1900DHP flashing failed, CFE has entered, flash command timed out, log attached, is it a CFE verification firmware problem?

testios

Cause 2014.1.0 ddwrt nxt upgrade 2017.12 ddwrt nxt 1.5.5
Because root changed the name of /lib and started into a problem, the system could not find the cat command, proc command, and the dynamic library was renamed by me.

History ddwrt nxt 1.0 mtd0--mtd5 all backup + programmer firmware
NXT 1.5.5 mtd0 --mtdxx all backup + no backup programmer firmware

Status: Disassembled, TTL link normal, router IP 192.168.11.1 , computer IP , 192.168.11.2 computer ping 192.168.11.1 request timed out.

Route ping 192.168.11.2:

CFE> ping 192.168.11.2
192.168.11.2 (192.168.11.2) is not responding (seq=0)
192.168.11.2 (192.168.11.2): 1 packets sent, 0 received
*** command status = 1

CFE> ping 192.168.11.1
192.168.11.1 (192.168.11.1) is not responding (seq=0)
192.168.11.1 (192.168.11.1): 1 packets sent, 0 received
*** command status = 1



CFE>  flash -noheader 192.168.11.2:firmware.ram nflash1.trx
Reading 192.168.11.2:firmware.ram: Failed.: Timeout occured
*** command status = -21

system timeout,

Looked,bcm subclass of Feixun K3,It's a problem with cfe.,Friends downgrade cfe to get it.,I only have to remove the programmer on the chip.。


TFPD logs:
Connection received from 192.168.11.1 on port 2447 [29/05 06:12:54.419]
Read request for file <firmware.ram>. Mode octet [29/05 06:12:54.419]
Using local port 58132 [29/05 06:12:54.419]
Connection received from 192.168.11.1 on port 2447 [29/05 06:12:59.475]
Read request for file <firmware.ram>. Mode octet [29/05 06:12:59.475]
Using local port 58133 [29/05 06:12:59.475]
Connection received from 192.168.11.1 on port 2447 [29/05 06:13:04.575]
Read request for file <firmware.ram>. Mode octet [29/05 06:13:04.576]
Using local port 58134 [29/05 06:13:04.576]
TIMEOUT waiting for Ack block #1  [29/05 06:13:09.424]
TIMEOUT waiting for Ack block #1  [29/05 06:13:14.480]
TIMEOUT waiting for Ack block #1  [29/05 06:13:19.581]






CFE comes with its own commands
CFE> help
Available commands:

watchdog            Set watchdog value.
nvram               NVRAM utility.
reboot              Reboot.
test ether          Do an ethernet test, reading packets from the net
phyreg              Do an phy register test, read/write register
mii                 Do an mii register test, read/write register
et                  Broadcom Ethernet utility.
clearmem            Clear memory.
memtest             Test memory.
f                   Fill contents of memory.
e                   Modify contents of memory.
d                   Dump memory.
u                   Disassemble instructions.
flash               Update a flash memory device
batch               Load a batch file into memory and execute it
go                  Verify and boot OS image.
boot                Load an executable file into memory and execute it
load                Load an executable file into memory without executing it
save                Save a region of memory to a remote file via TFTP
ping                Ping a remote IP host.
arp                 Display or modify the ARP Table
ifconfig            Configure the Ethernet interface
show clocks         Show current values of the clocks.
show flash          Display information about a flash device.
show heap           Display information about CFE's heap
show memory         Display the system physical memory map.
show devices        Display information about the installed devices.
help                Obtain help for CFE commands

For more information about a command, enter 'help command-name'
*** command status = 0

