找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 121488|回复: 213

继续测试:Linksys EA6500 v1 的TT固件

  [复制链接]
发表于 2013-12-7 15:22 | 显示全部楼层 |阅读模式
本帖最后由 bwq518 于 2014-10-20 19:49 编辑

感谢网友“盛鑫源”免费提供路由器。这是beta测试固件,英文界面。测试后请在此帖反馈。

下载链接:
https://mega.co.nz/#F!GJpVyKiI!MMX50qBZIZbmfqp_urKfmw

目录:TestingFirmwares/Linksys EA6500v1

刷机说明:
Linksys EA6500v1是有failsafe功能(双引导)的路由器,刷机过程与非failsafe的路由器有所区别。
从官方固件直刷步骤:
基本原则:首次从官方固件刷,TT固件只能刷在第一个分区。
1. 路由器正常启动后,登录官方界面,选择 左边菜单项【Connectivity】






2. 在弹出的页面中,点击按钮【Choose File】,选择tt固件,然后点击按钮【Start】






3. 静等刷机完成,路由器重启。
4. 重启后如果仍然出现官方界面,说明tt被刷到了第二个分区。没关系,在官方界面下做一次升级,升级必须用官方固件。
     升级完成,路由器会自动切换到另一个引导分区。
     在官方界面中,再次刷tt固件即可顺利刷入tt固件。重启后会出现tt登录界面。
5. 重启后如果进入了tt界面,恭喜你,刷机成功了。

在首次登录tt界面后,建议先做一次升级操作,选择同一个tt固件。升级操作会自动清除第二引导分区,以后即可随意升级tt固件了。


总结一下刷机要点:
在官方界面刷tt后,如果重启后仍然出现官方界面,则必须再刷一次官方固件,然后刷tt,并在tt重启后做一次升级tt。
在官方界面刷tt后,如果正常出现tt界面,则应该做一次tt的升级。
如果已经刷dd,可以通过dd界面直接刷tt。


2014.10.20.

=====================================================================================

已经上传了一个EA6500的固件,帮忙测试一下?
链接:  http://pan.baidu.com/s/1jGHS8Pw
1.        请测试直接在原厂Web界面升级是否可行?
2.        若原厂界面无法升级,先刷DD,在DD界面再升级看看?
3.        升级到TT后,看看型号识别是否正常?无线双频(2.4G,5G)是否正常?
4.        指示灯没有做特殊处理,观察一下是否正常?

若能把启动日志发给我,将有助于调试修正。 bwq518@gmail.com




本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

增强无线信号:国家选择US,5G固定40Mhz信道40,2.4g固定20Mhz,信道1.6.11,无线功率63, wlan降噪自动,禁用apsd省电模式  发表于 2015-1-30 16:30
大哥,你什么时候会更新?80%的时间帮你测试啊,不变砖就行````  发表于 2014-1-22 00:00

评分

参与人数 4贡献 +3 恩山币 +5 收起 理由
ink + 3 赞一个,你是我的呕像!
picc745514 + 1 一看就是觉得高端、大气、上档次!
lei8702 + 1 赞一个,你是我的呕像!
jzmno1 + 3 土豪专用

查看全部评分

我的恩山、我的无线 The best wifi forum is right here.
发表于 2013-12-7 15:55 | 显示全部楼层
初有此 奈何不支持  故卖之而入AC66   今闻将支持  恨啊  未顶住也
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 16:22 | 显示全部楼层
可惜没这机器,帮版主顶起来
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 16:49 | 显示全部楼层
本帖最后由 222ba 于 2013-12-7 17:09 编辑

我来测试。。稍后给答复

来了,变砖了、

  1. system is going down
  2. Guest access control is down
  3. committing syscfg
  4. eth2: WLC_GET_VAR(psta_if): Operation not supported
  5. system is going down in 7 sec
  6. iptables: Bad rule (does a matching rule exist in that chain?).
  7. iptables: Bad rule (does a matching rule exist in that chain?).
  8. [utopia] [wl] teardown wireless daemons
  9. killall: wps_monitor: no process killed
  10. killall: eapd: no process killed
  11. killall: nas: no process killed
  12. killall: cannot kill pid 5086: No such process
  13. killall: cannot kill pid 5141: No such process
  14. iptables: Bad rule (does a matching rule exist in that chain?).
  15. iptables: Bad rule (does a matching rule exist in that chain?).
  16. SIOCGIFFLAGS: No such device
  17. Device "br0" does not exist.
  18. [utopia] [wl] teardown wireless daemons
  19. killall: wps_monitor: no process killed
  20. killall: eapd: no process killed
  21. killall: nas: no process killed
  22. bridge br0 does not exist!
  23. delete the bridge br0
  24. SIOCGIFFLAGS: No such device
  25. bridge br0 doesn't exist; can't delete it
  26. Jul 28 17:13:41 mDNSResponder (Engineering Build) (Jan 18 2013 03:02:59) [4942]: stopping
  27. umount: mdev busy - remounted read-only
  28. system is going down now
  29. The system is going down NOW!
  30. Sent SIGTERM to all processes
  31. Sent SIGKILL toRestarting system.
  32. Please stand by while rebooting the system...
  33. cfe_led_init: start to set power LED and switch LEDs.
  34. Invalid command: "et"
  35. Available commands:



  36. Broadcom CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
  37. Build Date: Wed Jun 13 14:12:48 CST 2012 (lzh@team2compiler2)
  38. Copyright (C) 2000-2008 Broadcom Corporation.

  39. Init Arena
  40. Init Devs.
  41. This is a Serial Flash
  42. Boot partition size = 524288(0x80000)
  43. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  44. The NAND flash type is Samsung
  45. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  46. bcm_robo_enable_switch: EEE is disabled
  47. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.39.39.24
  48. CPU type 0x19749: 600MHz
  49. Tot mem: 131072 KBytes

  50. CFE mem:    0x80900000 - 0x80A67B40 (1473344)
  51. Data:       0x80951810 - 0x80954C90 (13440)
  52. BSS:        0x80954C90 - 0x80965B40 (69296)
  53. Heap:       0x80965B40 - 0x80A65B40 (1048576)
  54. Stack:      0x80A65B40 - 0x80A67B40 (8192)
  55. Text:       0x80900000 - 0x80951808 (333832)
  56. Boot:       0x00A68000 - 0x00AA8000
  57. Reloc:      I:00000000 - D:00000000

  58. Boot version: v0.1.8

  59. Device eth0:  hwaddr C8-D7-19-8B-AE-5D, ipaddr 192.168.1.1, mask 255.255.255.0
  60.         gateway not set, nameserver not set
  61. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
  62. Loading: Failed.
  63. Could not load :: Timeout occured
  64. boot wait load image command: load -raw -addr=0x80a67b40 -max=0x75984c0 :
  65. Booting(1): boot -raw -z -addr=0x80001000 -max=0x8ff000 nflash0.os2:
  66. Loader:raw Filesys:raw Dev:nflash0.os2 File: Options:(null)
  67. Loading: .. 5100 bytes read
  68. Entry at 0x80001000
  69. Closing network.
  70. Starting program at 0x80001000
  71. **Exception 8: EPC=8050006C, Cause=00000008 (TLBMissRd)
  72.                 RA=80001160, VAddr=C0000000

  73.         0  ($00) = 00000000     AT ($01) = 00000000
  74.         v0 ($02) = C0000000     v1 ($03) = FFFFFFFF
  75.         a0 ($04) = BFFF0000     a1 ($05) = BFFF0000
  76.         a2 ($06) = 30524448     a3 ($07) = 00008000
  77.         t0 ($08) = 10000819     t1 ($09) = 80500000
  78.         t2 ($10) = 80500000     t3 ($11) = 00000180
  79.         t4 ($12) = 000032C0     t5 ($13) = 80982C7C
  80.         t6 ($14) = 8097E51D     t7 ($15) = 000001A3
  81.         s0 ($16) = FEA3519E     s1 ($17) = 00000020
  82.         s2 ($18) = 00008000     s3 ($19) = 00000020
  83.         s4 ($20) = 00008000     s5 ($21) = 00000100
  84.         s6 ($22) = 00008000     s7 ($23) = 00008000
  85.         t8 ($24) = 8097E19C     t9 ($25) = 00000168
  86.         k0 ($26) = 20746120     k1 ($27) = 30313030
  87.         gp ($28) = 80959810     sp ($29) = 80A67100
  88.         fp ($30) = 00000020     ra ($31) = 80001160

  89. cfe_led_init: start to set power LED and switch LEDs.
  90. Invalid command: "et"
  91. Available commands:



  92. Broadcom CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
  93. Build Date: Wed Jun 13 14:12:48 CST 2012 (lzh@team2compiler2)
  94. Copyright (C) 2000-2008 Broadcom Corporation.

