703换8MROM,刷OPENWRT后无线网卡无法识别了

myshadow

703换8MROM,刷OPENWRT后无线网卡无法识别了
启动记录如下,哪位兄弟能帮我看看是什么问题,谢谢
Starting kernel ...
[    0.000000] Linux version 3.3.8 (liuviking@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #3 Sat Jun 30 09:34:30 PDT 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61792k/65536k available (2075k kernel code, 3744k reserved, 395k data, 200k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.340000] bio: create slab <bio-0> at 0
[    0.340000] Switching to clocksource MIPS
[    0.350000] NET: Registered protocol family 2
[    0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.360000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.370000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.370000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.380000] TCP reno registered
[    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] NET: Registered protocol family 1
[    0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.430000] msgmni has been set to 120
[    0.430000] io scheduler noop registered
[    0.440000] io scheduler deadline registered (default)
[    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.450000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.470000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.470000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.480000] 5 tp-link partitions found on MTD device spi0.0
[    0.480000] Creating 5 MTD partitions on "spi0.0":
[    0.490000] 0x000000000000-0x000000020000 : "u-boot"
[    0.490000] 0x000000020000-0x0000000fc7c0 : "kernel"
[    0.500000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.510000] 0x0000000fc7c0-0x0000007f0000 : "rootfs"
[    0.520000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.530000] mtd: partition "rootfs" set to be root filesystem
[    0.530000] mtd: partition "rootfs_data" created automatically, ofs=370000, len=480000
[    0.540000] 0x000000370000-0x0000007f0000 : "rootfs_data"
[    0.550000] 0x0000007f0000-0x000000800000 : "art"
[    0.550000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.800000] ag71xx_mdio: probed
[    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.410000] TCP westwood registered
[    1.420000] NET: Registered protocol family 17
[    1.420000] 8021q: 802.1Q VLAN Support v1.8
[    1.430000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.440000] Freeing unused kernel memory: 200k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    6.780000] eth0: link up (100Mbps/Full duplex)
[    6.840000] JFFS2 notice: (408) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 31 of xref (0 dead, 20 orphan) found.
switching to jffs2
- init -
[    6.950000] eth0: link down
Please press Enter to activate this console. [    8.830000] Compat-wireless backport release: compat-wireless-2012-05-16-3-gde86a47
[    8.830000] Backport based on wireless-testing.git master-2012-05-29
[    8.840000] compat.git: wireless-testing.git
[    8.870000] cfg80211: Calling CRDA to update world regulatory domain
[    8.880000] cfg80211: World regulatory domain updated:
[    8.880000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.890000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.900000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.900000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.910000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.920000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.400000] cfg80211: World regulatory domain updated:
[    9.400000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.410000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.420000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    9.420000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    9.430000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.440000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.880000] usbcore: registered new interface driver usbfs
[    9.880000] usbcore: registered new interface driver hub
[    9.890000] usbcore: registered new device driver usb
[   10.530000] ath: phy0: Unable to initialize hardware; initialization status: -5
[   10.540000] ath9k ar933x_wmac: failed to initialize device
[   10.540000] ath9k: probe of ar933x_wmac failed with error -5
[   10.680000] PPP generic driver version 2.4.2
[   11.250000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.470000] NET: Registered protocol family 24
[   11.500000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   11.510000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[   11.510000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[   11.550000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[   11.570000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[   11.570000] hub 1-0:1.0: USB hub found
[   11.570000] hub 1-0:1.0: 1 port detected
[   11.600000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
[   11.820000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   11.930000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   11.940000] uhci_hcd: USB Universal Host Controller Interface driver
[   12.140000] i2c /dev entries driver
[   12.190000] usbcore: registered new interface driver snd-usb-audio
[   12.310000] Linux video capture interface: v2.00
[   12.490000] gspca_main: v2.14.0 registered
[   12.510000] usbcore: registered new interface driver zc3xx
[   12.530000] usbcore: registered new interface driver uvcvideo
[   12.540000] USB Video Class driver (1.1.1)
[   15.370000] device eth0 entered promiscuous mode
[   15.960000] eth0: link up (100Mbps/Full duplex)
[   15.960000] br-lan: port 1(eth0) entered forwarding state
[   15.960000] br-lan: port 1(eth0) entered forwarding state
[   17.960000] br-lan: port 1(eth0) entered forwarding state

myshadow

我换了另一个固件,现在报错变成-22了 请帮我看看.谢谢
Starting kernel ...

