HG320刷DD不能启动 附上TTL启动信息

过期的可乐

HG320，电信原本的系统。买回来后，先刷了dd-wrt.v24-18000_NEWD-2_K2.6_mini.bin系统，在这个系统下，刷了sady大侠的CFE，后刷了Netcore(NR235W)CN-V1.2(beta5)，再刷了TT。
每次刷之前和刷之后，在minniweb界面下都有清除NVRAM


现在的问题：
Netcore的固件和TT的固件可以来回自由的刷，刷后可以正常启动
但是，Netcore系统或者TT系统，在minmiweb界面下，刷了DD后，都无法正常启动。刷之前和刷之后，都在minniweb界面下都有清除过NVRAM，也在TTL中断过CFE，在CFE下也执行过清除NVRAM的命令。刷完DD后，浏览器（遨游浏览器的地址栏有DDwrt的logo)192.168.1.1无法打开 ，google的浏览器也一样。ping 192.168.1.1 -t一直显示time out。修复过网卡连接，没有用。
已经尝试过下面的三个DD版本：
dd-wrt.v24-18000_NEWD-2_K2.6_mini.bin （电信原本系统时成功刷过一次，后再刷无法启动）

ftp://www.dd-wrt.com/others/eko/ ... EWD-2_K2.6_mega.bin ftp://www.dd-wrt.com/others/eko/ ... EWD-2_K2.6_mini.bin

请大家指点一下！

过期的可乐

顶一下！

过期的可乐

请大家指点一下

ttlove

dd-wrt.v24-18688_NEWD-2_K2.6_mega.bin
我现在刷着这个版本，能正常使用的。

过期的可乐

贴上刷DD后TTL的启动信息

1. CFE version 5.60.120.9  based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
   
2. Build Date: 2011骞05鏈04鏃鏄熸湡涓15:32:36 CST (root@localhost.localdomain)
   
3. Copyright (C) 2000-2008 Broadcom Corporation.
   
4. 
   
5. Init Arena
   
6. Init Devs.
   
7. Boot partition size = 131072(0x20000)
   
8. Found a 16MB ST compatible serial flash
   
9. [CFE][boot][ST Serial flash offset 00000000 size 128KB]
   
10. [CFE][trx][ST Serial flash offset 00020000 size 1KB]
    
11. [CFE][os][ST Serial flash offset 0002001C size 16224KB]
    
12. [CFE][nvram][ST Serial flash offset 00FF8000 size 32KB]
    
13. [CFE][boot][ST Serial flash offset 00000000 size 128KB]
    
14. [CFE][trx0][ST Serial flash offset 00020000 size 1KB]
    
15. [CFE][os0][ST Serial flash offset 0002001C size 8832KB]
    
16. [CFE][trx1][ST Serial flash offset 008C0000 size 1KB]
    
17. [CFE][os1][ST Serial flash offset 008C001C size 7392KB]
    
18. [CFE][nvram][ST Serial flash offset 00FF8000 size 32KB]
    
19. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.120.9
    
20. CPU type 0x19749: 500MHz
    
21. Tot mem: 65536 KBytes
    
22. 
    
23. CFE mem:    0x80700000 - 0x8079A7D0 (632784)
    
24. Data:       0x807306D0 - 0x80733850 (12672)
    
25. BSS:        0x80733850 - 0x807347D0 (3968)
    
26. Heap:       0x807347D0 - 0x807987D0 (409600)
    
27. Stack:      0x807987D0 - 0x8079A7D0 (8192)
    
28. Text:       0x80700000 - 0x807306C8 (198344)
    
29. 
    