testios

CFE> go
================================================================================
tmpr  current 70 (273)
tmpr  normal_thresh=98   bootable_thresh=115
current 71 < thresh 116,  booting FW...
================================================================================
FW-A / FW-B header are different
Checking recover image
check_trx: start nflash1.trx_recover
Invalid boot block on disk
check_trx: exit nflash1.trx_recover
Invalid recover image, try normal image...
Checking normal image
check_trx: start nflash1.trx
check_trx: exit nflash1.trx
Checking recover image
check_trx: start nflash1.trx_recover
Invalid boot block on disk
check_trx: exit nflash1.trx_recover
Invalid recover image, try normal image...
Loader:raw Filesys:raw Dev:nflash0.os File: Optionsnull)
Loading: .. 5115512 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.25 (nxtbuild@voip) (gcc version 5.4.0 (LEDE GCC 5.4.0 r2045) ) #0 SMP Sat Dec 16 12:29:08 2017
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Buffalo WXR-1900DHP
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Hit pending asynchronous external abort (FSR=0x00001c06) during first unmask, this is most likely caused by a firmware/bootloader bug.
[    0.000000] PERCPU: Embedded 11 pages/cpu @c6bcd000 s12928 r8192 d23936 u45056
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130816
[    0.000000] Kernel command line: console=ttyS0,115200
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 514584K/524288K available (3378K kernel code, 110K rwdata, 1268K rodata, 224K init, 286K bss, 9704K reserved, 0K cma-reserved, 393216K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0491e44   (4648 kB)
[    0.000000]       .init : 0xc0492000 - 0xc04ca000   ( 224 kB)
[    0.000000]       .data : 0xc04ca000 - 0xc04e58c8   ( 111 kB)
[    0.000000]        .bss : 0xc04e58c8 - 0xc052d178   ( 287 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x0a530000
[    0.000000] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[    0.000000] L2C-310 ID prefetch enabled, offset 1 lines
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB
[    0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x7e530001
[    0.000012] sched_clock: 64 bits at 500MHz, resolution 2ns, wraps every 4398046511103ns
[    0.000030] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xe6a171a037, max_idle_ns: 881590485102 ns
[    0.000213] Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896)
[    0.060111] pid_max: default: 32768 minimum: 301
[    0.060184] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060193] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060635] CPU: Testing write buffer coherency: ok
[    0.060866] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.060938] Setting up static identity map for 0x82a0 - 0x82d4
[    0.120139] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.120207] Brought up 2 CPUs
[    0.120224] SMP: Total of 2 processors activated (3981.31 BogoMIPS).
[    0.120233] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x13)
[    0.120238] CPU: This may indicate a broken bootloader or firmware.
[    0.122342] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.122437] pinctrl core: initialized pinctrl subsystem
[    0.123010] NET: Registered protocol family 16
[    0.123606] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.152106] clocksource: Switched to clocksource arm_global_timer
[    0.152971] NET: Registered protocol family 2
[    0.153483] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.153506] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.153527] TCP: Hash tables configured (established 1024 bind 1024)
[    0.153583] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.153611] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.153780] NET: Registered protocol family 1
[    0.155056] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.155219] Crashlog allocated RAM at address 0x3f00000
[    0.155246] Initialise system trusted keyring
[    0.160283] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.160312] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.161801] Key type asymmetric registered
[    0.161820] Asymmetric key parser 'x509' registered
[    0.161889] bounce: pool size: 64 pages
[    0.161903] io scheduler noop registered
[    0.161915] io scheduler deadline registered (default)
[    0.162352] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.164345] console [ttyS0] disabled
[    0.164401] 18000300.serial: ttyS0 at MMIO 0x18000300 (irq = 18, base_baud = 7812500) is a 16550
[    0.624726] console [ttyS0] enabled
[    0.629298] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[    0.635694] nand: Macronix NAND 128MiB 3,3V 8-bit
[    0.640422] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    0.648029] iproc_nand 18028000.nand: detected 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-8
[    0.657988] Scanning device for bad blocks
[    1.273489] 2 ofpart partitions found on MTD device brcmnand.0
[    1.279338] Creating 2 MTD partitions on "brcmnand.0":
[    1.284509] 0x000000000000-0x000008000000 : "firmware"
[    1.290963] 0x000000400000-0x000008000000 : "ubi"
[    1.297221] libphy: Fixed MDIO Bus: probed
[    1.301440] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[    1.307306] bcma: bus0: Found chip with id 53010, rev 0x00 and package 0x00
