|
|
信翼r102,cpu是mt7628nn，接ttl无法启动路由，通电后再接ttl能输出信息，但是输出的信息从头到尾没有输入的地方，求助，是不是没进uboot？直接进系统了？设备看灯闪的情况，不插ttl能进去uboot模式，但是获取不到ip，设置192.168.1.1也不行，不知道是不是没有uboot，ttl信息如下，求助大佬帮分析一下，想刷openwrt
[ 0.000000] Linux version 3.10.14 (dimmalex@x51hyper) (gcc version 4.8.3 (Ope nWrt/Linaro GCC 4.8-2014.04 unknown) ) #2 Fri Nov 15 16:54:12 CST 2019
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 575 MHz
[ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256
[ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 ro otfstype=squashfs,jffs2 print-fatal-signals=1
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0006651f
[ 0.000000] Readback ErrCtl register=0006651f
[ 0.000000] Memory: 61140k/65536k available (2898k kernel code, 4396k reserve d, 464k data, 220k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Kernel hard watchdog refresh early
[ 0.000000] console [ttyS1] enabled
[ 0.100000] Calibrating delay loop... 382.46 BogoMIPS (lpj=764928)
[ 0.132000] pid_max: default: 32768 minimum: 301
[ 0.136000] Mount-cache hash table entries: 512
[ 0.140000] NET: Registered protocol family 16
[ 0.144000] RALINK_GPIOMODE = 55054405
[ 0.148000] RALINK_GPIOMODE = 55044405
[ 0.248000] ***** Xtal 25MHz *****
[ 0.252000] start PCIe register access
[ 0.752000] RALINK_RSTCTRL = 2400000
[ 0.756000] RALINK_CLKCFG1 = fdbfffc0
[ 0.760000]
[ 0.760000] *************** MT7628 PCIe RC mode *************
[ 1.260000] PCIE0 no card, disable it(RST&CLK)
[ 1.276000] bio: create slab <bio-0> at 0
[ 1.280000] usbcore: registered new interface driver usbfs
[ 1.284000] usbcore: registered new interface driver hub
[ 1.288000] usbcore: registered new device driver usb
[ 1.292000] Switching to clocksource MIPS
[ 1.296000] NET: Registered protocol family 2
[ 1.308000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 1.320000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 1.332000] TCP: Hash tables configured (established 512 bind 512)
[ 1.344000] TCP: reno registered
[ 1.352000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.364000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.376000] NET: Registered protocol family 1
[ 1.384000] RPC: Registered named UNIX socket transport module.
[ 1.396000] RPC: Registered udp transport module.
[ 1.408000] RPC: Registered tcp transport module.
[ 1.416000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.428000] MTK/Ralink EHCI/OHCI init.
[ 1.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.452000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.464000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIOR ITY) (c) 2001-2006 Red Hat, Inc.
[ 1.484000] msgmni has been set to 119
[ 1.492000] io scheduler noop registered (default)
[ 1.508000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.524000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
[ 1.536000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 1.552000] Ralink gpio driver initialized for r103(b0000060=55044411)
[ 1.564000] Ralink gpio driver initialized for r103(b0000064=1)
[ 1.576000] flash manufacture id: ef, device id 40 17
[ 1.584000] W25Q64BV(ef 40170000) (8192 Kbytes)
[ 1.596000] mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x0001000 0 (64K) .numeraseregions = 0
[ 1.616000] Creating 6 MTD partitions on "raspi":
[ 1.624000] 0x000000000000-0x000000780000 : "ALL"
[ 1.636000] 0x000000000000-0x000000030000 : "Bootloader"
[ 1.648000] 0x000000030000-0x000000040000 : "Config"
[ 1.656000] 0x000000040000-0x000000050000 : "Factory"
[ 1.668000] 0x000000050000-0x000000780000 : "firmware"
[ 1.680000] 0x000000177b51-0x000000780000 : "rootfs"
[ 1.692000] mtd: partition "rootfs" must either start or end on erase block b oundary or be smaller than an erase block -- forcing read-only
[ 1.716000] mtd: partition "rootfs_data" created automatically, ofs=0x550000, len=0x230000
[ 1.732000] 0x000000550000-0x000000780000 : "rootfs_data"
[ 1.748000] 0x000000780000-0x000000800000 : "Fconfig"
[ 1.756000] GMAC1_MAC_ADRH -- : 0x00004cbc
[ 1.768000] GMAC1_MAC_ADRL -- : 0x98061cee
[ 1.776000] Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descr iptors allocated, mtu = 1500!