  95. Init Arena
  96. Init Devs.
  97. This is a Serial Flash
  98. Boot partition size = 524288(0x80000)
  99. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  100. The NAND flash type is Samsung
  101. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  102. bcm_robo_enable_switch: EEE is disabled
  103. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.39.39.24
  104. CPU type 0x19749: 600MHz
  105. Tot mem: 131072 KBytes

  106. CFE mem:    0x80900000 - 0x80A67B40 (1473344)
  107. Data:       0x80951810 - 0x80954C90 (13440)
  108. BSS:        0x80954C90 - 0x80965B40 (69296)
  109. Heap:       0x80965B40 - 0x80A65B40 (1048576)
  110. Stack:      0x80A65B40 - 0x80A67B40 (8192)
  111. Text:       0x80900000 - 0x80951808 (333832)
  112. Boot:       0x00A68000 - 0x00AA8000
  113. Reloc:      I:00000000 - D:00000000

  114. Boot version: v0.1.8

  115. Device eth0:  hwaddr C8-D7-19-8B-AE-5D, ipaddr 192.168.1.1, mask 255.255.255.0
  116.         gateway not set, nameserver not set
  117. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
  118. Loading: Failed.
  119. Could not load :: Timeout occured
  120. boot wait load image command: load -raw -addr=0x80a67b40 -max=0x75984c0 :
  121. Booting(1): boot -raw -z -addr=0x80001000 -max=0x8ff000 nflash0.os2:
  122. Loader:raw Filesys:raw Dev:nflash0.os2 File: Options:(null)
  123. Loading: .. 5100 bytes read
  124. Entry at 0x80001000
  125. Closing network.
  126. Starting program at 0x80001000
  127. **Exception 8: EPC=8050006C, Cause=00000008 (TLBMissRd)
  128.                 RA=80001160, VAddr=C0000000

  129.         0  ($00) = 00000000     AT ($01) = 00000000
  130.         v0 ($02) = C0000000     v1 ($03) = FFFFFFFF
  131.         a0 ($04) = BFFF0000     a1 ($05) = BFFF0000
  132.         a2 ($06) = 30524448     a3 ($07) = 00008000
  133.         t0 ($08) = 10000819     t1 ($09) = 80500000
  134.         t2 ($10) = 80500000     t3 ($11) = 00000180
  135.         t4 ($12) = 000032C0     t5 ($13) = 80982CB4
  136.         t6 ($14) = 8097E555     t7 ($15) = 000001A3
  137.         s0 ($16) = FEA3519E     s1 ($17) = 00000020
  138.         s2 ($18) = 00008000     s3 ($19) = 00000020
  139.         s4 ($20) = 00008000     s5 ($21) = 00000100
  140.         s6 ($22) = 00008000     s7 ($23) = 00008000
  141.         t8 ($24) = 8097E1D4     t9 ($25) = 00000168
  142.         k0 ($26) = 20746120     k1 ($27) = 30313030
  143.         gp ($28) = 80959810     sp ($29) = 80A67100
  144.         fp ($30) = 00000020     ra ($31) = 80001160

  145. cfe_led_init: start to set power LED and switch LEDs.
  146. Invalid command: "et"
  147. Available commands:



  148. Broadcom CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
  149. Build Date: Wed Jun 13 14:12:48 CST 2012 (lzh@team2compiler2)
  150. Copyright (C) 2000-2008 Broadcom Corporation.

  151. Init Arena
  152. Init Devs.
  153. This is a Serial Flash
  154. Boot partition size = 524288(0x80000)
  155. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  156. The NAND flash type is Samsung
  157. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  158. bcm_robo_enable_switch: EEE is disabled
  159. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.39.39.24
  160. CPU type 0x19749: 600MHz
  161. Tot mem: 131072 KBytes

  162. CFE mem:    0x80900000 - 0x80A67B40 (1473344)
  163. Data:       0x80951810 - 0x80954C90 (13440)
  164. BSS:        0x80954C90 - 0x80965B40 (69296)
  165. Heap:       0x80965B40 - 0x80A65B40 (1048576)
  166. Stack:      0x80A65B40 - 0x80A67B40 (8192)
  167. Text:       0x80900000 - 0x80951808 (333832)
  168. Boot:       0x00A68000 - 0x00AA8000
  169. Reloc:      I:00000000 - D:00000000

  170. Boot version: v0.1.8

  171. Device eth0:  hwaddr C8-D7-19-8B-AE-5D, ipaddr 192.168.1.1, mask 255.255.255.0
  172.         gateway not set, nameserver not set
  173. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
  174. Loading: Failed.
  175. Could not load :: Timeout occured
  176. boot wait load image command: load -raw -addr=0x80a67b40 -max=0x75984c0 :
  177. Booting(1): boot -raw -z -addr=0x80001000 -max=0x8ff000 nflash0.os2:
  178. Loader:raw Filesys:raw Dev:nflash0.os2 File: Options:(null)
  179. Loading: .. 5100 bytes read
  180. Entry at 0x80001000
  181. Closing network.
  182. Starting program at 0x80001000
  183. **Exception 8: EPC=8050006C, Cause=00000008 (TLBMissRd)
  184.                 RA=80001160, VAddr=C0000000

  185.         0  ($00) = 00000000     AT ($01) = 00000000
  186.         v0 ($02) = C0000000     v1 ($03) = FFFFFFFF
  187.         a0 ($04) = BFFF0000     a1 ($05) = BFFF0000
  188.         a2 ($06) = 30524448     a3 ($07) = 00008000
  189.         t0 ($08) = 10000819     t1 ($09) = 80500000
  190.         t2 ($10) = 80500000     t3 ($11) = 00000180
  191.         t4 ($12) = 000032C0     t5 ($13) = 80982C7C
  192.         t6 ($14) = 8097E51D     t7 ($15) = 000001A3
  193.         s0 ($16) = FEA3519E     s1 ($17) = 00000020
  194.         s2 ($18) = 00008000     s3 ($19) = 00000020
  195.         s4 ($20) = 00008000     s5 ($21) = 00000100
  196.         s6 ($22) = 00008000     s7 ($23) = 00008000
  197.         t8 ($24) = 8097E19C     t9 ($25) = 00000168
  198.         k0 ($26) = 20746120     k1 ($27) = 30313030
  199.         gp ($28) = 80959810     sp ($29) = 80A67100
  200.         fp ($30) = 00000020     ra ($31) = 80001160

  201. cfe_led_init: start to set power LED and switch LEDs.
  202. Invalid command: "et"
  203. Available commands:



  204. Broadcom CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
  205. Build Date: Wed Jun 13 14:12:48 CST 2012 (lzh@team2compiler2)
  206. Copyright (C) 2000-2008 Broadcom Corporation.

