删除

lts***

无参考意义删除

Q***

我的qca9880没问题

wuli***

两个网卡换一下位置就知道了

hello***

你机器硬件有冇问题？我可以帮你编译一份固件，你试试看啊,
你加我qq917970230再聊聊，

我的是qca9887 5G一切都正常，

1. [    0.130698] MIPS: machine is TP-LINK TL-WDR5600 v3
   
2. [    0.572977] registering PCI controller with io_map_base unset
   
3. [    0.589003] PCI host bridge to bus 0000:00
   
4. [    0.593719] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
   
5. [    0.601517] pci_bus 0000:00: root bus resource [io  0x0001]
   
6. [    0.607849] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
   
7. [    0.615549] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
   
8. [    0.624589] pci 0000:00:00.0: [168c:0050] type 00 class 0x028000
   
9. [    0.624621] pci 0000:00:00.0: invalid calibration data
   
10. [    0.630474] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
    
11. [    0.630531] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
    
12. [    0.630597] pci 0000:00:00.0: supports D1
    
13. [    0.630612] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
    
14. [    0.630841] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
    
15. [    0.630879] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
    
16. [    0.639225] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
    
17. [    0.647429] pci 0000:00:00.0: using irq 40 for pin 1

复制代码

1. [   10.695015] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
   
2. [   10.701027] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
   
3. [   11.528836] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
   
4. [   11.539950] ath10k_pci 0000:00:00.0: Falling back to user helper
   
5. [   11.680982] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
   
6. [   11.691655] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9887/hw1.0/firmware-6.bin failed with error -2
   
7. [   11.702761] ath10k_pci 0000:00:00.0: Falling back to user helper
   
8. [   11.843797] firmware ath10k!QCA9887!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed
   
9. [   11.858437] ath10k_pci 0000:00:00.0: qca9887 hw1.0 target 0x4100016d chip_id 0x004000ff sub 0000:0000
   
10. [   11.868005] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
    
11. [   11.882069] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00045 api 5 features no-p2p,ignore-otp,skip-clock-init,mfp,allows-mesh-bcast crc32 0b419264
    
12. [   11.981839] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9887/hw1.0/board-2.bin failed with error -2
    
13. [   11.992698] ath10k_pci 0000:00:00.0: Falling back to user helper
    
14. [   12.075002] firmware ath10k!QCA9887!hw1.0!board-2.bin: firmware_loading_store: map pages failed
    
15. [   12.084508] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 546cca0d
    
16. [   13.137527] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1

复制代码

Q***

hello_limin 发表于 2019-7-11 19:54
你机器硬件有冇问题？我可以帮你编译一份固件，你试试看啊,
你加我qq917970230再聊聊，

有无过minipcie的qca9984？迟小小想入手

lts***

wulishui 发表于 2019-7-11 19:39
两个网卡换一下位置就知道了

2.4g,5g互换吗

那个***

hello_limin 发表于 2019-7-11 19:54
你机器硬件有冇问题？我可以帮你编译一份固件，你试试看啊,
你加我qq917970230再聊聊，

楼主分享下软路由支持网卡的固件啊   

hello***

那个男人 发表于 2019-12-22 17:49
楼主分享下软路由支持网卡的固件啊

我没搞过软路由，不知道如果搞支持网卡的固件，抱歉了