华硕wl330N3g的3G模块驱动不起来，各位帮看看

arnzh

cat /proc/bus/usb/devices的结果

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=1000 Rev= 0.00
S:  Manufacturer=USBModem
S:  Product=Qualcomm CDMA Technologies MSM
S:  SerialNumber=355477043037788
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms


驱动都装了，但是dmesg的结果
[   14.980000] PPP generic driver version 2.4.2
[   15.180000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.440000] NET: Registered protocol family 24
[   15.470000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   16.490000] rt3883-ehci rt3883-ehci: Ralink RT3883 built-in EHCI controller
[   16.500000] rt3883-ehci rt3883-ehci: new USB bus registered, assigned bus number 1
[   16.550000] rt3883-ehci rt3883-ehci: irq 26, io mem 0x101c0000
[   16.580000] rt3883-ehci rt3883-ehci: USB 2.0 started, EHCI 1.00
[   16.590000] hub 1-0:1.0: USB hub found
[   16.600000] hub 1-0:1.0: 1 port detected
[   16.630000] nf_conntrack version 0.5.0 (468 buckets, 1872 max)
[   16.930000] usb 1-1: new high-speed USB device number 2 using rt3883-ehci
[   17.130000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   17.140000] rt3883-ohci rt3883-ohci: Ralink RT3883 built-in OHCI controller
[   17.150000] rt3883-ohci rt3883-ohci: new USB bus registered, assigned bus number 2
[   17.170000] rt3883-ohci rt3883-ohci: irq 26, io mem 0x101c1000
[   17.240000] hub 2-0:1.0: USB hub found
[   17.250000] hub 2-0:1.0: 1 port detected
[   17.330000] usbcore: registered new interface driver cdc_acm
[   17.340000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   17.470000] usbcore: registered new interface driver usbserial
[   17.480000] USB Serial support registered for generic
[   17.490000] usbcore: registered new interface driver usbserial_generic
[   17.510000] usbserial: USB Serial Driver core
[   17.620000] USB Serial support registered for Qualcomm USB modem
[   17.640000] usbcore: registered new interface driver qcserial
[   24.180000] device eth0.1 entered promiscuous mode
[   24.190000] device eth0 entered promiscuous mode

就是死活没有ttyUSB的任何一个出现，郁闷啊，郁闷，哪位救个命啊，谢谢啦！

arnzh

搞定了，用了usb-modle-switch，把Vendor=05c6 ProdID=1000 Rev= 0.00转成了Vendor=05c6 ProdID=6000 Rev= 0.00
然后用kmod-usb-serial-option驱动成功，有ttyUSB0~4出现，但是又有新问题。
Dec  1 14:49:18 OpenWrt local2.info chat[856]: ATD*99***1#^M^M
Dec  1 14:49:18 OpenWrt local2.info chat[856]: CONNECT
Dec  1 14:49:18 OpenWrt local2.info chat[856]:  -- got it
Dec  1 14:49:18 OpenWrt local2.info chat[856]: send ( ^M)
Dec  1 14:49:18 OpenWrt daemon.info pppd[780]: Serial connection established.
Dec  1 14:49:18 OpenWrt daemon.info pppd[780]: Using interface 3g-wan3G
Dec  1 14:49:18 OpenWrt daemon.notice pppd[780]: Connect: 3g-wan3G <--> /dev/ttyUSB1
Dec  1 14:49:29 OpenWrt daemon.info dnsmasq[1034]: read /etc/hosts - 1 addresses
Dec  1 14:49:29 OpenWrt daemon.info dnsmasq-dhcp[1034]: read /etc/ethers - 0 addresses
Dec  1 14:49:49 OpenWrt daemon.warn pppd[780]: LCP: timeout sending Config-Requests
Dec  1 14:49:49 OpenWrt daemon.notice pppd[780]: Connection terminated.
Dec  1 14:49:50 OpenWrt daemon.notice pppd[780]: Modem hangup
Dec  1 14:49:50 OpenWrt daemon.info pppd[780]: Exit.

谁遇到过这种问题，帮忙看看。数据卡测试过，肯定没有欠费。

lwpk

我也有这货, 无奈原版固件太弱, 自己水平也不行

arnzh

我搞定了，哈哈，
要用usb-modle-switch，转成05c6：6000
驱动要用，kmod-usb-serial-option
其他就都是正常设置了。

lwpk

arnzh 发表于 2013-12-2 13:25
我搞定了，哈哈，
要用usb-modle-switch，转成05c6：6000
驱动要用，kmod-usb-serial-option

求固件........

arnzh

就是openwrt下载的基本固件啊？

yeshunter

arnzh 发表于 2013-12-2 23:07
就是openwrt下载的基本固件啊？

楼主可以指导我一下么？我在一个RT5350平台上移植3G模块，没有头绪