找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 4230|回复: 19

求大哥告知ttl线和接口怎么接

[复制链接]
求大哥告知ttl线和接口怎么接




本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
论坛上好多教程.
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

本帖最后由 11651189 于 2020-2-13 11:53 编辑

2应该是GND,4应该是3.3V。
只须要连接1、2、3,1和3是RX和TX,先乱接,不对再交换1和3。
最好测量一下4和3.3V电源是不是相通的。

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

1 接担任c40的是vcc 3.3 2 +字形接地的是GND 3 4各接一个电阻的细线是tx 或rx , 可以可以交替测试判断  详情 回复 发表于 2020-2-13 15:52
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
11651189 发表于 2020-2-13 11:52
2应该是GND,4应该是3.3V。
只须要连接1、2、3,1和3是RX和TX,先乱接,不对再交换1和3。
最好测量一下4 ...

好的,试试

点评

zhjook说得对,先用电压表测试下再接TTL。看1的走线,应该是电源。我认为方形的触点是电源呢。  发表于 2020-2-13 18:01
你这个错了,别试  详情 回复 发表于 2020-2-13 15:52
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

这应该是WDR7500或者WDR4900
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

本帖最后由 zhjook 于 2020-2-13 15:53 编辑
11651189 发表于 2020-2-13 11:52
2应该是GND,4应该是3.3V。
只须要连接1、2、3,1和3是RX和TX,先乱接,不对再交换1和3。
最好测量一下4 ...

1 接电容c40的是vcc 3.3,供电粗线
2 +字形接地的是GND
3 4各接一个电阻的细线是tx 或rx , 可以可以交替测试判断
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报


你这个错了,别试
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
zhjook 发表于 2020-2-13 15:52
你这个错了,别试

额,还没弄,空了在弄
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

FAST FW450R v1?

教程仅供参考,非针对FW450R
小米路由4 拆机 ttl 刷breed
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
fyi2000 发表于 2020-2-14 23:28
FAST FW450R v1?

教程仅供参考,非针对FW450R

对(^o^),你也有啊!这个路由里面刷的什么瑞小博  认证路由器,
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
fyi2000 发表于 2020-2-14 23:28
FAST FW450R v1?

教程仅供参考,非针对FW450R

还没弄呢,不知道咋个接ttl,怕烧了。。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报


论坛上好多教程
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
今天有空了,连上会丢失连接

▒
▒▒UI▒▒с1.1▒BRչ▒▒▒▒▒3 ▒▒▒҂4:▒MJC▒H▒ap▒▒j▒▒▒▒ion▒.0▒5▒
s▒▒
   ▒▒K▒on▒L     j
                 at▒E▒▒}in▒W+▒▒co▒V▒211J'B▒▒b▒W "▒r1▒Z+▒5
                                                         ta▒▒▒▒▒0▒▒▒▒▒
U▒(lo▒  B▒gh)▒ (▒▒,▒x3▒▒
                        U▒valuY.▒▒0xLX  ▒▒▒a    ▒▒Ea,▒▒▒▒JC▒6j  5
                                                                 F+͡▒Ma▒]J▒ 0▒L "!+͡: ▒j▒x2       "▒▒iceRV▒x1▒C!+͡▒size▒MB ▒▒▒tor▒▒չt =▒4
U▒▒▒de▒X]▒en▒Z▒˫+▒▒
▒▒%%▒▒rn▒끪%%&#9618CRY▒1AN▒S▒ձe ▒
                             ▒foun