  207. Init Arena
  208. Init Devs.
  209. This is a Serial Flash
  210. Boot partition size = 524288(0x80000)
  211. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  212. The NAND flash type is Samsung
  213. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  214. bcm_robo_enable_switch: EEE is disabled
  215. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.39.39.24
  216. CPU type 0x19749: 600MHz
  217. Tot mem: 131072 KBytes

  218. CFE mem:    0x80900000 - 0x80A67B40 (1473344)
  219. Data:       0x80951810 - 0x80954C90 (13440)
  220. BSS:        0x80954C90 - 0x80965B40 (69296)
  221. Heap:       0x80965B40 - 0x80A65B40 (1048576)
  222. Stack:      0x80A65B40 - 0x80A67B40 (8192)
  223. Text:       0x80900000 - 0x80951808 (333832)
  224. Boot:       0x00A68000 - 0x00AA8000
  225. Reloc:      I:00000000 - D:00000000

  226. Boot version: v0.1.8

  227. Device eth0:  hwaddr C8-D7-19-8B-AE-5D, ipaddr 192.168.1.1, mask 255.255.255.0
  228.         gateway not set, nameserver not set
复制代码



再次追加,拔电重启,自动恢复官方固件了。

点评

求ttl怎么接?  详情 回复 发表于 2015-1-6 14:08
给个ttl的接点图吧 不知道ttl怎么接 求大哥指导! 现在无法打开web页了 插网线后面的网口灯亮  详情 回复 发表于 2015-1-6 13:58
支持一下  发表于 2013-12-11 10:25
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 16:54 | 显示全部楼层
没有此机器 只好转发扩散了 嘿嘿
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 17:27 | 显示全部楼层
[catsoul=3]你懂的。[/catsoul]
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 17:28 | 显示全部楼层
刷dd-wrt失败,自动恢复原厂固件。。没法继续了、

  1. system is going down
  2. Guest access control is down
  3. committing syscfg
  4. iptables: Bad rule (does a matching rule exist in that chain?).
  5. system is going down in 7 sec
  6. iptables: Bad rule (does a matching rule exist in that chain?).
  7. wl: wl driver adapter not found
  8. wl: wl driver adapter not found
  9. SIOCGIFFLAGS: No such device
  10. interface wl1.2 does not exist!
  11. device eth1 is not a slave of br0
  12. wl: wl driver adapter not found
  13. wl: wl driver adapter not found
  14. SIOCGIFFLAGS: No such device
  15. interface eth2 does not exist!
  16. wl: wl driver adapter not found
  17. wl: wl driver adapter not found
  18. wl: wl driver adapter not found
  19. [utopia] [wl] teardown wireless daemons
  20. killall: wps_monitor: no process killed
  21. killall: eapd: no process killed
  22. killall: nas: no process killed
  23. killall: cannot kill pid 5163: No such process
  24. iptables: Bad rule (does a matching rule exist in that chain?).
  25. iptables: Bad rule (does a matching rule exist in that chain?).
  26. SIOCGIFFLAGS: No such device
  27. Device "br0" does not exist.
  28. SIOCGIFFLAGS: No such device
  29. ifconfig: SIOCGIFFLAGS: No such device
  30. [utopia] [wl] teardown wireless daemons
  31. killall: wps_monitor: no process killed
  32. killall: eapd: no process killed
  33. killall: nas: no process killed
  34. bridge br0 does not exist!
  35. delete the bridge br0
  36. SIOCGIFFLAGS: No such device
  37. bridge br0 doesn't exist; can't delete it
  38. Jul 28 17:21:17 mDNSResponder (Engineering Build) (Jan 18 2013 03:02:59) [5025]: stopping
  39. system is going down now
  40. The system is going down NOW!
  41. Sent SIGTERM to all processes
  42. Sent SIGKILL to all processes
  43. Requesting system reboot
  44. Restarting system.
  45. Please stand by while rebooting the system...
  46. cfe_led_init: start to set power LED and switch LEDs.
  47. Invalid command: "et"
  48. Available commands:



  49. Broadcom CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
  50. Build Date: Wed Jun 13 14:12:48 CST 2012 (lzh@team2compiler2)
  51. Copyright (C) 2000-2008 Broadcom Corporation.

  52. Init Arena
  53. Init Devs.
  54. This is a Serial Flash
  55. Boot partition size = 524288(0x80000)
  56. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  57. The NAND flash type is Samsung
  58. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  59. bcm_robo_enable_switch: EEE is disabled
  60. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.39.39.24
  61. CPU type 0x19749: 600MHz
  62. Tot mem: 131072 KBytes

  63. CFE mem:    0x80900000 - 0x80A67B40 (1473344)
  64. Data:       0x80951810 - 0x80954C90 (13440)
  65. BSS:        0x80954C90 - 0x80965B40 (69296)
  66. Heap:       0x80965B40 - 0x80A65B40 (1048576)
  67. Stack:      0x80A65B40 - 0x80A67B40 (8192)
  68. Text:       0x80900000 - 0x80951808 (333832)
  69. Boot:       0x00A68000 - 0x00AA8000
  70. Reloc:      I:00000000 - D:00000000