[    1.314357] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0)
[    1.323038] bcma: bus0: Core 1 found: Chipcommon B (manuf 0x4BF, id 0x50B, rev 0x01, class 0x0)
[    1.331878] bcma: bus0: Core 2 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, class 0x0)
[    1.339919] bcma: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[    1.348416] bcma: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id  0x82D, rev 0x05, class 0x0)
[    1.356902] bcma: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[    1.365391] bcma: bus0: Core 6 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[    1.373861] bcma: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[    1.382514] bcma: bus0: Core 8 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[    1.391159] bcma: bus0: Core 9 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[    1.399823] bcma: bus0: Core 10 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x01, class 0x0)
[    1.409942] bcma: bus0: Core 11 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x01, class 0x0)
[    1.418409] bcma: bus0: Core 12 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x01, class 0x0)
[    1.426898] bcma: bus0: Core 13 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0)
[    1.435218] bcma: bus0: Core 14 found: I2S (manuf 0x4BF, id 0x834, rev 0x03, class 0x0)
[    1.443356] bcma: bus0: Core 15 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0)
[    1.452801] bcma: bus0: Core 16 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0)
[    1.463648] bcma: bus0: Core 17 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0)
[    1.471788] bcma: bus0: Core 18 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0)
[    1.481485] bcma: bus0: Core 19 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
[    1.491015] bcma: bus0: Flash type not supported
[    1.496862] m25p80 spi32766.0: mx25l4005a (512 Kbytes)
[    1.502092] 2 ofpart partitions found on MTD device spi32766.0
[    1.507941] Creating 2 MTD partitions on "spi32766.0":
[    1.513110] 0x000000000000-0x000000060000 : "boot"
[    1.518643] 0x000000070000-0x000000080000 : "nvram"
[    1.537254] bgmac_bcma bcma0:3: Found PHY addr: 30 (NOREGS)
[    1.542878] bgmac_bcma bcma0:3: Support for Roboswitch not implemented
[    1.551316] b53_common: found switch: BCM53012, rev 5
[    1.556394] b53: link UP on port 0
[    1.559826] b53: link UP on port 5
[    1.563920] bgmac_bcma bcma0:4: Found PHY addr: 0
[    1.568647] bgmac_bcma bcma0:4: Support for Roboswitch not implemented
[    1.575282] bgmac_bcma bcma0:4: Invalid MAC addr: 00:00:00:00:00:00
[    1.581599] bgmac_bcma bcma0:4: Using random MAC: fa:db:d4:c4:84:46
[    1.589099] bgmac_bcma bcma0:5: Found PHY addr: 0
[    1.593866] bgmac_bcma bcma0:5: Support for Roboswitch not implemented
[    1.600512] bgmac_bcma bcma0:5: Invalid MAC addr: 00:00:00:00:00:00
[    1.606811] bgmac_bcma bcma0:5: Using random MAC: 6e:f3:35:28:6d:15
[    1.614299] bgmac_bcma bcma0:6: Unsupported core_unit 3
[    1.619569] bgmac_bcma: probe of bcma0:6 failed with error -524
[    1.730216] pcie_iproc_bcma bcma0:7: PCI host bridge to bus 0000:00
[    1.736515] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff]
[    1.743439] pcie_iproc_bcma bcma0:7: link: UP
[    1.748055] PCI: bus0: Fast back to back transfers disabled
[    1.753668] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.762102] PCI: bus1: Fast back to back transfers disabled
[    1.767741] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
[    1.774570] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
[    1.781919] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.786900] pci 0000:00:00.0:   bridge window [mem 0x08000000-0x080fffff]
[    1.900206] pcie_iproc_bcma bcma0:8: PCI host bridge to bus 0001:00
[    1.906502] pci_bus 0001:00: root bus resource [mem 0x40000000-0x47ffffff]
[    1.913417] pcie_iproc_bcma bcma0:8: link: UP
[    1.917999] PCI: bus0: Fast back to back transfers disabled
[    1.923606] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.932042] PCI: bus1: Fast back to back transfers disabled
[    1.937685] pci 0001:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
[    1.944515] pci 0001:01:00.0: BAR 0: assigned [mem 0x40000000-0x40007fff 64bit]
[    1.951864] pci 0001:00:00.0: PCI bridge to [bus 01]
[    1.956846] pci 0001:00:00.0:   bridge window [mem 0x40000000-0x400fffff]
[    2.070207] pcie_iproc_bcma bcma0:9: PCI host bridge to bus 0002:00
[    2.076501] pci_bus 0002:00: root bus resource [mem 0x48000000-0x4fffffff]
[    2.083409] pcie_iproc_bcma bcma0:9: PHY or data link is INACTIVE!
[    2.089603] pcie_iproc_bcma bcma0:9: no PCIe EP device detected
[    2.095609] pcie_iproc_bcma bcma0:9: PCIe controller setup failed
[    2.102817] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[    2.111849] bcma: bus0: Bus registered
[    2.116537] NET: Registered protocol family 10
[    2.122050] NET: Registered protocol family 17
[    2.126558] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.139232] 8021q: 802.1Q VLAN Support v1.8
[    2.143523] Registering SWP/SWPB emulation handler
[    2.148703] Loading compiled-in X.509 certificates
[    2.154344] Loaded X.509 cert 'Kernel Build Key: 3c987b77d34af1e015092ee16360c6a0bdb5188f'
[    2.164151] UBI: auto-attach mtd1
[    2.167307] ubi0: attaching mtd1