                                  j
▒Q.▒   ▒Y▒+▒5 ▒!!▒C▒▒Kse▒ZX▒H▒▒▒i  ▒▒▒▒lrn▒k▒*** '▒
             ▒Y a▒u▒ac_▒▒}▒ni▒ZX+K▒▒▒▒
                                      ▒
                                       ▒▒▒id▒X▒ɕss▒Z
                                                    2▒as▒       ▒▒ing▒▒▒d a▒▒▒s
at▒u▒▒c_e▒▒}▒nitZX+K▒▒ ▒֕▒ ma▒-▒▒22▒j▒Sco򥽹 -▒KK▒▒7 e▒
S2▒▒▒ i▒ZWH(Q!▒S2▒▒▒seW▒▒s▒SH▒ATH▒*▒▒▒s2▒▒▒et ▒˫5
                                                 ATH▒*▒▒0x▒KKҢ00C▒Q▒RS▒▒▒▒ 0▒,▒▒Һ*▒e▒▒*5
        AT▒▒▒▒▒RE▒▒a--▒'j
                         ATȪ*▒▒RE▒�--▒'j&#9618J5ɷ'▒▒▒▒▒0--▒1▒S▒0
ONT▒▒▒0 :▒▒▒j c֖▒▒▒1L▒H▒eth▒ bX',▒2▒▒ce:▒:4LC▒▒K▒I7_▒▒}▒etu▒A▒J▒▒e}
             ath▒.▒Ӆ▒▒_seW▒ATH҅!e▒SPQ▒5EUM0 ▒▒j
                                              at▒.▒▒▒▒▒se▒]▒▒J▒!e}CON▒▒1▒1 ▒▒j
                                                                               ath▒.▒▒▒▒}set]▒AJ▒e}&#9618EõQ▒S LҊ▒j
ONT▒▒▒2 :▒▒▒j                  aK▒I7_▒▒}▒et▒A▒J▒▒e}
             ath▒.▒▒▒▒}set]▒AJ▒▒e}MPEC5QU▒ 2▒▒▒j
                                                atK▒▒7_p▒^5▒tup
                                                               Q!▒_P*▒5▒NTҊ▒3 :1ONT▒▒▒4 :1▒0▒▒ath▒.▒▒▒▒}▒etu▒ATJ▒▒e}MAEC_*UU▒ 4▒▒▒jt]▒AJ▒▒e}
                                                   e▒
                                                     ▒▒
Y
j
  SeW▒▒0▒L▒▒▒29▒▒▒▒0x▒M▒14fC▒▒▒ob▒
                                  ▒▒g ▒
                                       ▒▒▒▒▒nd▒C▒## B▒
                                                      ▒▒g ▒[XV
                                                              с9f0&▒▒▒..▒C!Un▒▒ɕss▒▒▒Y.▒▒ I▒Xց...▒OKC▒HhE▒▒▒ingZ▒ɹel ▒rj

Linux version 2.6.31--LSDK-9.2.0_U6.616 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Thu Jun 6 10:08:19 CST 2013
Ram size passed from bootloader =64M
flash_size passed from bootloader = 4
CPU revision is: 00019750 (MIPS 74Kc)
cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 400 ahb 200
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(ART) mem=32M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 56500k/65536k available (1634k kernel code, 8968k reserved, 403k data, 116k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
Mount-cache hash table entries: 512

****************ALLOC***********************
Packet mem: 8022e3a0 (0x600000 bytes)
********************************************

NET: Registered protocol family 16
ath_pcibios_init: bus 0
***** Warning PCIe 0 H/W not found !!!
registering PCI controller with io_map_base unset
ath_pcibios_init: bus 1
***** Warning PCIe 1 H/W not found !!!
registering PCI controller with io_map_base unset
Reset button pressed.
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 110
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "ART"
->Oops: flash id 0x10215 .
Ooops, why the devices couldn't been initialed?
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
SQUASHFS error: squashfs_read_data failed to read block 0x293834
SQUASHFS error: Unable to read metadata cache entry [293834]
SQUASHFS error: Unable to read inode 0xe8f0164
------------[ cut here ]------------
WARNING: at fs/inode.c:707 unlock_new_inode+0x30/0x58()
Modules linked in:
Call Trace:
[<80197ef8>] dump_stack+0x8/0x34
[<80023af8>] warn_slowpath_common+0x70/0xb0
[<80082804>] unlock_new_inode+0x30/0x58
[<80084960>] iget_failed+0x1c/0x3c
[<800b7864>] squashfs_fill_super+0x620/0x724
[<80071ef4>] get_sb_bdev+0x11c/0x194
[<800b7180>] squashfs_get_sb+0x20/0x2c
[<80070dc4>] vfs_kern_mount+0x68/0xd0
[<80070e90>] do_kern_mount+0x54/0x118
[<8008877c>] do_mount+0x690/0x71c
[<8008889c>] sys_mount+0x94/0x158
[<80200c90>] mount_block_root+0x13c/0x2fc
[<8020108c>] prepare_namespace+0x1c0/0x1f4
[<80200380>] kernel_init+0x114/0x134
[<8000836c>] kernel_thread_helper+0x10/0x18

---[ end trace adcbc5dcd1fb8084 ]---
VFS: Cannot open root device "31:02" or unknown-block(31,2)
Please append a correct "root=" boot option; here are the available partitions:
1f00             128 mtdblock0 (driver?)
1f01            1024 mtdblock1 (driver?)
1f02            2816 mtdblock2 (driver?)
1f03              64 mtdblock3 (driver?)
1f04              64 mtdblock4 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)

我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
Linux版本2.6.31—U6.616的LSDK-9.2.0(root@localhost.localdomain)(gcc版本4.3.3(gcc)-35;2013年6月1日星期四10:08:19 CST

从引导加载程序传递的Ram大小=64M

从引导加载程序传递的闪存大小=4

CPU版本号:00019750(MIPS 74Kc)

cpu apb ddr apb athu系统频率:cpu 720 ddr 400 ahb 200

确定的物理RAM映射:

内存:0400000000@00000000(可用)

设置区域PFN:

