|
|
TP1，我用万用表测量过，电压为3.31V，说明是VCC。
TP2，是GND。
TP5和TP6为RXD,TXD。
下面是输出信息：
U-Boot 1.1.4 (Jan 22 2013 - 00:11:52)
U-boot AP123
DRAM: 16 MB
Top of RAM usable for U-Boot at: 81000000
Reserving 139k for U-Boot at: 80fdc000
Reserving 192k for malloc() at: 80fac000
Reserving 44 Bytes for Board Info at: 80fabfd4
Reserving 36 Bytes for Global Data at: 80fabfb0
Reserving 128k for boot params() at: 80f8bfb0
Stack Pointer at: 80f8bf98
Now running in RAM - U-Boot at: 80fdc000
Flash Manuf Id 0x1c, DeviceId0 0x30, DeviceId1 0x16
flash size 4MB, sector count = 64
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
wasp reset mask:c03300
WASP ----> S27 PHY
: cfg1 0x80000000 cfg2 0x7114
eth0: 8c:21:0a:74:39:e9
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
WASP ----> S27 PHY
: cfg1 0xf cfg2 0x7214
eth1: 8c:21:0a:74:39:e8
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Load Default Boot Params.
Autobooting in 1 seconds
Uncompressing...done
W崱ス潄interface lo0... done
Rx clbufs 2048 each of size 1756
eth_rx_netpool_init: allocated, pDmaBuf=0x80b78850, buffend = 80eea854
ATHRS27: resetting s27
ATHRS27: s27 reset done
eth_rx_netpool_init: done already!
Attached IPv4 interface to mirror unit 0
usrAppInitEx: 130: GPIO_OE = 30310
usrAppInitEx: 131: CP0 CONFIG = 80208483
usrAppInitEx: 132: CP0 CONFIG1 = bee3519e
-->starting wireless...
APCFG task id 80996b10
sysWlanInit ...
Create WLAN event task tWLANEventTask
Create mem partion 0x809752e0 for size 86016
AH_CAL_IN_FLASH_AHB
Boostrap clock 25MHz
ar9300RadioAttach: Need analog access recipe!!
Restoring Cal data from Flash
ath_get_caps[4703] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[4678] tx chainmask mismatch actual 3 sc_chainmak 0
Create OS_MESGQ Successfully at 0x80954070
osifp->queue_head = 0x80954370
ag7240MemInit: allocated, dmabuf=0x80660650, buffend = 80922854
Entering Task Loop
Entering WLAN event Task Loop
ERROR:wireless OR ACL disable
sending message 806364d0,24
sending message 806364d0,24
TDDP: Now listening client request.
tddp is running.
httpInit: System File Registry successfully initialized.
httpInit: System File Manager successfully initialized.
httpInit: File System RPM successfully initialized.
httpInit: RPM dispatcher successfully initialized.
httpInit: MIME type guessing RPM successfully initialized.
httpInit: http Password Checking successfully initialized.
httpInit: http Access Control successfully initialized.
Software Platform for MIPS
Copyright(C) 2001-2010 by TP-LINK TECHNOLOGIES CO., LTD.
Starting WLAN !! Creation date: !! Apr 14 2013, 19:44:53
# AP_STARTMODE=standard
AP_ENABLE=1
ATH_COUNTRYCODE=156
wlan_vap_create : enter. devhandle=0x80447ba0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x80447ba0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
osif_ioctl_create_vap: vap 0x80ffe970 vap->iv_unit 0
ieee80211_end_load: load done
ath0 end flag = 0x00028802
default
default
default
IEE80211-FREQ IOCTL vap 0x80ffe970 0,0,0
AP_CHMODE=11NGHT40PLUS
WLAN IOCTL AP_CHMODE=11NGHT40PLUS=11NGHT20=11NGHT40PLUS=1003
IEE80211-MODE IOCTL 1,11NGHT40PLUS,13
set mode 11,-2130709132,6
set mode retv 0
WLAN IOCTL AP_PRIMARY_CH=auto=6=auto=1002
IEE80211-FREQ IOCTL vap 0x80ffe970 0,0,11
WLAN IOCTL PUREG=0=0=0=1004
IEEE80211-SETPURGE IOCTL 0
WLAN IOCTL AP_HIDE_SSID=0=0=0=1005
IEEE80211-SETHIDESSIDIOCTL 0
WLAN IOCTL AP_ISOLATION=0=0=0=1034
IEE80211-setparam-nobridge 0
WLAN IOCTL AP_TX11NRATE==0x0=0x0=1041
set auto rate
WLAN IOCTL AP_11G_PROTECTION==0=0=1042
WLAN IOCTL AP_BEACON_INTERVAL=100=100=100=1043
WLAN IOCTL AP_FRAGMENT_THRESHOLD=2346=2346=2346=1044