30. Device eth0:  hwaddr 00-90-4C-21-60-01, ipaddr 192.168.1.1, mask 255.255.255.0
    
31.         gateway not set, nameserver not set
    
32. cur=
    
33. buf=go;
    
34. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
    
35. Loading: Failed.
    
36. Could not load :: Timeout occured
    
37. Boot from big image !!
    
38. Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
    
39. Loading: .. 3916 bytes read
    
40. Entry at 0x80001000
    
41. Closing network.
    
42. Starting program at 0x80001000
    
43. Linux version 2.6.24.111 (root@dd-wrt) (gcc version 4.1.2) #9413 Thu Mar 8 01:57:25 CET 2012
    
44. CPU revision is: 00019749
    
45. Found a 16MB ST compatible serial flash
    
46. Determined physical RAM map:
    
47. memory: 04000000 @ 00000000 (usable)
    
48. Zone PFN ranges:
    
49.   Normal          0 ->    16384
    
50.   HighMem     16384 ->    16384
    
51. Movable zone start PFN for each node
    
52. early_node_map[1] active PFN ranges
    
53.     0:        0 ->    16384
    
54. Built 1 zonelists in Zone order.  Total pages: 16384
    
55. Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd
    
56. Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
    
57. Primary data cache 32kB, 4-way, linesize 32 bytes.
    
58. Synthesized TLB refill handler (20 instructions).
    
59. Synthesized TLB load handler fastpath (32 instructions).
    
60. Synthesized TLB store handler fastpath (32 instructions).
    
61. Synthesized TLB modify handler fastpath (31 instructions).
    
62. PID hash table entries: 512 (order: 9, 2048 bytes)
    
63. CPU: BCM5357 rev 1 at 500 MHz
    
64. Using 250.000 MHz high precision timer.
    
65. console [ttyS0] enabled
    
66. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    
67. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    
68. Memory: 58660k/65536k available (3522k kernel code, 6820k reserved, 1373k data, 188k init, 0k highmem)
    
69. Mount-cache hash table entries: 512
    
70. NET: Registered protocol family 16
    
71. Generic PHY: Registered new driver
    
72. PCI: no core
    
73. PCI: no core
    
74. PCI: Fixing up bus 0
    
75. NET: Registered protocol family 2
    
76. Time: MIPS clocksource has been installed.
    
77. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    
78. TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    
79. TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
    
80. TCP: Hash tables configured (established 2048 bind 2048)
    
81. TCP reno registered
    
82. devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
    
83. devfs: boot_options: 0x1
    
84. squashfs: version 3.0 (2006/03/15) Phillip Lougher
    
85. io scheduler noop registered
    
86. io scheduler deadline registered (default)
    
87. HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
    
88. N_HDLC line discipline registered.
    
89. Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    
90. serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
    
91. PPP generic driver version 2.4.2
    
92. PPP Deflate Compression module registered
    
93. PPP BSD Compression module registered
    
94. MPPE/MPPC encryption/compression module registered
    
95. NET: Registered protocol family 24
    
96. PPPoL2TP kernel driver, V1.0
    
97. tun: Universal TUN/TAP device driver, 1.6
    
98. tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    
99. et_module_init: passivemode set to 0x0
    
100. eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.9
     
101. pflash: found no supported devices
     
102. bootloader size: 131072
     
103. nvram size: 32768
     
104. sflash: Filesystem type: squashfs, size=0x613a10
     
105. partition size = 6428672
     
106. Creating 5 MTD partitions on "sflash":
     
107. 0x00000000-0x00020000 : "cfe"
     
108. 0x00020000-0x00ff0000 : "linux"
     
109. 0x0017e800-0x007a0000 : "rootfs"
     
110. mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
     
111. 0x00ff0000-0x01000000 : "nvram"
     
112. 0x007a0000-0x00ff0000 : "ddwrt"
     
113. Broadcom Watchdog Timer: 0.07 initialized.
     
114. u32 classifier
     
115.     Actions configured
     
116. Netfilter messages via NETLINK v0.30.
     
117. nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
     
118. ctnetlink v0.93: registering with nfnetlink.
     
