本帖最后由 游弋 于 2024-3-9 22:28 编辑
想刷wrt做聚合,结果变砖了。
具体硬件如下 7621at+7612en+7603en nanya 128 16m spi w25q128fvsig LAN/WAN LLLLW
刷了 r3g 的 breed,变砖。
有编程器,直接刷回之前也备份过的固件竟然还是无法正常启动。一直卡在 Starting kernel ...
复位键能进uboot。
抢救中......
中间编程器又尝试刷了 8820v2 和 小米4a 的固件,启动后都是1秒闪一下灯,重启。
没找到合适的wrt固件,也没找到可以用的breed。主要是也不知道刷哪个版本。希望各位路过的大神,指导小弟一下。
下面是ttl输出信息。一直卡 Starting kernel ... 重启
Setup the d228/v520/v520b GPIO
Uboot identify string is mt7621:v520:4.3.4-082621(U-Boot 1.1.3 (Aug 31 2021 - 15:04:29))
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87fa0000
Config XHCI 40M PLL
Winbond crackid get
Read flash crackid: 87511928FF630C65
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Aug 31 2021 Time:15:04:29
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =128 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW
Setup the d228/v520/v520b GPIO
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3 0
mt7621 check the mode
mt7621 get boot upgrade(18) press(262144) 0 time
Upgrade mode read(18:262144:0)
3: System Boot system code via Flash.
## Booting image at bc050000 ...
Image Name: OpenWrt Linux-3.10.14-169495
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1373959 Bytes = 1.3 MB
Load Address: 81001000
Entry Point: 81001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 81001000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
下面是进uboot信息
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
default: 3 0
mt7621 check the mode
mt7621 get boot upgrade(18) press(0) 0 time
mt7621 get boot upgrade(18) press(0) 1 time
mt7621 get boot upgrade(18) press(0) 2 time
mt7621 get boot upgrade(18) press(0) 3 time
mt7621 get boot upgrade(18) press(0) 4 time
mt7621 get boot upgrade(18) press(0) 5 time
mt7621 get boot upgrade(18) press(0) 6 time
mt7621 get boot upgrade(18) press(0) 7 time
mt7621 get boot upgrade(18) press(0) 8 time
mt7621 get boot upgrade(18) press(0) 9 time
mt7621 enter upgrade mode
Upgrade mode read(18:0:1)
Input Linux Kernel filename set all in LAN LLLLL
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 10.10.10.3; our IP address is 10.10.10.123
Filename 'farm.upgrade'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
ArpTimeoutCheck
TFTP from server 10.10.10.3; our IP address is 10.10.10.123
Filename 'farm.upgrade'.
TIMEOUT_COUNT=10,Load address: 0x80100000
|