[    2.175284] random: nonblocking pool is initialized
[    2.831441] ubi0: scanning is finished
[    2.844572] ubi0: attached mtd1 (name "ubi", size 124 MiB)
[    2.850081] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.857003] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.863817] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.870801] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0
[    2.876819] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    2.884069] mubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 2975385861
[    2.893232] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20
[    2.902514] ubi0: background thread "ubi_bgt0d" started, PID 330
[    2.909563] block ubiblock0_0: created from ubi0:0(rootfs)
[    2.915104] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    2.926140] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    2.933570] Freeing unused kernel memory: 224K (c0492000 - c04ca000)
[    3.413632] init: Console is alive
[    3.417179] init: - watchdog -
[    4.152199] usbcore: registered new interface driver usbfs
[    4.157795] usbcore: registered new interface driver hub
[    4.163205] usbcore: registered new device driver usb
[    4.191381] Found region: US
[    4.200531] SCSI subsystem initialized
[    4.209404] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.217505] ehci-platform: EHCI generic platform driver
[    4.224949] ehci-platform 18021000.ehci: EHCI Host Controller
[    4.226410] bcm_ns_usb3 18105000.usb3-phy: Registered Broadcom Northstar USB 3.0 PHY driver
[    4.228790] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.230314] ohci-platform: OHCI generic platform driver
[    4.230482] ohci-platform 18022000.ohci: Generic Platform OHCI controller
[    4.230506] ohci-platform 18022000.ohci: new USB bus registered, assigned bus number 1
[    4.230625] ohci-platform 18022000.ohci: irq 29, io mem 0x18022000
[    4.271555] ehci-platform 18021000.ehci: new USB bus registered, assigned bus number 2
[    4.279630] ehci-platform 18021000.ehci: irq 29, io mem 0x18021000
[    4.294804] hub 1-0:1.0: USB hub found
[    4.298652] hub 1-0:1.0: 2 ports detected
[    4.311062] xhci-hcd 18023000.xhci: xHCI Host Controller
[    4.312349] ehci-platform 18021000.ehci: USB 2.0 started, EHCI 1.00
[    4.312918] hub 2-0:1.0: USB hub found
[    4.312955] hub 2-0:1.0: 2 ports detected
[    4.330511] xhci-hcd 18023000.xhci: new USB bus registered, assigned bus number 3
[    4.338271] xhci-hcd 18023000.xhci: hcc params 0x02501164 hci version 0x100 quirks 0x01010010
[    4.346876] xhci-hcd 18023000.xhci: irq 30, io mem 0x18023000
[    4.353309] hub 3-0:1.0: USB hub found
[    4.357114] hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
[    4.364488] xhci-hcd 18023000.xhci: xHCI Host Controller
[    4.369829] xhci-hcd 18023000.xhci: new USB bus registered, assigned bus number 4
[    4.390189] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.398854] hub 4-0:1.0: USB hub found
[    4.402748] hub 4-0:1.0: 1 port detected
[    4.412839] usbcore: registered new interface driver usb-storage
[    4.422477] init: - preinit -
[    5.790214] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.796163] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.540146] bgmac_bcma bcma0:3 eth0: Link is Up - 1Gbps/Full - flow control off
[    7.547502] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.554022] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[    7.972104] mount_root: loading kmods from internal overlay
[    8.101662] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 515
[    8.143707] UBIFS (ubi0:1): recovery needed
[    8.251593] UBIFS (ubi0:1): recovery completed
[    8.256130] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    8.264001] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    8.273947] UBIFS (ubi0:1): FS size: 115675136 bytes (110 MiB, 911 LEBs), journal size 5840896 bytes (5 MiB, 46 LEBs)
[    8.284587] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[    8.291223] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID B8BBF118-ED55-4B93-B90B-B24F6535C910, small LPT model
[    8.303812] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[    8.317488] block: extroot: not configured
[    8.350251] UBIFS (ubi0:1): un-mount UBI device 0
[    8.354985] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[    8.364476] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 518
[    8.456365] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[    8.464247] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    8.474197] UBIFS (ubi0:1): FS size: 115675136 bytes (110 MiB, 911 LEBs), journal size 5840896 bytes (5 MiB, 46 LEBs)
[    8.484837] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[    8.491469] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID B8BBF118-ED55-4B93-B90B-B24F6535C910, small LPT model
[    8.582862] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[    8.595786] block: extroot: not configured
[    8.621967] mount_root: switching to ubifs overlay
[    8.632014] urandom-seed: Seeding with /etc/urandom.seed
/etc/preinit: line 1: cat: not found
/etc/preinit: line 1: uci: not found
/etc/preinit: line 1: grep: not found

sgalv

Is it brushed?

testios

Brush it up

afeng11

testios was posted on 2020-5-6 23:21
Brush it up

CFE file sharing one, thanks