1065. [15:22:46][    5.090000] Adapter_Lock_Alloc: Lock = spinlock
  1066. [15:22:46][    5.090000] Adapter_PECDev_Init: CDR fetch size 0x8, thresh 0x6, HDW=0, CFsize=4
  1067. [15:22:46][    5.100000] Adapter_PECDev_Init: RDR fetch size 0x8, thresh 0x2, RFsize=3
  1068. [15:22:46][    5.110000] Status of CDR/RDR interface 1
  1069. [15:22:46][    5.110000] CDR Status: DMA err: false, err: false: ovf/under err: false
  1070. [15:22:46][    5.110000] Threshold int: false, timeout int: false, FIFO count: 16
  1071. [15:22:46][    5.120000] RDR Status: DMA err: false, err: false: ovf/under err: false
  1072. [15:22:46][    5.120000] Buf ovf: false, Descriptor ovf false
  1073. [15:22:46][    5.120000] Threshold int: false, timeout int: false, FIFO count: 8
  1074. [15:22:46][    5.140000] LTQ Crypto Hardware Initialized ..
  1075. [15:22:46][    5.150000] LTQ crypto driver version: 1.2.24
  1076. [15:22:46][    5.150000] usbcore: registered new interface driver usbhid
  1077. [15:22:46][    5.160000] usbhid: USB HID core driver
  1078. [15:22:46][    5.160000] u32 classifier
  1079. [15:22:46][    5.160000]     input device check on
  1080. [15:22:46][    5.170000]     Actions configured
  1081. [15:22:46][    5.170000] nf_conntrack version 0.5.0 (2964 buckets, 11856 max)
  1082. [15:22:46][    5.180000] nf_conntrack_rtsp v0.6.21 loading
  1083. [15:22:46][    5.180000] xt_time: kernel timezone is -0000
  1084. [15:22:46][    5.180000] ipip: IPv4 over IPv4 tunneling driver
  1085. [15:22:46][    5.190000] nf_nat_rtsp v0.6.21 loading
  1086. [15:22:46][    5.190000] ip_tables: (C) 2000-2006 Netfilter Core Team
  1087. [15:22:46][    5.200000] TCP: cubic registered
  1088. [15:22:46][    5.200000] Initializing XFRM netlink socket
  1089. [15:22:46][    5.210000] NET: Registered protocol family 10
  1090. [15:22:46][    5.210000] NET: Registered protocol family 17
  1091. [15:22:46][    5.220000] NET: Registered protocol family 15
  1092. [15:22:46][    5.220000] Bridge firewalling registered
  1093. [15:22:46][    5.220000] Ebtables v2.0 registered
  1094. [15:22:46][    5.230000] lec:lane_module_init: lec.c: initialized
  1095. [15:22:46][    5.230000] mpoa:atm_mpoa_init: mpc.c: initialized
  1096. [15:22:46][    5.240000] KOAM is loaded successfully.
  1097. [15:22:46][    5.240000] l2tp_core: L2TP core driver, V2.0
  1098. [15:22:46][    5.240000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
  1099. [15:22:46][    5.250000] l2tp_netlink: L2TP netlink interface
  1100. [15:22:46][    5.250000] 8021q: 802.1Q VLAN Support v1.8
  1101. [15:22:46][    5.260000] regulator-dummy: disabling
  1102. [15:22:49][    8.420000] UBI: scanning is finished
  1103. [15:22:49][    8.450000] UBI: attached mtd8 (name "system_sw", size 108 MiB) to ubi0
  1104. [15:22:49][    8.450000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
  1105. [15:22:49][    8.460000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
  1106. [15:22:49][    8.470000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
  1107. [15:22:49][    8.470000] UBI: good PEBs: 863, bad PEBs: 1, corrupted PEBs: 0
  1108. [15:22:49][    8.480000] UBI: user volume: 6, internal volumes: 1, max. volumes count: 128
  1109. [15:22:49][    8.490000] UBI: max/mean erase counter: 90/12, WL threshold: 4096, image sequence number: 1777296557
  1110. [15:22:49][    8.500000] UBI: available PEBs: 450, total reserved PEBs: 413, PEBs reserved for bad PEB handling: 19
  1111. [15:22:49][    8.500000] UBI: background thread "ubi_bgt0d" started, PID 590
  1112. [15:22:49][    8.520000] drivers/rtc/hctosys.c: unable to open rtc de[    8.530000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
  1113. [15:22:49][    8.540000] Please append a correct "root=" boot option; here are the available partitions:
  1114. [15:22:49][    8.540000] 1f00            1024 mtdblock0  (driver?)
  1115. [15:22:49][    8.550000] 1f01             256 mtdblock1  (driver?)
  1116. [15:22:49][    8.550000] 1f02             256 mtdblock2  (driver?)
  1117. [15:22:49][    8.560000] 1f03             256 mtdblock3  (driver?)
  1118. [15:22:49][    8.560000] 1f04            1024 mtdblock4  (driver?)
  1119. [15:22:49][    8.570000] 1f05           16384 mtdblock5  (driver?)
  1120. [15:22:49][    8.570000] 1f06             256 mtdblock6  (driver?)
  1121. [15:22:49][    8.580000] 1f07             256 mtdblock7  (driver?)
  1122. [15:22:49][    8.580000] 1f08          110592 mtdblock8  (driver?)
  1123. [15:22:49][    8.590000] 1f09             768 mtdblock9  (driver?)
  1124. [15:22:49][    8.590000] 1f0a            2944 mtdblock10  (driver?)
  1125. [15:22:49][    8.600000] 1f0b           16616 mtdblock11  (driver?)
  1126. [15:22:50][    8.600000] 1f0c            2976 mtdblock12  (driver?)
  1127. [15:22:50][    8.610000] 1f0d            2604 mtdblock13  (driver?)
  1128. [15:22:50][    8.610000] 1f0e            2604 mtdblock14  (driver?)
  1129. [15:22:50][    8.620000] 1f0f           20584 mtdblock15  (driver?)
  1130. [15:22:50][    8.630000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
  1131. [15:22:51][    8.640000] Rebooting in 1 seconds..

复制代码


请千万不要发表任何涉政、涉爆、涉恐、涉军类的内容，只论技术、莫谈政事！(点击见详情) | 恩山无线论坛欢迎您的来访，请互相尊重、友善交流。
回复

使用道具 举报

12下一页
返回列表 发新帖
高级模式
B Color Image Link Quote Code Smilies
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-5-16 10:47

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱：js12377 | @jischina.com.cn 举报电话：025-88802724 本站不良内容举报信箱：68610888@qq.com 举报电话：0519-86695797

快速回复 返回顶部 返回列表