螃蟹真坑爹 RTL8198C+RTL819X 求固件

zwen***

拿到一个awifi（Edge-core ecw3350）路由，号称是Made in Taiwan的货。
结果拆开上TTL看了下，坑啊！RTL8198C（CPU revision is: 00019a24 (MIPS 1074Kc)）+ RTL819X无线芯片（具体型号不确定）


系统是一个定制的OpenWRT，限制诸多，担心可能有后门，所以想刷过OpenWRT，结果愣是没有找到这个方案的固件！！
唯一看到的是之前 lintel 大神的帖子计划造一个，但没有下文不知道造出来没有。
wikidevi上查到有两款路由器用了ASUS RP-AC68U（RTL8198C）和D-Link DIR-879（RTL8198CS）
请问大家，这货还能愉快的玩耍吗？现在有没有RTL8198C的固件？

以下是TTL信息：
BBoooottiinng.
DRAM Type: DDR2
        DRAM frequency: 390MHz
        DRAM Size = 64  MB
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@
@ chip__no chip__id mfr___id dev___id cap___id size_sft dev_size chipSize
@ 0000000h 0c22017h 00000c2h 0000020h 0000017h 0000000h 0000017h 0800000h
@ blk_size blk__cnt sec_size sec__cnt pageSize page_cnt chip_clk chipName
@ 0010000h 0000080h 0001000h 0000800h 0000100h 0000010h 0000041h MX25L6405D
@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
Jump to image start=0x80500000...


OpenWrt kernel loader for Mips board
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80000000...

