找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888广告投放联系QQ68610888
广告投放联系QQ68610888广告投放联系QQ68610888
查看: 12825|回复: 13

刷了OP的固件,可以启动,没有网卡驱动,求高手。。。。

[复制链接]
发表于 2013-12-7 00:41 | 显示全部楼层 |阅读模式
三元达双频四天线无线AP,本来是瘦AP,刷入了论坛里的一位朋友的OP固件。可以启动,但是没有网卡驱动,求高手帮忙。。
CPU:AR7161
2.4G网卡:AR9220
5.8G网卡:AR9227
附如下启动信息,等待高手解决,在线等。。。。


+Invalid PHY ID1 for enet0 port1.  Expected 0x0243, read 0xffff
Unkown speed read!
Unkown speed read!
Ethernet eth0: MAC address 00:03:7f:ff:ff:fe
IP: 0.0.0.0/255.255.255.0, Gateway: 0.0.0.0
Default server: 0.0.0.0
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version UNKNOWN - built 14:21:45, Mar 27 2010
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
Board: pb44
RAM: 0x80000000-0x84000000, [0x800511f0-0x80fe1000] available
FLASH: 0xbf000000 - 0xc0000000, 256 blocks of 0x00010000 bytes each.
== start led2 on
== Executing boot script in 3.000 seconds - enter ^C to abort
RedBoot> fis load -l kernel
Image loaded from 0x80060000-0x802e9418
config Image loaded from 0xbffe0000-0xbfff0000
RedBoot> exec -c "console=ttyS0,115200 mem=64M"
Now booting linux kernel:
Base address 0x80050000 Entry 0x80060000
Cmdline : console=ttyS0,115200 mem=64M
[    0.000000] Linux version 2.6.39.4 (kaka@kaka-ubuntu) (gcc version 4.5.4 2011
0808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Thu Jan 5 20:35:23 CST 2012
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7161 rev 2
[    0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.00
0MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
es: 16256
[    0.000000] Kernel command line:  board=AP2600I console=ttyS0,115200 ethaddr=
00.03.7f.ff.ff.fe rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[    0.000000] Writing ErrCtl register=00044882
[    0.000000] Readback ErrCtl register=00044882
[    0.000000] Memory: 61840k/65536k available (2018k kernel code, 3696k reserve
d, 389k data, 188k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, No
des=1
[    0.000000] NR_IRQS:80
[    0.000000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 512
[    0.070000] NET: Registered protocol family 16
[    0.070000] MIPS: machine is maselink ap2600i
[    0.570000] registering PCI controller with io_map_base unset
[    0.580000] bio: create slab <bio-0> at 0
[    0.580000] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    0.590000] pci 0000:00:11.0: BAR 0: set to [mem 0x10000000-0x1000ffff] (PCI
address [0x10000000-0x1000ffff])
[    0.590000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
[    0.600000] pci 0000:00:12.0: BAR 0: set to [mem 0x10010000-0x1001ffff] (PCI
address [0x10010000-0x1001ffff])
[    0.600000] PCI: mapping irq 72 to pin1@0000:00:11.0
[    0.610000] PCI: mapping irq 73 to pin1@0000:00:12.0
[    0.610000] Switching to clocksource MIPS
[    0.620000] NET: Registered protocol family 2
[    0.620000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.620000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.630000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.630000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.640000] TCP reno registered
[    0.640000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.650000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.650000] NET: Registered protocol family 1
[    0.670000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.670000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY
) (c) 2001-2006 Red Hat, Inc.
[    0.680000] msgmni has been set to 120
[    0.690000] io scheduler noop registered
[    0.690000] io scheduler deadline registered (default)
[    0.700000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.720000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.730000] console [ttyS0] enabled, bootconsole disabled
[    0.730000] console [ttyS0] enabled, bootconsole disabled
[    0.740000] Atheros AR71xx SPI Controller driver version 0.2.4
[    0.750000] m25p80 spi0.0: found s25sl12801, expected m25p80
[    0.760000] m25p80 spi0.0: s25sl12801 (16384 Kbytes)
[    0.760000] Searching for RedBoot partition table in spi0.0 at offset 0xfe000
0
[    0.850000] Searching for RedBoot partition table in spi0.0 at offset 0xff000
0
[    0.940000] 7 RedBoot partitions found on MTD device spi0.0
[    0.950000] Creating 7 MTD partitions on "spi0.0":
[    0.950000] 0x000000000000-0x000000040000 : "RedBoot"
[    0.960000] 0x000000040000-0x000000160000 : "kernel"
[    0.960000] 0x000000160000-0x000000f60000 : "rootfs"
[    0.970000] mtd: partition "rootfs" set to be root filesystem
[    0.980000] mtd: partition "rootfs_data" created automatically, ofs=330000, l
en=C30000
[    0.980000] 0x000000330000-0x000000f60000 : "rootfs_data"
[    0.990000] 0x000000f60000-0x000000fe0000 : "config"
[    1.000000] 0x000000fe0000-0x000000ff0000 : "board-config"
[    1.000000] 0x000000ff0000-0x000000fff000 : "FIS directory"
[    1.010000] 0x000000fff000-0x000001000000 : "RedBoot config"
[    1.020000] ag71xx_mdio: probed
[    1.020000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.330000] eth0: no PHY found with phy_mask=00000002
[    1.340000] Atheros AR71xx hardware watchdog driver version 0.1.0
[    1.340000] TCP westwood registered
[    1.350000] NET: Registered protocol family 17
[    1.350000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    1.360000] All bugs added by David S. Miller <davem@redhat.com>
[    1.370000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.380000] Freeing unused kernel memory: 188k freed
[    3.460000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[    6.940000] JFFS2 notice: (387) jffs2_build_xattr_subsystem: complete buildin
g xattr subsystem, 2 of xdatum (0 unchecked, 1 orphan) and 24 of xref (0 dead, 1
4 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [    8.340000] Compat-wireless back
port release: compat-wireless-2011-11-29
[    8.350000] Backport based on wireless-testing.git master-2011-12-01
[    8.430000] cfg80211: Calling CRDA to update world regulatory domain
[    8.670000] cfg80211: World regulatory domain updated:
[    8.670000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_g
ain, max_eirp)
[    8.680000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[    8.690000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[    8.700000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[    8.710000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[    8.710000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[    8.910000] SCSI subsystem initialized
[    9.060000] usbcore: registered new interface driver usbfs
[    9.060000] usbcore: registered new interface driver hub
[    9.070000] usbcore: registered new device driver usb
[    9.870000] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[   10.680000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=72
[   10.680000] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
[   10.850000] ieee80211 phy1: Atheros AR9287 Rev:2 mem=0xb0010000, irq=73
[   10.870000] cfg80211: Calling CRDA for country: AM
[   10.940000] cfg80211: Regulatory domain changed to country: AM
[   10.940000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_g
ain, max_eirp)
[   10.950000] cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000
mBm)
[   10.960000] cfg80211:     (5170000 KHz - 5250000 KHz @ 20000 KHz), (N/A, 1800
mBm)
[   10.970000] cfg80211:     (5250000 KHz - 5330000 KHz @ 20000 KHz), (N/A, 1800
mBm)
[   11.010000] PPP generic driver version 2.4.2
[   11.190000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.290000] NET: Registered protocol family 24
[   11.400000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)