WLAN IOCTL AP_RTS_THRESHOLD=2346=2347=2346=1046
WLAN IOCTL AP_DTIM_PERIOD=1=1=1=1045
WLAN IOCTL AP_WMM_ENABLE=1=1=1=1051
ieee80211_vap_wme_set
WLAN IOCTL AP_WMM_NOACK==0=0=1052
IOCTL set wmm noack 0
WLAN IOCTL AP_CYPHER_2==CCMP=CCMP=1000
Get EIOCGADDR
WLAN IOCTL AP_NO_EDGE_CH==0=0=1056
WLAN IOCTL AP_MCASTRATE==0=0=1018
WLAN IOCTL AP_MACFILTER_MODE==0=0=1038
WLAN IOCTL AP_MACFILTER_LIST====1000
Get EIOCGADDR
WLAN IOCTL AP_SHORT_GI=1=1=1=1055
WLAN IOCTL AP_DISABLECOEXT=1=0=1=1075
WLAN IOCTL AP_SSID=TP-LINK_7439E8=Ath_AP123ng=TP-LINK_7439E8=1001
IEE80211-ESSID IOCTL 1,TP-LINK_7439E8,15
AP_CHMODE=11NGHT40PLUS
AP_CWMMODE=1
IEE80211-CWMMODE IOCTL 1
AP_AMPDU=0
AP_PURE_N=0
AP_TX_CHAINMASK=3
AP_RX_CHAINMASK=3
AP_SECMODE=None
WPS_ENABLE=1
AP_MACFILTER_MODE=0
ieee80211_open
WLAN IOCTL AP_BASICRATES==0=0=1039
WLAN IOCTL AP_DEBUG=0=0=0=1062
WLAN IOCTL AP_TX_POWER==0=0=1073
Starting Hostapd
AP_SSID=TP-LINK_7439E8
AP_HOSTAPD_DEBUG=0
AP_IPADDR=192.168.1.2
AP_SECMODE=None
WPS BSS init
WPS_ENABLE=1
WPS_PIN=25764857
WPS_STATE=1
1136073605.416667: wps_led_init: LED state UNCONFIGURED
AP_SECMODE=None
WPS OPEN BSS init
starting hostapd ...
Hostapd task Created 80ffa4a0
Task details [80ffa4a0,,64,809968a8]
Adding ath0 in bridge ...
default
Set EIOCGMIB2
default
Entering Hostapd Main
default
Set EIOCGMIB2
attached backend socket .
Attached backend socket for eth0
Attached backend socket for eth1
Attached backend socket for mirror 0
@@@@ kris-hostapd vapid=0 @@@@@ wiface=ath0 @@@@
**** [0,1,0,0192.168.1.2,]****
Just before eloop_run()
*** setup interface1 started ****
Eapol sockfd=27
Get EIOCGADDR
MAC address ffffff8c,21,a,74,39,ffffffe8
link _ubind0,0,0,0,0,0
IEE80211-IWMODE IOCTL 3
IEE80211-setparam-privacy 0
1136073607.416667: Defaulted uuid based on mac addr 8c:21:0a:74:39:e8
ieee80211_ioctl_setappiebuf
ieee80211_ioctl_setappiebuf
ieee80211_ioctl_setappiebuf
1136073607.416667: madwifi_start_receive_prob_req Enter
Madwifi init completed
1136073607.416667: ENTER eap_wps_disable, reason=7
*** setup interface1 completed ****
*** setup interface2 started ****
1136073607.433333: Flushing old station entries
IOCTL setmlme
[ieee80211_ioctl_setmlme:1887] data=0x80ff9fc0,data->pointer=0x80ffa010, data->length=42
[ieee80211_ioctl_setmlme:1893] mlme->im_op=3
1136073607.450000: Deauthenticate all stations
IEE80211-setparam-privacy 0
ieee80211_ioctl_delkey : idk_keyix=0
ieee80211_ioctl_delkey : idk_keyix=1
ieee80211_ioctl_delkey : idk_keyix=2
ieee80211_ioctl_delkey : idk_keyix=3
Using interface ath0 with hwaddr 8c:21:0a:74:39:e8 and ssid 'TP-LINK_7439E8'
1136073607.483333: SSID - hexdump_ascii(len=14):
54 50 2d 4c 49 4e 4b 5f 37 34 33 39 45 38 TP-LINK_7439E8
1136073607.483333: PSK (ASCII passphrase) - hexdump_ascii(len=0):
1136073607.750000: PSK (from passphrase) - hexdump(len=32): 21 3c 67 a3 9d c6 22 23 c8 09 2e 15 1d 53 99 58 b7 70 af e1 f9 5a 28 34 a0 dc e3 59 3b 6f 5f 89
IEE80211-ESSID IOCTL 1,TP-LINK_7439E8,15
osif_vap_init :vap up
IEE80211-setparam-authmode 1
osif_vap_init :vap up
osif_vap_init 0
hostapd_ctrl_iface_init
1136073607.800000: upnp_wps_device_init called
1136073607.800000: upnp_wps_device ssdp_listener_start failure!
1136073607.800000: upnp_wps_device_stop ENTER
1136073607.800000: upnp_wps_device_deinit called
1136073607.800000: upnp_wps_device_stop ENTER
1136073607.800000: Failed to initialize UPnP state machine
1136073607.800000: Continuing with WPS UPnP disabled.
****setup interface2 completed****
1136073607.800000: ath0: Setup of interface done.
****setup interface finalized ****
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2016-4-3 00:09
显身卡
