TTL刷breed 没有成功,求教

aiy***

breed-mt7620-reset1.binTTL 刷H大的 breed 失败
log 如下,求指点 :

EBG3200E

U-Boot 1.1.3 (Dec 29 2014 - 11:44:49)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.2.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: 16 MBytes NOR Flash
Dateec 29 2014  Time:11:44:49
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
raspi_read: from:50010 len:40
raspi_read: from:720010 len:40

=================================================
Check image validation:
Image1 Header Magic Number --> Failed
Image2 Header Magic Number --> OK
Image2 Header Checksum --> OK
Image2 Data Checksum --> raspi_read: from:720050 len:ebc83
OK
Image1 Stable Flag --> Stable
Image1 Try Counter --> 0
Image2 Stable Flag --> Stable
Image2 Try Counter --> 0

Image1: Broken Image2: OK root_zone: 1

=================================================

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
4
You choosed 2

0
raspi_read: from:40028 len:6


2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.1.1) ==:192.168.1.1
        Input server IP (192.168.1.2) ==:192.168.1.2
        Input Linux Kernel filename (EBG3200E_r7998.bin) ==:1.bin            

netboot_common, argc= 3

NetTxPacket = 0x83FE56C0

KSEG1ADDR(NetTxPacket) = 0xA3FE56C0

NetLoop,call eth_halt !

NetLoop,call eth_init !
Trying Eth0 (10/100-M)

Waitting for RX_DMA_BUSY status Start... done


ETH_STATE_ACTIVE!!
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename '1.bin'.

TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (00:e0:6f:02:9e:f0)
Got it
##################
done
Bytes transferred = 91481 (16559 hex)
NetBootFileXferSize= 00016559
raspi_erase_write: offs:50000, count:16559
raspi_erase: offs:50000 len:10000
.
raspi_write: to:50000 len:10000
.
raspi_read: from:50000 len:10000
raspi_read: from:60000 len:10000
raspi_erase: offs:60000 len:10000
.
raspi_write: to:60000 len:10000
.
raspi_read: from:60000 len:10000
Done!
## Error: environment overflow, "Image1Stable" deleted
## Error: environment overflow, "Image1Try" deleted
## Error: environment overflow, "root_zone" deleted
## Booting image at bc720000 ...
## Error: environment overflow, "Image2Try" deleted
raspi_read: from:30000 len:10000
Erasing SPI Flash...
raspi_erase: offs:30000 len:10000
.
Writing to SPI Flash...
raspi_write: to:30000 len:10000
.
done
raspi_read: from:720010 len:40
   Image Name:   MIPS OpenWrt Linux-2.6.32.27
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    965763 Bytes = 943.1 kB
   Load Address: 88000000
   Entry Point:  88000000
raspi_read: from:720050 len:ebc83
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 88000000) ...