BusyBox v1.19.3 (2012-01-05 20:27:34 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
ATTITUDE ADJUSTMENT (bleeding edge, r29637) ----------
  * 1/4 oz Vodka      Pour all ingredients into mixing
  * 1/4 oz Gin        tin with ice, strain into glass.
  * 1/4 oz Amaretto
  * 1/4 oz Triple sec
  * 1/4 oz Peach schnapps
  * 1/4 oz Sour mix
  * 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/#

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
发表于 2013-12-7 01:22 | 显示全部楼层
自己设置一下。。。怎么没驱动了??楼主从哪里看出来的
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

 楼主| 发表于 2013-12-7 06:20 | 显示全部楼层
a291899192 发表于 2013-12-7 01:22
自己设置一下。。。怎么没驱动了??楼主从哪里看出来的

root@OpenWrt:/# ifconfig
lo        Link encapocal Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:164880 errors:0 dropped:0 overruns:0 frame:0
          TX packets:164880 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:11211840 (10.6 MiB)  TX bytes:11211840 (10.6 MiB)

root@OpenWrt:/#
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

发表于 2013-12-7 10:35 | 显示全部楼层
晋鹏科技 发表于 2013-12-7 06:20
root@OpenWrt:/# ifconfig
lo        Link encapocal Loopback
          inet addr:127.0.0.1  Mask ...

看看  web界面的网络 ---接口  添加新的接口 里面有没有网卡可以选择的
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

 楼主| 发表于 2013-12-7 10:37 | 显示全部楼层
跟本进不了WEB界面 。。
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

发表于 2013-12-7 13:18 | 显示全部楼层
1.确实没有驱动网卡。也就是内核对网卡配置错误。
2.图片根本就看不清所有的硬件配置,包括网卡是如何连接的,直接soc 还是有第三方芯片。
3.继续找kaka修改内核,重新编译固件,最好给他提供样机
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

发表于 2013-12-7 19:14 | 显示全部楼层
zjhnzyf 发表于 2013-12-7 13:18
1.确实没有驱动网卡。也就是内核对网卡配置错误。
2.图片根本就看不清所有的硬件配置,包括网卡是如何连接 ...

为什么什么能识别到
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

 楼主| 发表于 2013-12-8 01:38 | 显示全部楼层
zjhnzyf 发表于 2013-12-7 13:18
1.确实没有驱动网卡。也就是内核对网卡配置错误。
2.图片根本就看不清所有的硬件配置,包括网卡是如何连接 ...

已经有人帮我修改了内核文件,人家让我自学,可是我不学不会,有内核文件,怎么通过超级终端更新。。。
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

发表于 2014-1-8 22:40 | 显示全部楼层
楼主有线网卡解决了吗 我也有和你一样的问题 有线口没驱动起来
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

发表于 2014-5-10 17:10 | 显示全部楼层
楼主你的固件整好了没有
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

发表于 2016-4-3 23:13 | 显示全部楼层
本帖最后由 htmq 于 2016-4-3 23:23 编辑

能看一下这个网站吗?也许有帮助:
https://forum.openwrt.org/viewtopic.php?id=43609

Vizio XWR100 主控、无线网卡是和我们的一样的,只是有线网有差别
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

发表于 2016-4-4 10:58 | 显示全部楼层

点评

楼主你的固件整好了没有  详情 回复 发表于 2016-8-23 21:05
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

发表于 2016-4-4 23:44 | 显示全部楼层
可以认到无线网卡!AR9280
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

发表于 2016-8-23 21:05 | 显示全部楼层
htmq 发表于 2016-4-4 10:58
https://github.com/cmtsij/openwrt/releases/tag/XWR100_LINUX_3.18.8

楼主你的固件整好了没有
只谈技术、莫论政事!(点击见详情) | 互相尊重、友善交流、切勿过度反应、玻璃心。胡乱输入灌水等操作将会被封禁ID。
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /2 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2026-8-23 19:31

Powered by Discuz! X3.5

© 2001-2026 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 电话:13506125623

快速回复 返回顶部 返回列表