N1救砖卡在7%怎么解决，有没有大佬知道

yin***

图片就是报错的窗口框，有大佬知道怎么解决吗
已经解决，换了块EMMC搞定了

隐形***

截图截全+换固件。

C***

7%的话，你继续强刷，有的运气好能刷好，卡7的原因是磁盘也就是emmc不识别，要么拆下emmc写数据，要么换一片emmc。或者参考我的帖子，或者卖给我

lanj***

企鹅3126848027

yin***

Cmy 发表于 2023-2-7 12:53
7%的话，你继续强刷，有的运气好能刷好，卡7的原因是磁盘也就是emmc不识别，要么拆下emmc写数据，要么换一 ...

我就是换了一块，扩容了

yin***

隐形的肩膀 发表于 2023-2-7 12:47
截图截全+换固件。

更新了，固件换那个

C***

yinghua 发表于 2023-2-7 13:07
我就是换了一块，扩容了

可以试试重新装拆emmc，会不会是虚焊

yin***

Cmy 发表于 2023-2-7 13:23
可以试试重新装拆emmc，会不会是虚焊

是我今天用u 盘启动的op ，用终端刷入op 到emmc ，好像刷报错了就这样了

yin***

Cmy 发表于 2023-2-7 13:23
可以试试重新装拆emmc，会不会是虚焊

我等下再去吹一下加固一下

隐形***

擦除两个选项去掉试过了没

yin***

隐形的肩膀 发表于 2023-2-7 20:00
擦除两个选项去掉试过了没

试过了
GXL:BL1:9ac50e:bb16dc;FEAT:BDFC31BC:0OC:3;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 236973

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 4
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
aml log : R2048 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
aml log : R2048 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
aml log : R2048 check pass!
Load bl33 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00053400
aml log : R2048 check pass!
NOTICE:  BL3-1: v1.0(release):a625749
NOTICE:  BL3-1: Built : 11:25:15, Aug 25 2017
[BL31]: GXL CPU setup!
NOTICE:  BL31: BL33 decompress pass
mpu_config_enablek
[Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
OPS=0x04
2 de 15 ab 4a c7 11 73 5b 4 c 96 [0.844224 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01-00010-gfe36fb9 (Mar 02 2018 - 19:00:28)

DRAM:  2 GiB
Relocation Offset is: 76ed9000
register usb cfg[0][1] = 0000000077f5d330
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
MMC:   aml_priv->desc_buf = 0x0000000073ed9640
aml_priv->desc_buf = 0x0000000073edb960
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
init_part() 278: PART_TYPE_DOS
[mmc_init] mmc init success
dtb magic 5f6c6c70
aml log: no key found ...
aml log : fail with 1135Decrypt dtb: Sig Check 1135
      Amlogic multi-dtb tool
      Cannot find legal dtb!
get_partition_from_dts: not find /partitions node FDT_ERR_BADMAGIC.
get_ptbl_from_dtb()-259: get partition table from dts faild
mmc_device_init()-1081: get partition table from dtb failed
get_ptbl_rsv()-483: magic faild MPT, ic_regs_handler
ffffffc0098d1918 t intel_soc_pmic_exec_mipi_pmic_seq_element
ffffffc0098d1a64 t int340x_thermal_handler_attach
ffffffc0098d1a74 t iort_register_domain_token
ffffffc0098d1b04 t iort_deregister_domain_token
ffffffc0098d1b88 t iort_find_domain_token
ffffffc0098d1c00 t iort_msi_map_id
ffffffc0098d1d14 t iort_node_map_id
ffffffc0098d1f78 t iort_pmsi_get_dev_id
ffffffc0098d2200 t iort_get_device_domain
ffffffc0098d23b8 t acpi_configure_pmsi_domain
ffffffc0098d256c t iort_iommu_msi_get_resv_regions
ffffffc0098d2738 t iort_iommu_configure_id
ffffffc0098d29d4 t iort_scan_node
ffffffc0098d2b6c t iort_pci_iommu_init
ffffffc0098d2be0 t iort_dma_get_ranges
ffffffc0098d2c94 t iort_iommu_xlate
ffffffc0098d2d74 t iort_delete_fwnode
ffffffc0098d2df8 t acpi_arch_dma_setup
ffffffc0098d2f78 t viot_iommu_configure
ffffffc0098d3078 t viot_pci_dev_iommu_init
ffffffc0098d3168 t pnp_register_protocol
ffffffc0098d327c t pnp_unregister_protocol
ffffffc0098d32e0 t pnp_free_resource
ffffffc0098d331c t pnp_free_resources
ffffffc0098d3384 t pnp_alloc_dev
ffffffc0098d3464 t pnp_release_device
ffffffc0098d34f4 t __pnp_add_device
ffffffc0098d3618 t pnp_add_device
ffffffc0098d3724 t __pnp_remove_device
ffffffc0098d37a8 t pnp_alloc_card
ffffffc0098d38f4 t pnp_add_card
ffffffc0098d3a4c t pnp_release_card
ffffffc0098d3a90 t card_probe
ffffffc0098d3d50 t pnp_remove_card
ffffffc0098d3e3c t pnp_remove_card_device
ffffffc0098d3eac t pnp_add_card_device
ffffffc0098d3f40 t pnp_request_card_device
ffffffc0098d4024 t pnp_release_card_devicebus_hdcp!
"Synchronous Abort" handler, esr 0x96000004
ELR:     77f21be8
LR:      77f21be4
x0 : 0000000000020000 x1 : 0000000000000930
x2 : 0000000077f5f748 x3 : 0000000073ede6d0
x4 : 0000000000000320 x5 : 0000000073edece0
x6 : 0000000000000001 x7 : 0000000073edece0
x8 : 0000000077f5f748 x9 : 0000000000000000
x10: 0000000000000000 x11: 0000000000000000
x12: 0000000000000000 x13: 0000000000000000
x14: 0000000000000000 x15: 0000000000000000
x16: 0000000000000000 x17: 0000000000000000
x18: 0000000073ec8e28 x19: 0000000073edd970
x20: 0000000073ede6e0 x21: 0000000000000000
x22: 0000000077fbb000 x23: 0000000000000000
x24: 00000000fffffffc x25: 0000000077f59000
x26: 0000000073ede6c0 x27: 6f69762074203837
x28: 0000000000000000 x29: 0000000073eb8c10

Resetting CPU ...

resetting ...这是报错代码

yin***

隐形的肩膀 发表于 2023-2-7 20:00
擦除两个选项去掉试过了没

TTL进终端一直报这个，反复循环

隐形***

看起来感觉像是emmc问题。你也可以试试  cfdisk 删除所有分区，然后直接线刷安卓系统。

yin***

EMMC挂了应该，换了一块好了

yin***

隐形的肩膀 发表于 2023-2-8 11:57
看起来感觉像是emmc问题。你也可以试试  cfdisk 删除所有分区，然后直接线刷安卓系统。

今天拆下来找到其他的emmc 换上去救砖好了