用JLINK修RG200E砖遇到问题，卡在Erasing block: 1 (addr = 1C000000)...

zj0***

卡在这里不动了

1. C:\BRJTAG>brjtag -probeonly /cable:2 /fc:112 /skipdetect /dma
   
2. 
   
3.         ===============================================
   
4.          Broadcom EJTAG Debrick Utility v2.0.5-hugebird
   
5.         ===============================================
   
6. 
   
7. 
   
8.   Open USB device: 0x1366:0101
   
9.   Vendor Name: [SEGGER]
   
10.   Produc Name: [J-Link]
    
11.   Serial No  : [123456]
    
12. 
    
13. Initializing J-Link HW Ver. 8.0
    
14. Set I/O speed to 3000 KHz
    
15. Detected target Vref = 3.339V
    
16. 
    
17. USB TAP device has been initialized. Please confirm VREF signal connected!
    
18. Press any key to continue... ONCE target board is powered on!
    
19. 
    
20. Probing bus ... Done
    
21. 
    
22. Detected IR Length is 5
    
23. 
    
24. CPU assumed running under LITTLE endian
    
25. 
    
26. CPU Chip ID: 00010000000010001100000101111111 (1008C17F)
    
27. *** CHIP DETECTION OVERRIDDEN ***
    
28. 
    
29.     - EJTAG IMPCODE ....... : 01100000010000010100000000000000 (60414000)
    
30.     - EJTAG Version ....... : 3.1
    
31.     - EJTAG DMA Support ... : No
    
32.     - EJTAG Implementation flags: R4k ASID_8 MIPS16 NoDMA MIPS32
    
33.     *** DMA Mode Forced On ***
    
34. 
    
35. Issuing Processor / Peripheral Reset ... Done
    
36. Enabling Memory Writes ... Skipped
    
37. Halting Processor ... <Processor did NOT enter Debug Mode!> ... Done
    
38. Clearing Watchdog ... Done
    
39. Loading CPU Configuration Code ... Skipped
    
40. *** Manually Selected a MX29GL128E Uni            (16MB) from Macronix
    
41. 
    
42. 
    
43. 
    
44. *** REQUESTED OPERATION IS COMPLETE ***
    
45. 
    
46. 
    
47. C:\BRJTAG>brjtag -flash:cfe /cable:2 /fc:112 /skipdetect /dma
    
48. 
    
49.         ===============================================
    
50.          Broadcom EJTAG Debrick Utility v2.0.5-hugebird
    
51.         ===============================================
    
52. 
    
53. 
    
54.   Open USB device: 0x1366:0101
    
55.   Vendor Name: [SEGGER]
    
56.   Produc Name: [J-Link]
    
57.   Serial No  : [123456]
    
58. 
    
59. Initializing J-Link HW Ver. 8.0
    
60. Set I/O speed to 3000 KHz
    
61. Detected target Vref = 3.339V
    
62. 
    
63. USB TAP device has been initialized. Please confirm VREF signal connected!
    
64. Press any key to continue... ONCE target board is powered on!
    
65. 
    
66. Probing bus ... Done
    
67. 
    
68. Detected IR Length is 5
    
69. 
    
70. CPU assumed running under LITTLE endian
    
71. 
    
72. CPU Chip ID: 00010000000010001100000101111111 (1008C17F)
    
73. *** CHIP DETECTION OVERRIDDEN ***
    
74. 
    
75.     - EJTAG IMPCODE ....... : 01100000010000010100000000000000 (60414000)
    
76.     - EJTAG Version ....... : 3.1
    
77.     - EJTAG DMA Support ... : No
    
78.     - EJTAG Implementation flags: R4k ASID_8 MIPS16 NoDMA MIPS32
    
79.     *** DMA Mode Forced On ***
    
80. 
    
81. Issuing Processor / Peripheral Reset ... Done
    
82. Enabling Memory Writes ... Skipped
    
83. Halting Processor ... <Processor did NOT enter Debug Mode!> ... Done
    
84. Clearing Watchdog ... Done
    
85. Loading CPU Configuration Code ... Skipped
    
86. *** Manually Selected a MX29GL128E Uni            (16MB) from Macronix
    
87. 
    
88.     - Flash Chip Window Start .... : 1C000000
    
89.     - Flash Chip Window Length ... : 01000000
    
90.     - Selected Area Start ........ : 1C000000
    
91.     - Selected Area Length ....... : 00040000
    
92. 
    
93. *** You Selected to Flash the CFE.BIN ***
    
94. 
    
95. =========================
    
96. Flashing Routine Started
    
97. =========================
    
98. Total Blocks to Erase: 2
    
99. 
    
100. Erasing block: 1 (addr = 1C000000)...

复制代码

zj0***

已经用编程器搞定

sc***

这是为什么呢，我也想买jlink