正常0x00000000->0x00004000

每个节点的活动区域启动PFN

早期需求图[1]有效PFN范围

0:0x00000000->0x00004000

按分区顺序创建了1个分区列表,并在上进行了移动分组。总页数:16256

内核命令行:console=ttyS0115200 root=31:02 rootfype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(Kernel),2816k(rootfs),64k(config),64k(ART)mem=32M

PID哈希表条目:256(顺序:8124字节)

Dentry缓存哈希表条目:8192(顺序:332768字节)

索引节点缓存哈希表项:4096(顺序:216384字节)

主指令缓存64kB,VIPT,4路,32行字节。

主数据缓存32kB,4路,VIPT,缓存别名,行大小32字节

正在写入ErrCtl registry=000000

Readback ErrCtl寄存器=00000000

内存:56500k/65536k可用(1634k内核代码,8968k保留,403k数据,116k初始化,0k高内存)

IRQ编号:128

支付时间初始化:支付时间初始化完成

正在校准延迟循环。。。359.42波哥米普斯(lpj=718848)

装载缓存哈希表项:512



*****************************************

数据包内存:8022e3a0(0x600000字节)

********************************************



NET:注册协议系列16

Atu pcibios初始化:总线0

*****警告:找不到PCIe 0 H/W!!!

在io映射库未设置的情况下注册PCI控制器

Atu pcibios初始化:总线1

*****警告:找不到PCIe 1 H/W!!!

在io映射库未设置的情况下注册PCI控制器

按下复位按钮。

bio:在0创建slab<bio-0>

NET:注册协议系列2

IP路由缓存哈希表项:1024(顺序:0,4096字节)

TCP建立的哈希表项:2048(顺序:216384字节)

TCP绑定哈希表项:2048(顺序:18192字节)

TCP:已配置哈希表(已建立2048绑定2048)

Net注册的TCP

NET:注册协议系列1

ATH GPIOC专业0

squashfs:4.0版(2009/01/31)Phillip Lougher

msgmni设置为110

o调度程序noop已注册

已注册io计划程序截止日期(默认)

串行:8250/16550驱动程序,1个端口,禁用IRQ共享

串行8250.0:MMIO 0xb8020000处的ttyS0(irq=19)是16550A

控制台[ttyS0]已启用

PPP通用驱动程序版本2.4.2

NET:注册协议系列24

在MTD设备ath-nor0上找到5个cmdlinepart分区

在“ath-nor0”上创建5个MTD分区:

0x000000000000-0x0000020000“u型船”

0x000000020000-0x000012000:“内核”

0x000000120000-0x00003e0000:“rootfs”

0x0000003e0000-0x00003f0000:“配置”

0x00003f0000-0x000040000:“艺术”

->Oops:flash id 0x10215。

哦,为什么这些设备不能被初始化?

注册立方TCP

NET:注册协议系列17

802.1Q VLAN支持v1.8 Ben Greear<greearb@candelatech.com>

David S.Miller添加的所有错误<davem@redhat.com>

athwdt/init:注册WDT成功

Open init:注册OTP成功

SQUASHFS错误:SQUASHFS'u read'数据无法读取块0x293834

SQUASHFS错误:无法读取缓存项元数据[293834]

SQUASHFS错误:无法读取索引节点0xe8f0164

----------[剪到这里]--------------

警告:在fs/inode.c:707解锁新inode+0x30/0x58()

链接的模块:

呼叫跟踪:

[<80197ef8>]转储-u堆栈+0x8/0x34

[<80023af8>]警告slowpath common+0x70/0xb0

[<80082804>]解锁新轭inode+0x30/0x58

[<80084960>]igu失败+0x1c/0x3c

[<800b7864>]squashfs填充super+0x620/0x724

[<80071ef4>]获取bdev+0x11c/0x194

[<800b7180>]squashfs获得u sb+0x20/0x2c

[<80070dc4>]vfs u核心安装+0x68/0xd0

[<80070e90>]至堆芯支座+0x54/0x118

[<8008877c>]安装+0x690/0x71c

[<8008889c>]系统安装+0x94/0x158

[<80200c90>]安装块根+0x13c/0x2fc

[<8020108c>]准备命名空间+0x1c0/0x1f4

[<80200380>]内核初始化+0x114/0x134

[<8000836c>]内核线程助手+0x10/0x18



-[结束跟踪adcbc5dc1fb8084]---

VFS:无法打开根设备“31:02”或未知块(31,2)

请附加正确的“root=”引导选项;以下是可用分区:

1f00 128 mtdblock0(驱动器?)

1f01 1024 mtdblock1(驱动器?)

1f02 2816 mtdblock2(驱动器?)

1f03 64 mtdblock3(驱动程序?)

1f04 64 mtdblock4(驱动器?)

内核死机-未同步:VFS:无法在未知块(31,2)上装载根fs
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
上夹子,用编程器能救回来吗?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-28 06:09

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表