  71. Boot version: v0.1.8

  72. Device eth0:  hwaddr C8-D7-19-8B-AE-5D, ipaddr 192.168.1.1, mask 255.255.255.0
  73.         gateway not set, nameserver not set
  74. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
  75. Loading: Failed.
  76. Could not load :: Timeout occured
  77. boot wait load image command: load -raw -addr=0x80a67b40 -max=0x75984c0 :
  78. Booting(1): boot -raw -z -addr=0x80001000 -max=0x8ff000 nflash0.os2:
  79. Loader:raw Filesys:raw Dev:nflash0.os2 File: Options:(null)
  80. Loading: ... 1366304 bytes read
  81. Entry at 0x80001000
  82. Closing network.
  83. Starting program at 0x80001000
  84. Linux version 3.11.5-rc1 (root@dd-wrt.buildserver) (gcc version 4.7.3 20121106 (prerelease) (Linaro GCC 4.7-2012.11) ) #45 Sun Oct 13 11:17:09 CEST 2013
  85. CPU revision is: 00019749 (MIPS 74Kc)
  86. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  87. found 256K nvram at 11000
  88. Determined physical RAM map:
  89. memory: 07fff000 @ 00000000 (usable)
  90. Zone ranges:
  91.   Normal   [mem 0x00000000-0x07ffefff]
  92.   HighMem  empty
  93. Movable zone start for each node
  94. Early memory node ranges
  95.   node   0: [mem 0x00000000-0x07ffefff]
  96. Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
  97. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  98. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32511
  99. Kernel command line: console=ttyS0,115200 root=1f05 rootfstype=squashfs noinitrd init=/bin/sh
  100. PID hash table entries: 512 (order: -1, 2048 bytes)
  101. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  102. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  103. Writing ErrCtl register=80000d00
  104. Readback ErrCtl register=80000d00
  105. Cache parity protection enabled
  106. Memory: 125072K/131068K available (3132K kernel code, 225K rwdata, 436K rodata, 292K init, 708K bss, 5996K reserved, 0K highmem)
  107. NR_IRQS:128
  108. CPU: BCM5300 rev 1 at 600 MHz
  109. bcm947xx_clockevent_set_mode: 1
  110. bcm947xx_clockevent_set_mode: 3
  111. console [ttyS0] enabled
  112. Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
  113. pid_max: default: 32768 minimum: 301
  114. Mount-cache hash table entries: 512
  115. NET: Registered protocol family 16
  116. bio: create slab <bio-0> at 0
  117. PCI: Initializing host
  118. PCI: Reset RC
  119. PCI: Initializing host
  120. PCI: Reset RC
  121. PCI: scanning bus 0
  122. PCI host bridge to bus 0000:00
  123. pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
  124. pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
  125. pci_bus 0000:00: root bus resource [bus 00-ff]
  126. PCI: Fixing up bus 0
  127. pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  128. pci 0000:00:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  129. PCI/PCIe coreunit 0 is set to bus 1.
  130. PCI: Fixing up bridge
  131. PCI: Fixing up bridge
  132. PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
  133. PCI: Fixing up bus 1
  134. PCI/PCIe coreunit 1 is set to bus 2.
  135. PCI: Fixing up bridge
  136. PCI: Fixing up bridge
  137. PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
  138. PCI: Fixing up bus 2
  139. Switched to clocksource MIPS
  140. NET: Registered protocol family 2
  141. TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  142. TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  143. TCP: Hash tables configured (established 1024 bind 1024)
  144. TCP: reno registered
  145. UDP hash table entries: 256 (order: 0, 4096 bytes)
  146. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  147. NET: Registered protocol family 1
  148. squashfs: version 3.0 (2006/03/15) Phillip Lougher
  149. msgmni has been set to 244
  150. alg: No test for stdrng (krng)
  151. io scheduler noop registered (default)
  152. HDLC line discipline maxframe=4096
  153. N_HDLC line discipline registered.
  154. Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
  155. serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a U6_16550A
  156. serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a U6_16550A
  157. brd: module loaded
  158. pflash: found no supported devices
  159. try to find cfe size up to 1048576
  160. no filesys. assume nflash devices
  161. bootloader size: 1048576
  162. nvram size: 65536
  163. Linksys NVRAM Hack
  164. Creating 2 MTD partitions on "bcmsflash":
  165. 0x000000000000-0x000000100000 : "cfe"
  166. 0x0000000c0000-0x000000100000 : "nvram"
  167. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  168. NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
  169. Bad block table found at page 65472, version 0x01
  170. Bad block table found at page 65408, version 0x01
  171. nand_read_bbt: bad block at 0x0000001a0000
  172. nand_read_bbt: bad block at 0x000004c20000
  173. nand_read_bbt: bad block at 0x000004fe0000
  174. nand_read_bbt: bad block at 0x000005100000
  175. nand_read_bbt: bad block at 0x000005860000
  176. Creating 2 MTD partitions on "brcmnand":
  177. 0x000000000000-0x000002000000 : "linux"
  178. 0x000002000000-0x000007f00000 : "ddwrt"
  179. lookup_nflash_rootfs_offset: offset = 0x0
  180. found trx at 0, len =13721600
  181. scan filesys at 1EB6A0
  182. nflash: nflash_read return 0
  183. Creating 2 MTD partitions on "nflash":
  184. 0x000000000000-0x000002000000 : "nandimage"
  185. 0x000002000000-0x000008000000 : "rootfs"
  186. mtd: partition "rootfs" set to be root filesystem
  187. add netgear bosrddata for pflash if exists
  188. add netgear bosrddata for sflash if exists
  189. tun: Universal TUN/TAP device driver, 1.6
  190. tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  191. PPP generic driver version 2.4.2
  192. PPP BSD Compression module registered
  193. PPP Deflate Compression module registered
  194. PPP MPPE Compression module registered
  195. NET: Registered protocol family 24
  196. Broadcom Watchdog Timer: 0.07 initialized.
  197. GACT probability NOT on
  198. Mirror/redirect action on
  199. Failed to load ipt action
  200. Simple TC action Loaded
  201. netem: version 1.3
  202. u32 classifier
  203.     Performance counters on
  204.     input device check on
  205.     Actions configured
  206. Netfilter messages via NETLINK v0.30.
  207. nf_conntrack version 0.5.0 (1954 buckets, 7816 max)
  208. nf_conntrack_rtsp v0.6.21 loading
  209. xt_time: kernel timezone is -0000
  210. ip_set: protocol 6
  211. gre: GRE over IPv4 demultiplexor driver
  212. nf_nat_rtsp v0.6.21 loading
  213. ip_tables: (C) 2000-2006 Netfilter Core Team
  214. TCP: bic registered
  215. TCP: cubic registered
  216. TCP: westwood registered
  217. TCP: highspeed registered
  218. TCP: hybla registered
  219. TCP: htcp registered
  220. TCP: vegas registered
  221. TCP: veno registered
  222. TCP: scalable registered
  223. TCP: lp registered
  224. TCP: yeah registered
  225. TCP: illinois registered
  226. NET: Registered protocol family 17
  227. Bridge firewalling registered
  228. 8021q: 802.1Q VLAN Support v1.8
  229. startup nvram driver
  230. found nvram
  231. List of all partitions:
  232. 1f00            1024 mtdblock0  (driver?)
  233. 1f01             256 mtdblock1  (driver?)
  234. 1f02           32768 mtdblock2  (driver?)
  235. 1f03           97280 mtdblock3  (driver?)
  236. 1f04           32768 mtdblock4  (driver?)
  237. 1f05           98304 mtdblock5  (driver?)
  238. No filesystem could mount root, tried:  squashfs
  239. Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)
  240. Rebooting in 3 seconds..Please stand by while rebooting the system...
  241. cfe_led_init: start to set power LED and switch LEDs.
  242. Invalid command: "et"
  243. Available commands:



  244. Broadcom CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
  245. Build Date: Wed Jun 13 14:12:48 CST 2012 (lzh@team2compiler2)
  246. Copyright (C) 2000-2008 Broadcom Corporation.

  247. Init Arena
  248. Init Devs.
  249. This is a Serial Flash
  250. Boot partition size = 524288(0x80000)
  251. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  252. The NAND flash type is Samsung
  253. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  254. bcm_robo_enable_switch: EEE is disabled
  255. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.39.39.24
  256. CPU type 0x19749: 600MHz
  257. Tot mem: 131072 KBytes

  258. CFE mem:    0x80900000 - 0x80A67B40 (1473344)
  259. Data:       0x80951810 - 0x80954C90 (13440)
  260. BSS:        0x80954C90 - 0x80965B40 (69296)
  261. Heap:       0x80965B40 - 0x80A65B40 (1048576)
  262. Stack:      0x80A65B40 - 0x80A67B40 (8192)
  263. Text:       0x80900000 - 0x80951808 (333832)
  264. Boot:       0x00A68000 - 0x00AA8000
  265. Reloc:      I:00000000 - D:00000000