[    0.000000] Linux version 3.10.49 (ring@accton-To-be-filled-by-O-E-M) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 SMP Tue Nov 10 10:12:40 CST 2015
[    0.000000] CPU revision is: 00019a24 (MIPS 1074Kc)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] PERCPU: Embedded 7 pages/cpu @81083000 s6656 r8192 d13824 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=AP console=ttyS0,38400 linuxpart=0x60000 hwpart=0x20000
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61020k/65536k available (2889k kernel code, 4516k reserved, 684k data, 200k init, 0k highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] CPU0: status register was 10000400
[    0.000000] CPU0: status register now 10000400
[    0.000000] console [ttyS0] enabled
[    0.260000] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
[    0.340000] pid_max: default: 32768 minimum: 301
[    0.350000] Mount-cache hash table entries: 512
GO[    0.360000] CPU revision is: 00019a24 (MIPS 1074Kc)
[    0.370000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.400000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.500000] Synchronize counters for CPU 1: done.
[    0.520000] Brought up 2 CPUs
[    0.530000] NET: Registered protocol family 16
[    0.540000] INFO: initializing USB devices ...
[    0.740000] UPHY: 8198c ASIC u3 of u3 40M phy patch
[    5.050000] bio: create slab <bio-0> at 0
[    5.060000] SCSI subsystem initialized
[    5.070000] usbcore: registered new interface driver usbfs
[    5.080000] usbcore: registered new interface driver hub
[    5.090000] usbcore: registered new device driver usb
[    5.100000] Switching to clocksource MIPS
[    5.110000] NET: Registered protocol family 2
[    5.120000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    5.150000] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
[    5.170000] TCP: Hash tables configured (established 512 bind 512)
[    5.190000] TCP: reno registered
[    5.200000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    5.220000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    5.240000] NET: Registered protocol family 1
[    5.250000] HW reset pin enabled
[    5.280000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.300000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    5.330000] msgmni has been set to 119
[    5.340000] io scheduler noop registered
[    5.360000] io scheduler deadline registered (default)
[    5.370000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    5.390000] serial8250: ttyS0 at MMIO 0x18002000 (irq = 26) is a 16550A
[    5.420000] SPI INIT
[    5.430000]  ------------------------- Force into Single IO Mode ------------------------
[    5.450000] |No chipID  Sft chipSize blkSize secSize pageSize sdCk opCk      chipName    |
[    5.480000] | 0 c22017h  0h  800000h  10000h   1000h     100h   50    0   MX6405D/05E/45E|
[    5.510000]  ----------------------------------------------------------------------------
[    5.540000] SPI flash(MX6405D/05E/45E) was found at CS0, size 0x800000
[    5.560000] Creating 3 MTD partitions on "flash_bank_1":
[    5.580000] 0x000000000000-0x000000060000 : "boot"
[    5.590000] 0x000000060000-0x0000007f0000 : "linux"
[    5.610000] 0x000000227000-0x0000007f0000 : "rootfs"
[    5.630000] mtd: device 2 (rootfs) set to be root filesystem
[    5.650000] mtd: partition "rootfs_data" created automatically, ofs=0x595000, len=0x25b000
[    5.680000] 0x000000595000-0x0000007f0000 : "rootfs_data"
[    5.700000]
[    5.700000] Probing RTL819X NIC-kenel stack size order[1]...
[    6.380000] eth0 added. vid=9 Member port 0x11e...
[    6.400000] eth1 added. vid=8 Member port 0x101...
[    6.410000] xhci-hcd xhci-hcd: xHCI Host Controller
[    6.430000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1
[    6.450000] xhci-hcd xhci-hcd: irq 42, io mem 0x18040000
[    6.470000] hub 1-0:1.0: USB hub found
[    6.480000] hub 1-0:1.0: 1 port detected
[    6.500000] xhci-hcd xhci-hcd: xHCI Host Controller
[    6.510000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2
[    6.540000] hub 2-0:1.0: USB hub found
[    6.550000] hub 2-0:1.0: 1 port detected
[    6.560000] usbcore: registered new interface driver usb-storage
[    6.580000] -------8196D OTG init
[    6.790000] dwc_otg: version 2.60a 22-NOV-2006
[    6.810000]  [S0] lmdev=83994600
[    6.820000] device_register :register pass
[    6.830000]   [S2]  otg_dev=838e8280
[    7.050000]   [S3] hcd==839b5000
[    7.060000] DWC_otg: Using DMA mode
[    7.070000] dwc_otg logicmodule: DWC OTG Controller
[    7.080000] dwc_otg logicmodule: new USB bus registered, assigned bus number 3
[    7.110000] dwc_otg logicmodule: irq 41, io mem 0xb8030000
[    7.130000] set OTG host to high speed !
[    7.140000] DWC_otg: Init: Port Power? op_state=1
[    7.150000] DWC_otg: Init: Power Port (0)
[    7.170000] hub 3-0:1.0: USB hub found
[    7.180000] hub 3-0:1.0: 1 port detected
[    7.190000]   [S1] dwc_otg_driver, lmdriver=8036d828
[    7.210000] rtl819x-wdt rtl819x-wdt: Initialized
[    7.230000] TCP: westwood registered
[    7.240000] NET: Registered protocol family 17
[    7.260000] Bridge firewalling registered
[    7.270000] 8021q: 802.1Q VLAN Support v1.8
[    7.300000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    7.320000] Freeing unused kernel memory: 200K (8037e000 - 803b0000)
procd: Console is alive
procd: - watchdog -
[   10.460000] Button Hotplug driver version 0.4.1
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
jffs2 is ready
jffs2 is ready
[   14.910000] jffs2: notice: (320) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 11 of xref (0 dead, 2 orphan) found.
switching to overlay
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[   16.480000] NET: Registered protocol family 10
[   16.500000] nf_conntrack version 0.5.0 (956 buckets, 3824 max)
[   16.530000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   16.560000] u32 classifier
[   16.570000]     input device check on
[   16.580000]     Actions configured
[   16.600000] Mirror/redirect action on
[   16.610000] Failed to load ipt action
[   16.640000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   16.670000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   16.720000] Ebtables v2.0 registered
[   16.740000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.900000] xt_time: kernel timezone is -0000
[   16.940000] cfg80211: Calling CRDA to update world regulatory domain
[   16.960000] cfg80211: World regulatory domain updated:
[   16.970000] cfg80211:  DFS Master region: unset
[   16.990000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   17.020000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   17.050000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   17.070000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   17.100000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   17.130000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   17.150000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   17.180000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   17.210000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   17.240000] PPP generic driver version 2.4.2
[   17.260000] NET: Registered protocol family 24
[   17.500000] Realtek WLAN driver - version 1.6 (2013-02-21)
[   17.520000] Adaptivity function - version 7.1
[   17.540000] Device Name = RTKWiFi0
[   17.550000] VIF_NUM=9
[   19.560000] UPHY: 8198c ASIC u2 of u3 40M phy patch
[   22.080000] Find Port=0 Device:Vender ID=818b10ec
[   22.600000] ROOT[0]=70:72:cf:d6:2d:0c
[   22.630000] VAP[0][1]=70:72:cf:d6:2d:0d
[   22.640000] VAP[0][2]=70:72:cf:d6:2d:0e
[   22.660000] VAP[0][3]=70:72:cf:d6:2d:0f
[   22.680000] VAP[0][4]=70:72:cf:d6:2d:10
[   22.700000] VAP[0][5]=70:72:cf:d6:2d:11
[   22.710000] VAP[0][6]=70:72:cf:d6:2d:12
[   22.730000] VAP[0][7]=70:72:cf:d6:2d:13
[   27.820000] device eth0 entered promiscuous mode
[   27.830000] br-lan: port 1(eth0) entered forwarding state
[   27.850000] br-lan: port 1(eth0) entered forwarding state
[   27.880000] IPv6: ADDRCONF(NETDEV_UP): br-captive: link is not ready
[   29.660000] [rtl_getMac][wlan0] 70:72:ffffffcf:ffffffd6:2d:0c
[   29.700000] FORCE PHY_BAND_2G & BGN!!
[   29.700000]
[   29.720000]
[   29.720000]
[   29.720000] ************* Initialize MAC/PHY parameter *************
[   29.720000] [MAC_REG_8192Emp]
[   29.720000] [PHY_REG_8192E_hp]
[   29.720000] [PHY_REG_PG_8192E_new]
[   29.720000] [AGC_TAB_8192E_hp]
[   29.720000] [RadioA_8192E_hp]
[   29.720000] [RadioB_8192E_hp]
[   29.720000] [TXPWR_LMT_92EE_new]
[   30.720000] device wlan0 entered promiscuous mode
[   30.720000] br-lan: port 1(eth0) entered forwarding state
[   30.760000] br-captive: port 1(wlan0) entered forwarding state
[   30.770000] br-captive: port 1(wlan0) entered forwarding state
[   30.790000] IPv6: ADDRCONF(NETDEV_CHANGE): br-captive: link becomes ready
[   30.840000] FORCE PHY_BAND_2G & BGN!!
[   30.840000]
[   30.860000]
[   30.860000]
[   30.860000] ************* Initialize MAC/PHY parameter *************
[   30.860000] [MAC_REG_8192Emp]
[   30.860000] [PHY_REG_8192E_hp]
[   30.860000] [PHY_REG_PG_8192E_new]
[   30.860000] [AGC_TAB_8192E_hp]
[   30.860000] [RadioA_8192E_hp]
[   30.860000] [RadioB_8192E_hp]
[   30.860000] [TXPWR_LMT_92EE_new]
[   32.770000] br-captive: port 1(wlan0) entered forwarding state
procd: - init complete -
[   33.460000] wifidog uses obsolete (PF_INET,SOCK_PACKET)