[ 1.792000] GMAC1_MAC_ADRH -- : 0x00004cbc
[ 1.800000] GMAC1_MAC_ADRL -- : 0x98061cee
[ 1.812000] PROC INIT OK!
[ 1.816000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.828000] ehci-pci: EHCI PCI platform driver
[ 1.836000] ehci-platform: EHCI generic platform driver
[ 1.868000] ******MT7628 mtk phy
[ 1.876000] *****run project phy.
[ 1.888000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 1.904000] FM_OUT value: u4FmOut = 127(0x0000007F)
[ 1.912000] FM detection done! loop = 1
[ 1.928000] SR calibration value u1SrCalVal = 6
[ 1.936000] *********Execute mt7628_phy_init!!
[ 1.944000] ehci-platform ehci-platform: EHCI Host Controller
[ 1.956000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 1.972000] ehci-platform ehci-platform: irq 18, io mem 0x101c0000
[ 1.996000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 2.008000] hub 1-0:1.0: USB hub found
[ 2.016000] hub 1-0:1.0: 1 port detected
[ 2.024000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.056000] *********Execute mt7628_phy_init!!
[ 2.064000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[ 2.076000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 2.092000] ohci-platform ohci-platform: irq 18, io mem 0x101c1000
[ 2.164000] hub 2-0:1.0: USB hub found
[ 2.172000] hub 2-0:1.0: 1 port detected
[ 2.180000] gre: GRE over IPv4 demultiplexor driver
[ 2.188000] ip_gre: GRE over IPv4 tunneling driver
[ 2.200000] TCP: cubic registered
[ 2.208000] NET: Registered protocol family 10
[ 2.220000] NET: Registered protocol family 17
[ 2.228000] 8021q: 802.1Q VLAN Support v1.8
[ 2.236000] registered taskstats version 1
[ 2.248000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.264000] Freeing unused kernel memory: 220K (80349000 - 80380000)
procd: Console is alive
[ 3.008000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 3.596000]
[ 3.596000]
[ 3.596000] Unsupported Device!
[ 3.596000] Vendor=19d2 ProdID=579
[ 3.596000] Manufacturer=ZXIC,Incorporated Product=ZXIC Mobile Boardband
[ 3.596000]
[ 4.264000] SCSI subsystem initialized
[ 4.276000] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.296000] usbcore: registered new interface driver usb-storage
procd: - preinit -
procd: - early -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 6.216000] l2tp_core: L2TP core driver, V2.0
[ 6.228000] l2tp_netlink: L2TP netlink interface
[ 6.276000] u32 classifier
[ 6.280000] input device check on
[ 6.288000] Actions configured
[ 6.372000] Mirror/redirect action on
[ 6.388000] Failed to load ipt action
[ 6.416000] usbcore: registered new interface driver cdc_acm
[ 6.428000] cdc_acm: USB Abstract Control Model driver for USB modems and ISD N adapters
[ 6.460000] usbcore: registered new interface driver cdc_wdm
[ 6.484000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 6.492000] Type=Linux
[ 6.528000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
[ 6.564000] nf_conntrack_rtsp v0.6.21 loading
[ 6.616000] nf_nat_rtsp v0.6.21 loading
[ 6.640000] Ralink APSoC Hardware Watchdog Timer
[ 6.660000] rdm_major = 253
[ 6.672000] usbcore: registered new interface driver ums-alauda
[ 6.688000] usbcore: registered new interface driver ums-cypress
[ 6.700000] usbcore: registered new interface driver ums-datafab
[ 6.716000] usbcore: registered new interface driver ums-freecom
[ 6.732000] usbcore: registered new interface driver ums-isd200