  266. Boot version: v0.1.8

  267. Device eth0:  hwaddr C8-D7-19-8B-AE-5D, ipaddr 192.168.1.1, mask 255.255.255.0
  268.         gateway not set, nameserver not set
  269. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
  270. Loading: Failed.
  271. Could not load :: Timeout occured
  272. boot wait load image command: load -raw -addr=0x80a67b40 -max=0x75984c0 :
  273. Booting(1): boot -raw -z -addr=0x80001000 -max=0x8ff000 nflash0.os2:
  274. Loader:raw Filesys:raw Dev:nflash0.os2 File: Options:(null)
  275. Loading: ... 1366304 bytes read
  276. Entry at 0x80001000
  277. Closing network.
  278. Starting program at 0x80001000
  279. Linux version 3.11.5-rc1 (root@dd-wrt.buildserver) (gcc version 4.7.3 20121106 (prerelease) (Linaro GCC 4.7-2012.11) ) #45 Sun Oct 13 11:17:09 CEST 2013
  280. CPU revision is: 00019749 (MIPS 74Kc)
  281. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  282. found 256K nvram at 11000
  283. Determined physical RAM map:
  284. memory: 07fff000 @ 00000000 (usable)
  285. Zone ranges:
  286.   Normal   [mem 0x00000000-0x07ffefff]
  287.   HighMem  empty
  288. Movable zone start for each node
  289. Early memory node ranges
  290.   node   0: [mem 0x00000000-0x07ffefff]
  291. Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
  292. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  293. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32511
  294. Kernel command line: console=ttyS0,115200 root=1f05 rootfstype=squashfs noinitrd init=/bin/sh
  295. PID hash table entries: 512 (order: -1, 2048 bytes)
  296. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  297. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  298. Writing ErrCtl register=80000d00
  299. Readback ErrCtl register=80000d00
  300. Cache parity protection enabled
  301. Memory: 125072K/131068K available (3132K kernel code, 225K rwdata, 436K rodata, 292K init, 708K bss, 5996K reserved, 0K highmem)
  302. NR_IRQS:128
  303. CPU: BCM5300 rev 1 at 600 MHz
  304. bcm947xx_clockevent_set_mode: 1
  305. bcm947xx_clockevent_set_mode: 3
  306. console [ttyS0] enabled
  307. Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
  308. pid_max: default: 32768 minimum: 301
  309. Mount-cache hash table entries: 512
  310. NET: Registered protocol family 16
  311. bio: create slab <bio-0> at 0
  312. PCI: Initializing host
  313. PCI: Reset RC
  314. PCI: Initializing host
  315. PCI: Reset RC
  316. PCI: scanning bus 0
  317. PCI host bridge to bus 0000:00
  318. pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
  319. pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
  320. pci_bus 0000:00: root bus resource [bus 00-ff]
  321. PCI: Fixing up bus 0
  322. pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  323. pci 0000:00:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  324. PCI/PCIe coreunit 0 is set to bus 1.
  325. PCI: Fixing up bridge
  326. PCI: Fixing up bridge
  327. PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
  328. PCI: Fixing up bus 1
  329. PCI/PCIe coreunit 1 is set to bus 2.
  330. PCI: Fixing up bridge
  331. PCI: Fixing up bridge
  332. PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
  333. PCI: Fixing up bus 2
  334. Switched to clocksource MIPS
  335. NET: Registered protocol family 2
  336. TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  337. TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  338. TCP: Hash tables configured (established 1024 bind 1024)
  339. TCP: reno registered
  340. UDP hash table entries: 256 (order: 0, 4096 bytes)
  341. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  342. NET: Registered protocol family 1
  343. squashfs: version 3.0 (2006/03/15) Phillip Lougher
  344. msgmni has been set to 244
  345. alg: No test for stdrng (krng)
  346. io scheduler noop registered (default)
  347. HDLC line discipline maxframe=4096
  348. N_HDLC line discipline registered.
  349. Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
  350. serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a U6_16550A
  351. serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a U6_16550A
  352. brd: module loaded
  353. pflash: found no supported devices
  354. try to find cfe size up to 1048576
  355. no filesys. assume nflash devices
  356. bootloader size: 1048576
  357. nvram size: 65536
  358. Linksys NVRAM Hack
  359. Creating 2 MTD partitions on "bcmsflash":
  360. 0x000000000000-0x000000100000 : "cfe"
  361. 0x0000000c0000-0x000000100000 : "nvram"
  362. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  363. NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
  364. Bad block table found at page 65472, version 0x01
  365. Bad block table found at page 65408, version 0x01
  366. nand_read_bbt: bad block at 0x0000001a0000
  367. nand_read_bbt: bad block at 0x000004c20000
  368. nand_read_bbt: bad block at 0x000004fe0000
  369. nand_read_bbt: bad block at 0x000005100000
  370. nand_read_bbt: bad block at 0x000005860000
  371. Creating 2 MTD partitions on "brcmnand":
  372. 0x000000000000-0x000002000000 : "linux"
  373. 0x000002000000-0x000007f00000 : "ddwrt"
  374. lookup_nflash_rootfs_offset: offset = 0x0
  375. found trx at 0, len =13721600
  376. scan filesys at 1EB6A0
  377. nflash: nflash_read return 0
  378. Creating 2 MTD partitions on "nflash":
  379. 0x000000000000-0x000002000000 : "nandimage"
  380. 0x000002000000-0x000008000000 : "rootfs"
  381. mtd: partition "rootfs" set to be root filesystem
  382. add netgear bosrddata for pflash if exists
  383. add netgear bosrddata for sflash if exists
  384. tun: Universal TUN/TAP device driver, 1.6
  385. tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  386. PPP generic driver version 2.4.2
  387. PPP BSD Compression module registered
  388. PPP Deflate Compression module registered
  389. PPP MPPE Compression module registered
  390. NET: Registered protocol family 24
  391. Broadcom Watchdog Timer: 0.07 initialized.
  392. GACT probability NOT on
  393. Mirror/redirect action on
  394. Failed to load ipt action
  395. Simple TC action Loaded
  396. netem: version 1.3
  397. u32 classifier
  398.     Performance counters on
  399.     input device check on
  400.     Actions configured
  401. Netfilter messages via NETLINK v0.30.
  402. nf_conntrack version 0.5.0 (1954 buckets, 7816 max)
  403. nf_conntrack_rtsp v0.6.21 loading
  404. xt_time: kernel timezone is -0000
  405. ip_set: protocol 6
  406. gre: GRE over IPv4 demultiplexor driver
  407. nf_nat_rtsp v0.6.21 loading
  408. ip_tables: (C) 2000-2006 Netfilter Core Team
  409. TCP: bic registered
  410. TCP: cubic registered
  411. TCP: westwood registered
  412. TCP: highspeed registered
  413. TCP: hybla registered
  414. TCP: htcp registered
  415. TCP: vegas registered
  416. TCP: veno registered
  417. TCP: scalable registered
  418. TCP: lp registered
  419. TCP: yeah registered
  420. TCP: illinois registered
  421. NET: Registered protocol family 17
  422. Bridge firewalling registered
  423. 8021q: 802.1Q VLAN Support v1.8
  424. startup nvram driver
  425. found nvram
  426. List of all partitions:
  427. 1f00            1024 mtdblock0  (driver?)
  428. 1f01             256 mtdblock1  (driver?)
  429. 1f02           32768 mtdblock2  (driver?)
  430. 1f03           97280 mtdblock3  (driver?)
  431. 1f04           32768 mtdblock4  (driver?)
  432. 1f05           98304 mtdblock5  (driver?)
  433. No filesystem could mount root, tried:  squashfs
  434. Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)
  435. Rebooting in 3 seconds..Please stand by while rebooting the system...
  436. cfe_led_init: start to set power LED and switch LEDs.
  437. Invalid command: "et"
  438. Available commands:



  439. Broadcom CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
  440. Build Date: Wed Jun 13 14:12:48 CST 2012 (lzh@team2compiler2)
  441. Copyright (C) 2000-2008 Broadcom Corporation.

  442. Init Arena
  443. Init Devs.
  444. This is a Serial Flash
  445. Boot partition size = 524288(0x80000)
  446. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  447. The NAND flash type is Samsung
  448. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  449. bcm_robo_enable_switch: EEE is disabled
  450. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.39.39.24
  451. CPU type 0x19749: 600MHz
  452. Tot mem: 131072 KBytes

  453. CFE mem:    0x80900000 - 0x80A67B40 (1473344)
  454. Data:       0x80951810 - 0x80954C90 (13440)
  455. BSS:        0x80954C90 - 0x80965B40 (69296)
  456. Heap:       0x80965B40 - 0x80A65B40 (1048576)
  457. Stack:      0x80A65B40 - 0x80A67B40 (8192)
  458. Text:       0x80900000 - 0x80951808 (333832)
  459. Boot:       0x00A68000 - 0x00AA8000
  460. Reloc:      I:00000000 - D:00000000