lazy***

潘多拉哪个不是在搞这货吗？1074Kc和MT7621差不多吧

zhl***

这个有点6了  磊科N285G  也是RTL8198  你这个带C  磊科的拆机不带C 不知道能不能通刷  想不到你这个U还有定制的op固件 神了

lazy***

zhl416 发表于 2016-11-15 01:33
这个有点6了  磊科N285G  也是RTL8198  你这个带C  磊科的拆机不带C 不知道能不能通刷  想不到你这个U还有 ...

8198的SDK本身就是op，只是版本比较久了

zwen***

lazywifi 发表于 2016-11-15 05:15
8198的SDK本身就是op，只是版本比较久了

哎。看样子是没得刷了。

l***

RTL的固件没有！！

血洗***

螃蟹真行难

zwen***

血洗刀锋 发表于 2016-11-15 14:10
螃蟹真行难

是啊。第一个吃螃蟹的人是得吃多少苦。

minm***

https://github.com/Wanyor/openwrt-rtk
http://downloads.openwrt.org.cn/PandoraBox/RTL8198CS_EVB/
或许有参考价值

zwen***

minmemory 发表于 2016-11-17 08:01
https://github.com/Wanyor/openwrt-rtk
http://downloads.openwrt.org.cn/PandoraBox/RTL8198CS_EVB/
或 ...

谢谢！
你的回复是目前最有建设性的
PandoraBox的8198C固件我前几天试过，能启动，无线无法使用，有线能用但是不稳定，有时候几分钟自动重启，有时候十几分钟自动重启。
Wanyor的还没试过。

路由***

楼主，有备份原厂固件么，如备份了能发一份给我研究下，谢谢！

Om***

楼主，有备份原厂固件么
身邊有台雜牌 8198+8192 原始固件有點問題
我有備份固件

打算過陣子刷285g 試試

zwen***

已经出给一个论坛的朋友了   没备份了

4732***

我也有一个，RTL8198C 的路由  AC1200规格  带USB  ，拷贝速速很华硕的一样  写入27M/s  读取17M/s  确实比老一代RTL8198强，可惜没固件

njcor***

473253327 发表于 2017-3-2 20:56
我也有一个，RTL8198C 的路由  AC1200规格  带USB  ，拷贝速速很华硕的一样  写入27M/s  读取17M/s  确实比 ...

请问下你这个是什么型号的机器？