[ 6.744000] usbcore: registered new interface driver ums-jumpshot
[ 6.760000] usbcore: registered new interface driver ums-karma
[ 6.772000] usbcore: registered new interface driver ums-sddr09
[ 6.788000] usbcore: registered new interface driver ums-sddr55
[ 6.804000] usbcore: registered new interface driver ums-usbat
[ 6.824000] usbcore: registered new interface driver usbserial
[ 6.836000] usbcore: registered new interface driver usbserial_generic
[ 6.852000] usbserial: USB Serial support registered for generic
[ 6.908000] xt_time: kernel timezone is -0000
[ 6.928000] cdc_ether 1-1:1.0 eth1: register 'cdc_ether' at usb-ehci-platform -1, CDC Ethernet Device, 00:a0:c6:00:00:00
[ 6.960000] usbcore: registered new interface driver cdc_ether
[ 6.984000] usbcore: registered new interface driver cdc_ncm
[ 7.024000] PPP generic driver version 2.4.2
[ 7.036000] PPP MPPE Compression module registered
[ 7.048000] NET: Registered protocol family 24
[ 7.060000] usbcore: registered new interface driver qmi_wwan
[ 7.076000] usbcore: registered new interface driver rndis_host
[ 7.096000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 7.112000] usbcore: registered new interface driver option
[ 7.124000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 7.136000] option 1-1:1.2: GSM modem (1-port) converter detected
[ 7.156000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 7.168000] option 1-1:1.3: GSM modem (1-port) converter detected
[ 7.188000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 7.200000] option 1-1:1.4: GSM modem (1-port) converter detected
[ 7.228000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 7.240000] option 1-1:1.5: GSM modem (1-port) converter detected
[ 7.264000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3
[ 10.332000] jffs2: notice: (729) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 12.556000] 4C:FFFFFFBC:FFFFFF98: 6:1C:FFFFFFEE
[ 12.568000] Raeth v3.1 (Tasklet,SkbRecycle)
[ 12.576000]
[ 12.576000] phy_tx_ring = 0x03334000, tx_ring = 0xa3334000
[ 12.588000]
[ 12.588000] phy_rx_ring0 = 0x03336000, rx_ring[0] = 0xa3336000
[ 12.604000]
[ 12.604000] phy_rx_ring0 = 0x03336000, rx_ring[0] = 0xa3336000
[ 12.620000] WAN at the P4
[ 12.624000] RESET MT7628 PHY!
[ 12.944000] GMAC1_MAC_ADRH -- : 0x00004cbc
[ 12.952000] GMAC1_MAC_ADRL -- : 0x98061cee
[ 12.960000] RT305x_ESW: Link Status Changed
[ 14.208000] device eth0 entered promiscuous mode
[ 14.216000] lan: port 1(eth0) entered forwarding state
[ 14.228000] lan: port 1(eth0) entered forwarding state
[ 14.328000] lan: port 1(eth0) entered forwarding state
[ 14.956000] dhcp service king mode
[ 15.396000]
[ 15.396000]
[ 15.396000] === pAd = c091d000, size = 1345120 ===
[ 15.396000]
[ 15.416000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
[ 15.428000] <-- RTMPAllocAdapterBlock, Status=0
[ 15.440000] RtmpChipOpsHook(492): Not support for HIF_MT yet!
[ 15.448000] mt7628_init()-->
[ 15.456000] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
[ 15.464000] e2.bin mt7628_init(1117)::(2), pChipCap->fw_len(63056)
[ 15.480000] mt_bcn_buf_init(218): Not support for HIF_MT yet!
[ 15.488000] <--mt7628_init()
[ 15.544000] TX_BCN DESC a2409000 size = 320
[ 15.552000] RX[0] DESC a240b000 size = 2048
[ 15.564000] RX[1] DESC a240e000 size = 1024
[ 15.584000] cfg_mode=9
[ 15.588000] cfg_mode=9
[ 15.592000] wmode_band_equal(): Band Equal!
