RT3050 USB 驱动应该安装哪些？

ccpoint

今天编译了个固件，希望能直接支持DIR-600的 USB 编译时选择了
kmod-usb-core
kmod-usb-rt305x-dwc_otg
kmod-usb-storage
kmod-usb-storage-extras
还有其他一些组件

但是USB设备好像完全没有识别到 后来装了 Kmod-usb ohci uhci usb2什么的试了试 出了一堆错误 ，还是不能识别到USB设备 具体说应该安装哪些？

请不要胡乱输入以及粘贴、复制等方式灌水

请尊重作者、并共同维护网站的正常阅读，否则账户将会被限制发帖、回帖，并且积分可能会被清零，站内短信以及阅读权限等都会受到影响，谢谢。 具体限制方式：https://www.right.com.cn/forum/thread-8307840-1-1.html

ccpoint

2L贴上些信息

root@OpenWrt:/# dmesg
Linux version 2.6.39.4 (user@debian) (gcc version 4.5.4 20110808 (pre
inaro GCC 4.5-2011.08) ) #1 Thu Oct 27 04:29:43 EDT 2011
prom: fw_arg0=00000001, fw_arg1=01f5bfb0, fw_arg2=01f5c3b0, fw_arg3=0
env[0]: memsize=32
env[1]: initrd_start=0x00000000
env[2]: initrd_size=0x0
env[3]: flash_start=0xBF000000
env[4]: flash_size=0x400000
env[0]: memsize=32
env[1]: initrd_start=0x00000000
env[2]: initrd_size=0x0
env[3]: flash_start=0xBF000000
env[4]: flash_size=0x400000
bootconsole [early0] enabled
CPU revision is: 0001964c (MIPS 24Kc)
Ralink RT3052   id:1 rev:2 running at 320.00 MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
On node 0 totalpages: 8192
free_area_init_node: node 0, pgdat 8021b000, node_mem_map 81000000
  Normal zone: 64 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8128 pages, LIFO batch:0
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on.  Total pages:
Kernel command line:  board=DIR-600-B1 mtdparts=physmap-flash.0:192k(
4k(devdata)ro,64k(devconf)ro,832k(kernel),2944k(rootfs),3776k@0x50000
console=ttyS1,57600 rootfstype=squashfs,jffs2
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 30032k/32768k available (1844k kernel code, 2736k reserved, 3
52k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=
NR_IRQS:48
console [ttyS1] enabled, bootconsole disabled
Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is D-Link DIR-600 B1
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c
Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
physmap platform flash device: 00800000 at bf000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufactu
00c2 Chip ID 0x0022a8
physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.1.
number of CFI chips: 1
6 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 6 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "devdata"
0x000000040000-0x000000050000 : "devconf"
0x000000050000-0x000000120000 : "kernel"
0x000000120000-0x000000400000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=340000, len=C
0x000000340000-0x000000400000 : "rootfs_data"
0x000000050000-0x000000400000 : "firmware"
ramips_eth: loaded
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 152k freed
Button Hotplug driver version 0.4.1
Registered led device: d-link:amber:status
Registered led device: d-link:green:status
Registered led device: d-link:blue:wps
JFFS2 notice: (305) jffs2_build_xattr_subsystem: complete building xa
em, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orph
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
dwc_otg: version 2.72a 24-JUN-2008
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Compat-wireless backport release: compat-wireless-2011-09-28-6-g8163a
Backport based on wireless-testing.git master-2011-10-05
cfg80211: Calling CRDA to update world regulatory domain
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.1) entering forwarding state
br-lan: port 1(eth0.1) entering forwarding state
br-lan: received packet on eth0.1 with own address as source address
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain,
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: rt2800pci-phy0::radio
Registered led device: rt2800pci-phy0::assoc
Registered led device: rt2800pci-phy0::quality
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (471 buckets, 1884 max)
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
ramips-wdt: timeout value 60 must be 0 < timeout < 40
br-lan: received packet on eth0.1 with own address as source address
br-lan: received packet on eth0.1 with own address as source address
br-lan: received packet on eth0.1 with own address as source address
br-lan: received packet on eth0.1 with own address as source address
br-lan: received packet on eth0.1 with own address as source address

99010

要在编译前把内核的USB模块加上

ccpoint

要在编译前把内核的USB模块加上
99010 发表于 2011-10-27 17:44

加上哪些呢 FLASH快满了，，

99010

加上哪些呢 FLASH快满了，，
ccpoint 发表于 2011-10-27 17:46

请参考mach-hw550-3g.c

ccpoint

请参考mach-hw550-3g.c
99010 发表于 2011-10-27 18:41

多谢指导 USB已经有反应了 ·

xiaoqiang

楼主你有DIR600B支持USB的UBOOT么
有的话发份给我吧