  461. Boot version: v0.1.8

  462. Device eth0:  hwaddr C8-D7-19-8B-AE-5D, ipaddr 192.168.1.1, mask 255.255.255.0
  463.         gateway not set, nameserver not set
  464. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
  465. Loading: Failed.
  466. Could not load :: Timeout occured
  467. boot wait load image command: load -raw -addr=0x80a67b40 -max=0x75984c0 :
  468. Booting(1): boot -raw -z -addr=0x80001000 -max=0x8ff000 nflash0.os2:
  469. Loader:raw Filesys:raw Dev:nflash0.os2 File: Options:(null)
  470. Loading: ... 1366304 bytes read
  471. Entry at 0x80001000
  472. Closing network.
  473. Starting program at 0x80001000
  474. Linux version 3.11.5-rc1 (root@dd-wrt.buildserver) (gcc version 4.7.3 20121106 (prerelease) (Linaro GCC 4.7-2012.11) ) #45 Sun Oct 13 11:17:09 CEST 2013
  475. CPU revision is: 00019749 (MIPS 74Kc)
  476. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  477. found 256K nvram at 11000
  478. Determined physical RAM map:
  479. memory: 07fff000 @ 00000000 (usable)
  480. Zone ranges:
  481.   Normal   [mem 0x00000000-0x07ffefff]
  482.   HighMem  empty
  483. Movable zone start for each node
  484. Early memory node ranges
  485.   node   0: [mem 0x00000000-0x07ffefff]
  486. Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
  487. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  488. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32511
  489. Kernel command line: console=ttyS0,115200 root=1f05 rootfstype=squashfs noinitrd init=/bin/sh
  490. PID hash table entries: 512 (order: -1, 2048 bytes)
  491. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  492. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  493. Writing ErrCtl register=80000d00
  494. Readback ErrCtl register=80000d00
  495. Cache parity protection enabled
  496. Memory: 125072K/131068K available (3132K kernel code, 225K rwdata, 436K rodata, 292K init, 708K bss, 5996K reserved, 0K highmem)
  497. NR_IRQS:128
  498. CPU: BCM5300 rev 1 at 600 MHz
  499. bcm947xx_clockevent_set_mode: 1
  500. bcm947xx_clockevent_set_mode: 3
  501. console [ttyS0] enabled
  502. Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
  503. pid_max: default: 32768 minimum: 301
  504. Mount-cache hash table entries: 512
  505. NET: Registered protocol family 16
  506. bio: create slab <bio-0> at 0
  507. PCI: Initializing host
  508. PCI: Reset RC
  509. PCI: Initializing host
  510. PCI: Reset RC
  511. PCI: scanning bus 0
  512. PCI host bridge to bus 0000:00
  513. pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
  514. pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
  515. pci_bus 0000:00: root bus resource [bus 00-ff]
  516. PCI: Fixing up bus 0
  517. pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  518. pci 0000:00:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
  519. PCI/PCIe coreunit 0 is set to bus 1.
  520. PCI: Fixing up bridge
  521. PCI: Fixing up bridge
  522. PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
  523. PCI: Fixing up bus 1
  524. PCI/PCIe coreunit 1 is set to bus 2.
  525. PCI: Fixing up bridge
  526. PCI: Fixing up bridge
  527. PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
  528. PCI: Fixing up bus 2
  529. Switched to clocksource MIPS
  530. NET: Registered protocol family 2
  531. TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  532. TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  533. TCP: Hash tables configured (established 1024 bind 1024)
  534. TCP: reno registered
  535. UDP hash table entries: 256 (order: 0, 4096 bytes)
  536. UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
  537. NET: Registered protocol family 1
  538. squashfs: version 3.0 (2006/03/15) Phillip Lougher
  539. msgmni has been set to 244
  540. alg: No test for stdrng (krng)
  541. io scheduler noop registered (default)
  542. HDLC line discipline maxframe=4096
  543. N_HDLC line discipline registered.
  544. Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
  545. serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a U6_16550A
  546. serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a U6_16550A
  547. brd: module loaded
  548. pflash: found no supported devices
  549. try to find cfe size up to 1048576
  550. no filesys. assume nflash devices
  551. bootloader size: 1048576
  552. nvram size: 65536
  553. Linksys NVRAM Hack
  554. Creating 2 MTD partitions on "bcmsflash":
  555. 0x000000000000-0x000000100000 : "cfe"
  556. 0x0000000c0000-0x000000100000 : "nvram"
  557. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  558. NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
  559. Bad block table found at page 65472, version 0x01
  560. Bad block table found at page 65408, version 0x01
  561. nand_read_bbt: bad block at 0x0000001a0000
  562. nand_read_bbt: bad block at 0x000004c20000
  563. nand_read_bbt: bad block at 0x000004fe0000
  564. nand_read_bbt: bad block at 0x000005100000
  565. nand_read_bbt: bad block at 0x000005860000
  566. Creating 2 MTD partitions on "brcmnand":
  567. 0x000000000000-0x000002000000 : "linux"
  568. 0x000002000000-0x000007f00000 : "ddwrt"
  569. lookup_nflash_rootfs_offset: offset = 0x0
  570. found trx at 0, len =13721600
  571. scan filesys at 1EB6A0
  572. nflash: nflash_read return 0
  573. Creating 2 MTD partitions on "nflash":
  574. 0x000000000000-0x000002000000 : "nandimage"
  575. 0x000002000000-0x000008000000 : "rootfs"
  576. mtd: partition "rootfs" set to be root filesystem
  577. add netgear bosrddata for pflash if exists
  578. add netgear bosrddata for sflash if exists
  579. tun: Universal TUN/TAP device driver, 1.6
  580. tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
  581. PPP generic driver version 2.4.2
  582. PPP BSD Compression module registered
  583. PPP Deflate Compression module registered
  584. PPP MPPE Compression module registered
  585. NET: Registered protocol family 24
  586. Broadcom Watchdog Timer: 0.07 initialized.
  587. GACT probability NOT on
  588. Mirror/redirect action on
  589. Failed to load ipt action
  590. Simple TC action Loaded
  591. netem: version 1.3
  592. u32 classifier
  593.     Performance counters on
  594.     input device check on
  595.     Actions configured
  596. Netfilter messages via NETLINK v0.30.
  597. nf_conntrack version 0.5.0 (1954 buckets, 7816 max)
  598. nf_conntrack_rtsp v0.6.21 loading
  599. xt_time: kernel timezone is -0000
  600. ip_set: protocol 6
  601. gre: GRE over IPv4 demultiplexor driver
  602. nf_nat_rtsp v0.6.21 loading
  603. ip_tables: (C) 2000-2006 Netfilter Core Team
  604. TCP: bic registered
  605. TCP: cubic registered
  606. TCP: westwood registered
  607. TCP: highspeed registered
  608. TCP: hybla registered
  609. TCP: htcp registered
  610. TCP: vegas registered
  611. TCP: veno registered
  612. TCP: scalable registered
  613. TCP: lp registered
  614. TCP: yeah registered
  615. TCP: illinois registered
  616. NET: Registered protocol family 17
  617. Bridge firewalling registered
  618. 8021q: 802.1Q VLAN Support v1.8
  619. startup nvram driver
  620. found nvram
  621. List of all partitions:
  622. 1f00            1024 mtdblock0  (driver?)
  623. 1f01             256 mtdblock1  (driver?)
  624. 1f02           32768 mtdblock2  (driver?)
  625. 1f03           97280 mtdblock3  (driver?)
  626. 1f04           32768 mtdblock4  (driver?)
  627. 1f05           98304 mtdblock5  (driver?)
  628. No filesystem could mount root, tried:  squashfs
  629. Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5)
  630. Rebooting in 3 seconds..Please stand by while rebooting the system...
  631. cfe_led_init: start to set power LED and switch LEDs.
  632. Invalid command: "et"
  633. Available commands:



  634. Broadcom CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
  635. Build Date: Wed Jun 13 14:12:48 CST 2012 (lzh@team2compiler2)
  636. Copyright (C) 2000-2008 Broadcom Corporation.

  637. Init Arena
  638. Init Devs.
  639. This is a Serial Flash
  640. Boot partition size = 524288(0x80000)
  641. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  642. The NAND flash type is Samsung
  643. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  644. bcm_robo_enable_switch: EEE is disabled
  645. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.39.39.24
  646. CPU type 0x19749: 600MHz
  647. Tot mem: 131072 KBytes

  648. CFE mem:    0x80900000 - 0x80A67B40 (1473344)
  649. Data:       0x80951810 - 0x80954C90 (13440)
  650. BSS:        0x80954C90 - 0x80965B40 (69296)
  651. Heap:       0x80965B40 - 0x80A65B40 (1048576)
  652. Stack:      0x80A65B40 - 0x80A67B40 (8192)
  653. Text:       0x80900000 - 0x80951808 (333832)
  654. Boot:       0x00A68000 - 0x00AA8000
  655. Reloc:      I:00000000 - D:00000000