[ 15.604000] APSDCapable[0]=1
[ 15.608000] APSDCapable[1]=1
[ 15.616000] APSDCapable[2]=1
[ 15.620000] APSDCapable[3]=1
[ 15.628000] APSDCapable[4]=1
[ 15.632000] APSDCapable[5]=1
[ 15.640000] APSDCapable[6]=1
[ 15.644000] APSDCapable[7]=1
[ 15.648000] APSDCapable[8]=1
[ 15.656000] APSDCapable[9]=1
[ 15.660000] APSDCapable[10]=1
[ 15.668000] APSDCapable[11]=1
[ 15.672000] APSDCapable[12]=1
[ 15.680000] APSDCapable[13]=1
[ 15.684000] APSDCapable[14]=1
[ 15.692000] APSDCapable[15]=1
[ 15.696000] default ApCliAPSDCapable[0]=1
[ 15.704000] default ApCliAPSDCapable[1]=1
[ 15.784000] RT305x_ESW: Link Status Changed
[ 15.920000] Key1Str is Invalid key length(11) or Type(0)
[ 15.948000] RTMPSetDefaultChannel() : default channel to 1
[ 15.956000] load fw image from fw_header_image
[ 15.968000] AndesMTLoadFwMethod1(2174)::pChipCap->fw_len(63056)
[ 15.980000] FW Version:_e2_mp
[ 15.984000] FW Build Date:20150211175503
[ 15.992000] CmdAddressLenReq:(ret = 0)
[ 16.000000] CmdFwStartReq: override = 1, address = 1048576
[ 16.012000] CmdStartDLRsp: WiFI FW Download Success
[ 16.108000] usbserial: USB Serial deregistering driver GSM modem (1-port)
[ 16.124000] option1 ttyUSB3: GSM modem (1-port) converter now disconnected fr om ttyUSB3
[ 16.152000] option1 ttyUSB2: GSM modem (1-port) converter now disconnected fr om ttyUSB2
[ 16.180000] option1 ttyUSB1: GSM modem (1-port) converter now disconnected fr om ttyUSB1
[ 16.204000] option1 ttyUSB0: GSM modem (1-port) converter now disconnected fr om ttyUSB0
[ 16.224000] usbcore: deregistering interface driver option
[ 16.240000] option 1-1:1.5: device disconnected
[ 16.252000] option 1-1:1.4: device disconnected
[ 16.260000] MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
[ 16.272000] efuse_probe: efuse = 10000012
[ 16.280000] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=4
[ 16.292000] RtmpEepromGetDefault::e2p_dafault=2
[ 16.300000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P defaul t = 2
[ 16.316000] NVM is FLASH mode
[ 16.320000] 1. Phy Mode = 14
[ 16.340000] option 1-1:1.3: device disconnected
[ 16.352000] option 1-1:1.2: device disconnected
[ 16.400000] usbserial: USB Serial deregistering driver generic
[ 16.412000] usbcore: deregistering interface driver usbserial_generic
[ 16.428000] usbcore: deregistering interface driver usbserial
[ 16.452000] usbcore: deregistering interface driver rndis_host
[ 16.476000] usbcore: deregistering interface driver cdc_ether
[ 16.488000] cdc_ether 1-1:1.0 eth1: unregister 'cdc_ether' usb-ehci-platform- 1, CDC Ethernet Device
[ 16.504000] Country Region from e2p = ffff
[ 16.512000] tssi_1_target_pwr_g_band = 28
[ 16.520000] 2. Phy Mode = 14
[ 16.528000] 3. Phy Mode = 14
[ 16.532000] NICInitPwrPinCfg(11): Not support for HIF_MT yet!
[ 16.544000] NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF _MT yet!
[ 16.560000] mt_mac_init()-->
[ 16.564000] MtAsicInitMac()-->
[ 16.572000] mt7628_init_mac_cr()-->
[ 16.580000] MtAsicSetMacMaxLen(1241): Set the Max RxPktLen=1024!
[ 16.592000] <--mt_mac_init()
[ 16.596000] WTBL Segment 1 info:
[ 16.604000] MemBaseAddr/FID:0x28000/0
[ 16.612000] EntrySize/Cnt:32/128
[ 16.616000] WTBL Segment 2 info:
[ 16.624000] MemBaseAddr/FID:0x40000/0
[ 16.632000] EntrySize/Cnt:64/128
[ 16.636000] WTBL Segment 3 info:
[ 16.644000] MemBaseAddr/FID:0x42000/64
[ 16.652000] EntrySize/Cnt:64/128
[ 16.660000] WTBL Segment 4 info:
[ 16.664000] MemBaseAddr/FID:0x44000/128
[ 16.672000] EntrySize/Cnt:32/128
[ 16.680000] AntCfgInit(2876): Not support for HIF_MT yet!
[ 16.692000] MCS Set = ff ff 00 00 01
[ 16.700000] MtAsicSetChBusyStat(826): Not support for HIF_MT yet!