[    0.000000] Linux version 3.2.5 (xiaobiao@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Wed Feb 29 19:18:12 CST 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61788k/65536k available (2067k kernel code, 3748k reserved, 397k data, 192k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:48
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is TP-LINK TL-WR703N v1
[    0.330000] bio: create slab <bio-0> at 0
[    0.340000] Switching to clocksource MIPS
[    0.350000] NET: Registered protocol family 2
[    0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.350000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.350000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.360000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.370000] TCP reno registered
[    0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.380000] NET: Registered protocol family 1
[    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.410000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.420000] msgmni has been set to 120
[    0.430000] io scheduler noop registered
[    0.430000] io scheduler deadline registered (default)
[    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.440000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.450000] console [ttyATH0] enabled, bootconsole disabled
[    0.460000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.470000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.470000] 5 tp-link partitions found on MTD device spi0.0
[    0.480000] Creating 5 MTD partitions on "spi0.0":
[    0.480000] 0x000000000000-0x000000020000 : "u-boot"
[    0.490000] 0x000000020000-0x0000000fb014 : "kernel"
[    0.490000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.510000] 0x0000000fb014-0x0000007f0000 : "rootfs"
[    0.510000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.520000] mtd: partition "rootfs" set to be root filesystem
[    0.530000] mtd: partition "rootfs_data" created automatically, ofs=610000, len=1E0000
[    0.530000] 0x000000610000-0x0000007f0000 : "rootfs_data"
[    0.540000] 0x0000007f0000-0x000000800000 : "art"
[    0.550000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.900000] ag71xx_mdio: probed
[    0.900000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.510000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.510000] TCP westwood registered
[    1.520000] NET: Registered protocol family 17
[    1.520000] 8021q: 802.1Q VLAN Support v1.8
[    1.550000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.550000] Freeing unused kernel memory: 192k freed
[    6.260000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[    6.560000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    9.870000] eth0: link up (100Mbps/Full duplex)
jffs2 not ready yet; using ramdisk
- init -
[   10.130000] eth0: link down
[   13.600000] Compat-wireless backport release: compat-wireless-2012-01-16-14-g02166d5
[   13.600000] Backport based on wireless-testing.git master-2012-02-06
[   13.640000] cfg80211: Calling CRDA to update world regulatory domain
[   14.290000] NET: Registered protocol family 10
[   14.760000] cfg80211: World regulatory domain updated:
[   14.760000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   14.770000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.770000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.780000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   14.790000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   14.800000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   15.500000] SCSI subsystem initialized
[   16.020000] usbcore: registered new interface driver usbfs
[   16.030000] usbcore: registered new interface driver hub
[   16.030000] usbcore: registered new device driver usb
[   17.810000] usbcore: registered new interface driver rt2500usb
[   17.860000] usbcore: registered new interface driver rt73usb
[   17.890000] usbcore: registered new interface driver rtl8187
[   17.930000] ath: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[   17.930000] ath: random mac address will be used: e2:7f:66:32:21:15
[   17.940000] ath: Invalid EEPROM contents
[   17.940000] ath9k ar933x_wmac: failed to initialize device
[   17.950000] ath9k: probe of ar933x_wmac failed with error -22
[   17.970000] usbcore: registered new interface driver rt2800usb
[   18.730000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   19.230000] PPP generic driver version 2.4.2
[   19.290000] usbcore: registered new interface driver p54usb
[   19.320000] IPv6 over IPv4 tunneling driver
[   19.460000] GRE over IPv4 demultiplexor driver
[   19.580000] GRE over IPv4 tunneling driver
[   19.830000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   20.090000] NET: Registered protocol family 24
[   20.360000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   20.360000] ath79-ehci ar933x-ehci: Atheros built-in EHCI controller
[   20.370000] ath79-ehci ar933x-ehci: new USB bus registered, assigned bus number 1
[   20.400000] ath79-ehci ar933x-ehci: irq 3, io mem 0x1b000000
[   20.420000] ath79-ehci ar933x-ehci: USB 2.0 started, EHCI 1.00
[   20.420000] hub 1-0:1.0: USB hub found
[   20.420000] hub 1-0:1.0: 1 port detected
[   20.550000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
[   20.940000] usb 1-1: new high-speed USB device number 2 using ath79-ehci
[   21.380000] xt_time: kernel timezone is -0000
[   21.740000] xt_ipp2p: Unknown symbol HX_memmem (err 0)
[   21.770000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   21.900000] usbcore: registered new interface driver cdc_acm
[   21.900000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   22.040000] usbcore: registered new interface driver usblp
[   22.060000] usbcore: registered new interface driver usbserial
[   22.070000] USB Serial support registered for generic
[   22.070000] usbcore: registered new interface driver usbserial_generic
[   22.080000] usbserial: USB Serial Driver core
[   22.160000] Initializing USB Mass Storage driver...
[   22.170000] scsi0 : usb-storage 1-1:1.0
[   22.180000] usbcore: registered new interface driver usb-storage
[   22.180000] USB Mass Storage support registered.
[   22.310000] usbcore: registered new interface driver ums-alauda
[   22.330000] usbcore: registered new interface driver ums-cypress
[   22.350000] usbcore: registered new interface driver ums-datafab
[   22.370000] usbcore: registered new interface driver ums-freecom
[   22.400000] usbcore: registered new interface driver ums-isd200
[   22.420000] usbcore: registered new interface driver ums-jumpshot
[   22.440000] usbcore: registered new interface driver ums-karma
[   22.470000] usbcore: registered new interface driver ums-sddr09
[   22.490000] usbcore: registered new interface driver ums-sddr55
[   22.510000] usbcore: registered new interface driver ums-usbat
[   22.630000] usbcore: registered new interface driver zd1211rw
[   22.780000] USB Serial support registered for GSM modem (1-port)
[   22.790000] usbcore: registered new interface driver option
[   22.790000] option: v0.7.2:USB Driver for GSM modems
[   22.920000] fuse init (API version 7.17)

zhouweigsh

重刷ART

myshadow

zhouweigsh 发表于 2013-1-24 20:44
重刷ART

art是什么?怎么重刷?谢谢

shaoxingzhl

我可以给你刷好的

jhyetao

感谢分享

jhyetao

感谢分享