  656. Boot version: v0.1.8

  657. Device eth0:  hwaddr C8-D7-19-8B-AE-5D, ipaddr 192.168.1.1, mask 255.255.255.0
  658.         gateway not set, nameserver not set
  659. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
  660. Loading: Failed.
  661. Could not load :: Timeout occured
  662. boot wait load image command: load -raw -addr=0x80a67b40 -max=0x75984c0 :
  663. Changed to the other image 0 (maxpartialboots exceeded)
  664. Booting(0): boot -raw -z -addr=0x80001000 -max=0x8ff000 nflash0.os:
  665. Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
  666. Loading: ....... 5177478 bytes read
  667. Entry at 0x80001000
  668. Closing network.
  669. Starting program at 0x80001000
  670. Linux version 2.6.22 (root@hudson-node) (gcc version 4.2.3) #1 PREEMPT Fri Jan 18 02:31:09 PST 2013
  671. CPU revision is: 00019749
  672. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  673. Determined physical RAM map:
  674. memory: 07fff000 @ 00000000 (usable)
  675. Initrd not found or empty - disabling initrd
  676. Zone PFN ranges:
  677.   Normal          0 ->    32767
  678.   HighMem     32767 ->    32767
  679. early_node_map[1] active PFN ranges
  680.     0:        0 ->    32767
  681. Built 1 zonelists.  Total pages: 32767
  682. Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
  683. Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
  684. Primary data cache 32kB, 4-way, linesize 32 bytes.
  685. Synthesized TLB refill handler (20 instructions).
  686. Synthesized TLB load handler fastpath (32 instructions).
  687. Synthesized TLB store handler fastpath (32 instructions).
  688. Synthesized TLB modify handler fastpath (31 instructions).
  689. PID hash table entries: 512 (order: 9, 2048 bytes)
  690. CPU: BCM5300 rev 1 at 600 MHz
  691. Using 300.000 MHz high precision timer.
  692. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  693. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  694. Memory: 123776k/131068k available (3993k kernel code, 7144k reserved, 590k data, 472k init, 0k highmem)
  695. Mount-cache hash table entries: 512
  696. NET: Registered protocol family 16
  697. SCSI subsystem initialized
  698. PCI: Initializing host
  699. PCI: Reset RC
  700. PCI: Initializing host
  701. PCI: Reset RC
  702. PCI: Fixing up bus 0
  703. PCI/PCIe coreunit 0 is set to bus 1.
  704. PCI: Fixing up bridge
  705. PCI: Fixing up bridge
  706. PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
  707. PCI: Fixing up bus 1
  708. PCI/PCIe coreunit 1 is set to bus 2.
  709. PCI: Fixing up bridge
  710. PCI: Fixing up bridge
  711. PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
  712. PCI: Fixing up bus 2
  713. NET: Registered protocol family 2
  714. Time: MIPS clocksource has been installed.
  715. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  716. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  717. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
  718. TCP: Hash tables configured (established 4096 bind 4096)
  719. TCP reno registered
  720. VFS: Disk quotas dquot_6.5.1
  721. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  722. squashfs: version 3.4 (2008/08/26) Phillip Lougher
  723. NTFS driver 2.1.28 [Flags: R/W].
  724. JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
  725. fuse init (API version 7.8)
  726. io scheduler noop registered (default)
  727. HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
  728. N_HDLC line discipline registered.
  729. Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
  730. serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
  731. serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
  732. RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
  733. loop: module loaded
  734. PPP generic driver version 2.4.2
  735. PPP MPPE Compression module registered
  736. NET: Registered protocol family 24
  737. SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
  738. pflash: found no supported devices
  739. The first offset=0, 2nd offset=2000000
  740. Boot partition size = 524288(0x80000)
  741. Creating 2 MTD partitions on "sflash":
  742. 0x00000000-0x00080000 : "boot"
  743. 0x000c0000-0x00100000 : "nvram"
  744. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  745. The first offset=0, 2nd offset=2000000
  746. lookup_nflash_rootfs_offset: offset = 0x0
  747. nflash: squash filesystem with lzma found at block 16
  748. lookup_nflash_rootfs_offset: offset = 0x2000000
  749. Creating 4 MTD partitions on "nflash":
  750. 0x00000000-0x02000000 : "linux"
  751. 0x0020b6a0-0x02000000 : "rootfs"
  752. 0x02000000-0x04000000 : "linux2"
  753. 0x0400d400-0x04000000 : "rootfs2"
  754. NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
  755. The first offset=0, 2nd offset=2000000
  756. Creating 1 MTD partitions on "brcmnand":
  757. 0x04000000-0x07f00000 : "syscfg"
  758. u32 classifier
  759.     Actions configured
  760. Netfilter messages via NETLINK v0.30.
  761. nf_conntrack version 0.5.0 (1023 buckets, 8184 max)
  762. ctnetlink v0.93: registering with nfnetlink.
  763. nf_conntrack_rtsp v0.6.21 loading
  764. IPv4 over IPv4 tunneling driver
  765. nf_nat_rtsp v0.6.21 loading
  766. ip_tables: (C) 2000-2006 Netfilter Core Team
  767. TCP cubic registered
  768. NET: Registered protocol family 1
  769. NET: Registered protocol family 10
  770. ip6_tables: (C) 2000-2006 Netfilter Core Team
  771. IPv6 over IPv4 tunneling driver
  772. NET: Registered protocol family 17
  773. Bridge firewalling registered
  774. Ebtables v2.0 registered
  775. ebt_ulog: not logging via ulog since somebody else already registered for PF_BRIDGE
  776. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  777. All bugs added by David S. Miller <davem@redhat.com>
  778. VFS: Mounted root (squashfs filesystem) readonly.
  779. Freeing unused kernel memory: 472k freed
  780. Failed to execute /init
  781. Failed to execute /sbin/preinit.  Attempting defaults...
  782. Algorithmics/MIPS FPU Emulator v1.5
  783. *******************************************************************

  784.                    |           |
  785.                  .|||.       .|||.
  786.              ..:|||||||:...:|||||||:..
  787.              C i s c o   S y s t e m s

  788.    Copyright (c) 2011 by Cisco Systems, Inc. All Rights Reserved.   
  789.    Booting carrera (firmware version 1.1.28.147876)
  790. *******************************************************************
  791. [utopia][init] System Initialization
  792. [utopia][init] Starting udev..
  793. bdutil board utility kernel module, version 1.3
  794. bdutil board utility kernel module boardId (1)
  795. bdutil board utility buttons kernel module, version 1.3
  796. bdutil board utility LEDs kernel module, version 1.3
  797. bdutil board utility usbhub kernel module, version 1.1
  798. chmod: /tmp/etc/.root/passwd: No such file or directory
  799. chmod: /tmp/etc/.root/shadow: No such file or directory
  800. chmod: /tmp/etc/.root/group: No such file or directory
  801. [utopia][init] Using persistent syscfg data from /var/config/syscfg
  802. [utopia][init] Starting system logging
  803. [utopia][init] Starting sysevent subsystem
  804. [utopia][init] Setting any unset system values to default
  805. [utopia][init] Late loading usb drivers
  806. inserting ctf.ko
  807. mount: mounting /tmp/backup on /www/backup failed: No such file or directory
  808. 0xb000000 0x1000000
  809. system_state-normal|/etc/led/solid.sh ; system_state-error|/etc/led/blink_15_sec.sh ; system_state-heartbeat|/etc/led/pulsate.sh ; fwupd-start|/etc/led/pulsate.sh ; fwupd-success|/etc/led/solid.sh ; fwupd-failed|/etc/led/blink_15_sec.sh ; wps-running|/etc/led/pulsate_wps.sh ; wps-success|/etc/led/solid.sh ; wps-failed|/etc/led/blink_15_sec.sh ; wps-stopped|/etc/led/solid.sh ; led_ethernet_on|/etc/led/rear_all_default.sh ; led_ethernet_off|/etc/led/rear_all_off.sh ;\
  810. 0xc000000 0x1000000
  811. 0xd000000 0x1000000
  812. 0xe000000 0x1000000
  813. 0xf000000 0x1000000
  814. 0x10000000 0x1000000
  815. 0x11000000 0x1000000
  816. 0x12000000 0x1000000
  817. 0x13000000 0x1000000
  818. 0x14000000 0x1000000
  819. 0x15000000 0x1000000
  820. 0x16000000 0x1000000
  821. 0x17000000 0x1000000
  822. 0x18000000 0x1000000
  823. file sharing waiting for lan startup
  824. Cannot find downloads MTD partition, /dev/
  825. [utopia][init] Starting bdutil daemon
  826. BDUTIL daemon mode
  827. Sat Jul 28 17:10:00 UTC 2012