[ 16.892000] CmdSlotTimeSet:(ret = 0)
[ 19.416000] SYNC - BBP R4 to 20MHz.l
[ 19.732000] SYNC - BBP R4 to 20MHz.l
[ 20.048000] SYNC - BBP R4 to 20MHz.l
[ 20.364000] SYNC - BBP R4 to 20MHz.l
[ 20.680000] SYNC - BBP R4 to 20MHz.l
[ 20.996000] SYNC - BBP R4 to 20MHz.l
[ 21.308000] SYNC - BBP R4 to 20MHz.l
[ 21.620000] SYNC - BBP R4 to 20MHz.l
[ 21.936000] SYNC - BBP R4 to 20MHz.l
[ 22.248000] SYNC - BBP R4 to 20MHz.l
[ 22.492000] Turn off early pat watchdog refush
[ 22.500000] Started WatchDog Timer.
[ 22.568000] MtAsicSetRalinkBurstMode(2919): Not support for HIF_MT yet!
[ 22.580000] MtAsicSetPiggyBack(763): Not support for HIF_MT yet!
[ 22.616000] MtAsicSetTxPreamble(2898): Not support for HIF_MT yet!
[ 22.632000] MtAsicAddSharedKeyEntry(1308): Not support for HIF_MT yet!
[ 22.648000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
[ 22.660000] Main bssid = 4c:bc:98:06:1c:e8
[ 22.668000] <==== rt28xx_init, Status=0
[ 22.680000] mt7628_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f
[ 22.696000] WiFi Startup Cost (ra0): 7.152s
[ 22.984000] cdc_ether 1-1:1.0 eth1: register 'cdc_ether' at usb-ehci-platform -1, CDC Ethernet Device, 00:a0:c6:00:00:00
[ 23.040000] usbcore: registered new interface driver cdc_ether
[ 23.120000] usbcore: registered new interface driver usbserial
[ 23.136000] usbcore: registered new interface driver usbserial_generic
[ 23.160000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
[ 23.172000] MtAsicSetPiggyBack(763): Not support for HIF_MT yet!
[ 23.184000] usbserial: USB Serial support registered for generic
[ 23.196000] MtAsicSetRalinkBurstMode(2919): Not support for HIF_MT yet!
[ 23.208000] MtAsicSetPiggyBack(763): Not support for HIF_MT yet!
[ 23.244000] usbcore: registered new interface driver option
[ 23.256000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 23.272000] option 1-1:1.2: GSM modem (1-port) converter detected
[ 23.284000] MtAsicSetTxPreamble(2898): Not support for HIF_MT yet!
[ 23.300000] MtAsicAddSharedKeyEntry(1308): Not support for HIF_MT yet!
[ 23.312000] AddTxSType: already registered TxSType (PID = 32, Format = 0
[ 23.328000] AddTxSType: already registered TxSType (PID = 6, Format = 0
[ 23.340000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
[ 23.352000] Main bssid = 4c:bc:98:06:1c:e8
[ 23.380000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 23.392000] option 1-1:1.3: GSM modem (1-port) converter detected
[ 23.624000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[ 23.636000] option 1-1:1.4: GSM modem (1-port) converter detected
[ 23.660000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[ 23.672000] option 1-1:1.5: GSM modem (1-port) converter detected
[ 23.712000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3
[ 23.752000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0
[ 23.764000] MtAsicSetPiggyBack(763): Not support for HIF_MT yet!
[ 23.776000] MtAsicSetRalinkBurstMode(2919): Not support for HIF_MT yet!
[ 23.792000] MtAsicSetPiggyBack(763): Not support for HIF_MT yet!
[ 23.828000] MtAsicSetTxPreamble(2898): Not support for HIF_MT yet!
[ 23.844000] MtAsicAddSharedKeyEntry(1308): Not support for HIF_MT yet!
[ 23.860000] AddTxSType: already registered TxSType (PID = 32, Format = 0
[ 23.872000] AddTxSType: already registered TxSType (PID = 6, Format = 0
[ 23.884000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
[ 23.896000] Main bssid = 4c:bc:98:06:1c:e8
[ 23.976000] device ra0 entered promiscuous mode
[ 23.988000] lan: port 2(ra0) entered forwarding state
[ 23.996000] lan: port 2(ra0) entered forwarding state
[ 24.096000] lan: port 2(ra0) entered forwarding state
[ 24.248000] traffic monitor at misp mode(l)
procd: - init complete -
[ 38.360000] dhcp service king mode
[ 38.920000] dhcp service king mode
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？立即注册
×
|
/1 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