119. IPv4 over IPv4 tunneling driver
     
120. GRE over IPv4 tunneling driver
     
121. ip_tables: (C) 2000-2006 Netfilter Core Team
     
122. ClusterIP Version 0.8 loaded successfully
     
123. TCP bic registered
     
124. TCP cubic registered
     
125. TCP westwood registered
     
126. TCP highspeed registered
     
127. TCP hybla registered
     
128. TCP htcp registered
     
129. TCP vegas registered
     
130. TCP scalable registered
     
131. NET: Registered protocol family 1
     
132. NET: Registered protocol family 17
     
133. Welcome to PF_RING 3.2.1
     
134. (C) 2004-06 L.Deri <deri@ntop.org>
     
135. NET: Registered protocol family 27
     
136. PF_RING: bucket length    128 bytes
     
137. PF_RING: ring slots       4096
     
138. PF_RING: sample rate      1 [1=no sampling]
     
139. PF_RING: capture TX       No [RX only]
     
140. PF_RING: transparent mode Yes
     
141. PF_RING initialized correctly.
     
142. PF_RING: registered /proc/net/pf_ring/
     
143. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
     
144. All bugs added by David S. Miller <davem@redhat.com>
     
145. decode 1f02
     
146. VFS: Mounted root (squashfs filesystem) readonly.
     
147. Mounted devfs on /dev
     
148. Freeing unused kernel memory: 188k freed
     
149. start service
     
150. starting Architecture code for broadcom
     
151. done
     
152. Booting device: Linksys WRT54G/GL/GS
     
153. roboswitch: Probing device eth0: found a 5325!
     
154. Segmentation fault
     

复制代码

过期的可乐

继续

1. [USB] checking...
   
2. /etc/preinit: line 66: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
   
3. /etc/preinit: line 66: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
   
4. eth1: Operation not supported
   
5. wl0.1: No such device
   
6. wl0.2: No such device
   
7. wl0.3: No such device
   
8. eth1: Operation not permitted
   
9. nbw = 20
   
10. 800, 300, 6
    
11. spec 2B06
    
12. eth1: Invalid argument
    
13. eth1: Invalid argument
    
14. eth1: Operation not supported
    
15. eth1: Operation not supported
    
16. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
    
17. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
    
18. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
    
19. br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
    
20. device br0 entered promiscuous mode
    
21. br0: No such file or directory
    
22. device vlan0 entered promiscuous mode
    
23. device eth0 entered promiscuous mode
    
24. br0: No such file or directory
    
25. eth1: Operation not supported
    
26. wl0.1: No such device
    
27. wl0.2: No such device
    
28. wl0.3: No such device
    
29. eth1: Operation not permitted
    
30. eth1: Invalid argument
    
31. nbw = 20
    
32. 800, 300, 6
    
33. spec 2B06
    
34. eth1: Invalid argument
    
35. eth1: Invalid argument
    
36. eth1: Operation not supported
    
37. eth1: Operation not supported
    
38. device eth1 entered promiscuous mode
    
39. br0: port 2(eth1) entering learning state
    
40. br0: port 1(vlan0) entering learning state
    
41. device br0 left promiscuous mode
    
42. device br0 entered promiscuous mode
    
43. device br0 left promiscuous mode
    
44. device br0 entered promiscuous mode
    
45. br0: topology change detected, propagating
    
46. br0: port 2(eth1) entering forwarding state
    
47. br0: topology change detected, propagating
    
48. br0: port 1(vlan0) entering forwarding state
    
49. device vlan1 entered promiscuous mode
    
50. device vlan1 left promiscuous mode
    
51. The Milkfish Router Services
    
52. ERROR: Necessary service setting not found: milkfish_username - aborting.
    
53. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
    
54. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
    
55. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
    
56. The Milkfish Router Services
    
57. Restoring SIP ddsubscriber database from NVRAM...
    
58. Empty.
    
59. The Milkfish Router Services
    
60. Restoring SIP ddaliases database from NVRAM...
    
61. Empty.
    
62. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
    
63. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
    
64. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
    
65. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
    
66. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
    
67. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
    
68. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
    
69. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
    
70. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
    
71. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
    
72. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
    
73. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
    
74. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
    
75. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
    
76. /bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
    
77. vlan1: No such process
    
78. vlan1: No such process
    
79. device vlan0 left promiscuous mode
    
80. br0: port 1(vlan0) entering disabled state
    
81. device eth1 left promiscuous mode
    
82. br0: port 2(eth1) entering disabled state
    
83. bridge br0 is still up; can't delete it

复制代码

wuxianfun

刷dd要原版cfe

wangkaifu2010

顶起，怎么才能刷回原版的CFE?

e1649152

死循环了

e1649152

openwrt下可以刷CFE吗？

e1649152

解决办法在这里。。。https://www.right.com.cn/forum/thread-101722-1-7.html

真悲剧