CISCO AP1231G求助~~~~~~~

xt***

我新搞到一台CISCO AP1231G,但是遇到问题,特向坛内大侠求助!
接通电源后LED灯的显示:
1.下面两个灯闪绿色
2.然后第一个灯为虎珀色,第二个灯为绿色
3.三个灯全为绿色
4.第二个灯闪绿色,第三个灯(AP)闪红色,闪耀方式为:红+停+红+红+停,循环下去
正确使用复位键复位后也还是如此.
使用控制台线能通,显示为:

Xmodem file system is available.
flashfs[0]: 5 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1863680
flashfs[0]: Bytes available: 5877760
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from flash parameter block...done.
Base ethernet MAC Address: 00:23:5e:13:76:30
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
link auto-negotiating....
auto-negotiation takes 10000 milli-seconds to complete
ERROR: timeout waiting for auto-negotiation to complete
ERROR: fail to bring ethernet link up

The system has been encountered an error initializing
ethernet port. You may need to check hardware
The system is ignoring the error and continuing boot.
If you interrupt the system boot process, the following
commands will reinitialize ethernet, tftp, and finish
loading the operating system software:

    ether_init
    tftp_init
    boot

Loading "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx"...###########################
################################################################################
##############################################################

File "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x3000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEA
SE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:41 by alnguyen
Image text-base: 0x00003000, data-base: 0x00359FC0

Initializing flashfs...

flashfs[1]: 5 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 1863680
flashfs[1]: Bytes available: 5877760
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-AP1231G-A-K9     (PowerPC405GP) processor (revision A0) with 15038K/13
36K bytes of memory.
Processor board ID FCW1309Y00V
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address:  00:23:5e:13:76:30
Part Number                          : 73-8704-14
PCA Assembly Number                  : 800-23211-14
PCA Revision Number                  : A0
PCB Serial Number                    : FOC13041UL4
Top Assembly Part Number             : 800-29026-02
Top Assembly Serial Number           : FCW1309Y00V
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1231G-A-K9



Press RETURN to get started!


*Mar  1 00:00:04.513: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEA
SE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:41 by alnguyen
*Mar  1 00:00:05.445: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
up
*Mar  1 00:00:06.445: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0, changed state to down
*Mar  1 00:00:23.524: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
此时按Ctrl+break后显示:AP0023.5e13.7630>
请教:此时应该怎么办?(按了?后就不知道该如何办了)
怎样才能使它发出无线信号?

conk***

系统坏了吧，可以寄到恩山店里修的。自己要弄的话，买console线，然后看文档，喜欢折腾的就自己弄。

ra***

以前给公司安装过，第一次使用，和RESET 后，都是先用console。 通过超级终端进入，先给设备配置IP。
有IP后，再通过WEB登录设置。

xt***

怎样设置IP?

知鱼***

ray_c 发表于 2009-10-15 16:33
以前给公司安装过，第一次使用，和RESET 后，都是先用console。 通过超级终端进入，先给设备配置IP。
有IP ...

请问有详细的教程吗？

dang***

你这个是廋ap的ios，要无线控制器才能用，如果要单独用的话，要先改成胖ap才行。

guy***

去官网找相关型号的胖AP固件，可能没有权限下载，把文件名复制去百度搜就可以了。