  828. (none) login: configuring interfaces for IGMP filtering
  829. Lighttpd Model Base: EA6500
  830. Generating Rainier lighttpd config
  831. insmod: can't insert '/lib/modules/2.6.22//usbcore.ko': File exists
  832. insmod: can't insert '/lib/modules/2.6.22//ehci-hcd.ko': File exists
  833. Build temporary www configuration directory:
  834. TSLIIHauhEfGE
  835. Registering Service myrouter._http._tcp.local port 80
  836. Got a reply for myrouter._http._tcp.local.: Name now registered and active
  837. ls: /tmp/anon_smb/: No such file or directory
  838. Duplicate configuration request

  839. Device is Broadcom Router
  840. Setting regioncode Q2/13 to eth1
  841. Failed to modify password entry for user guest
  842. Chanspec set to 0xd0a5
  843. killall: nmbd: no process killed
  844. ls: /mnt/: No such file or directory
  845. ls: /mnt/: No such file or directory
  846. find: /mnt/: No such file or directory
  847. find: /mnt/: No such file or directory
  848. find: /mnt/: No such file or directory
  849. total smb count 0
  850. total ftp count 0
  851. total med count 0
  852. ls: /mnt/: No such file or directory
  853. ls: /mnt/: No such file or directory
  854. find: /mnt/: No such file or directory
  855. find: /mnt/: No such file or directory
  856. find: /mnt/: No such file or directory
  857. total smb count 0
  858. total ftp count 0
  859. total med count 0
  860. file_sharing waiting a while for system resources before starting
  861. Setting regioncode Q2/13 to eth2
  862. Chanspec set to 0x1909
  863. Restarting nfqrecv service...
  864. ls: /tmp/anon_smb/: No such file or directory
  865. eth2: WLC_GET_VAR(psta_if): Operation not supported
  866. eth1: WLC_GET_VAR(psta_if): Operation not supported
  867. wl1.2: WLC_GET_VAR(psta_if): Operation not supported
  868. eth2: WLC_GET_VAR(psta_if): Operation not supported
  869. eth1: WLC_GET_VAR(psta_if): Operation not supported
  870. Failed to modify password entry for user guest
  871. Starting smbd ...
  872. eth2: WLC_GET_VAR(psta_if): Operation not supported
  873. eth2: WLC_GET_VAR(psta_if): Operation not supported

  874. ### wps_wfi_init(): eth1: WLC_GET_VAR(psta_if): Operation not supported
  875. <wl0_wfi_enable=(null)><wl1_wfi_enable=(null)><wl1.2_wfi_enable=(null)><wl1.1_wfi_enable=(null)>WFI is not enabled ###
  876. eth1: WLC_GET_VAR(psta_if): Operation not supported
  877. eth2: WLC_GET_VAR(psta_if): Operation not supported
  878. eth2: WLC_GET_VAR(psta_if): Operation not supported
  879. eth2: WLC_GET_VAR(psta_if): Operation not supported
  880. eth2: WLC_GET_VAR(psta_if): Operation not supported
  881. Oops[#1]:
  882. Cpu 0
  883. $ 0   : 00000000 1100fc00 a8008000 04160403
  884. $ 4   : 80784000 86064980 ffffb1c6 ffffb163
  885. $ 8   : 87fcbfe0 0000fc00 00000000 80458000
  886. $12   : fd5cd500 00000016 23f81d00 00989651
  887. $16   : 87c5d780 86069800 87c5d798 804f5780
  888. $20   : efffffff 804f5780 80400000 80400000
  889. $24   : 00000000 c06eed28                  
  890. $28   : 87fca000 87fcbea0 00000000 c06eed74
  891. Hi    : 00001900
  892. Lo    : 000015e0
  893. epc   : c0736f98     Tainted: P      
  894. ra    : c06eed74 Status: 1100fc03    KERNEL EXL IE
  895. Cause : 0000001c
  896. PrId  : 00019749
  897. Modules linked in: nf_nat_ftp nf_conntrack_ftp libusual ehci_hcd usbcore wl(P) igs(P) emf(P) et(P) bcm57xx ctf(P) mod_bdutil
  898. Process events/0 (pid: 4, threadinfo=87fca000, task=87fc0ce0)
  899. Stack : 87fc0ce0 00000000 00000000 00000000 86064980 86064980 c06eed74 20000000
  900.         c0100000 00000001 804fbce0 804fbc18 1100fc01 c0773ec0 87c5d780 86064980
  901.         87c5d780 86064980 87c5d798 c06ce7c4 800282a8 8606a340 804f5780 c07634a0
  902.         86064980 86719980 87ffd600 c06ce860 c06ce888 c06ce8a4 805090b4 805090b0
  903.         00000000 87fc0e20 86719984 86719980 80049ed4 80049ed4 00000000 c06f2908
  904.         ...
  905. Call Trace:[<c06eed74>][<c0773ec0>][<c06ce7c4>][<800282a8>][<c07634a0>][<c06ce860>][<c06ce888>][<c06ce8a4>][<80049ed4>][<80049ed4>][<c06f2908>][<8004afc4>][<8004af74>][<8004afc4>][<800501e8>][<80050588>][<8004aec4>][<8005022c>][<8000e5c0>][<8000e5b0>]

  906. Code: 0000000f  8c820084  8c430120 <afa30010> 0000000f  8fa20010  8fbf0018  30420404  38420400
  907. Fatal exception: panic in 5 seconds
  908. Kernel panic - not syncing: Fatal exception
  909. Rebooting in 3 seconds..Please stand by while rebooting the system...
  910. cfe_led_init: start to set power LED and switch LEDs.
  911. Invalid command: "et"
  912. Available commands:



  913. Broadcom CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
  914. Build Date: Wed Jun 13 14:12:48 CST 2012 (lzh@team2compiler2)
  915. Copyright (C) 2000-2008 Broadcom Corporation.

  916. Init Arena
  917. Init Devs.
  918. This is a Serial Flash
  919. Boot partition size = 524288(0x80000)
  920. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  921. The NAND flash type is Samsung
  922. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  923. bcm_robo_enable_switch: EEE is disabled
  924. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.39.39.24
  925. CPU type 0x19749: 600MHz
  926. Tot mem: 131072 KBytes

  927. CFE mem:    0x80900000 - 0x80A67B40 (1473344)
  928. Data:       0x80951810 - 0x80954C90 (13440)
  929. BSS:        0x80954C90 - 0x80965B40 (69296)
  930. Heap:       0x80965B40 - 0x80A65B40 (1048576)
  931. Stack:      0x80A65B40 - 0x80A67B40 (8192)
  932. Text:       0x80900000 - 0x80951808 (333832)
  933. Boot:       0x00A68000 - 0x00AA8000
  934. Reloc:      I:00000000 - D:00000000

  935. Boot version: v0.1.8

  936. Device eth0:  hwaddr C8-D7-19-8B-AE-5D, ipaddr 192.168.1.1, mask 255.255.255.0
  937.         gateway not set, nameserver not set
  938. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
  939. Loading: Failed.
  940. Could not load :: Timeout occured
  941. boot wait load image command: load -raw -addr=0x80a67b40 -max=0x75984c0 :
  942. Booting(0): boot -raw -z -addr=0x80001000 -max=0x8ff000 nflash0.os:
  943. Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
  944. Loading: ....... 5177478 bytes read
  945. Entry at 0x80001000
  946. Closing network.
  947. Starting program at 0x80001000
  948. Linux version 2.6.22 (root@hudson-node) (gcc version 4.2.3) #1 PREEMPT Fri Jan 18 02:31:09 PST 2013
  949. CPU revision is: 00019749
  950. Found an ST compatible serial flash with 256 4KB blocks; total size 1MB
  951. Determined physical RAM map:
  952. memory: 07fff000 @ 00000000 (usable)
  953. Initrd not found or empty - disabling initrd
  954. Zone PFN ranges:
  955.   Normal          0 ->    32767
  956.   HighMem     32767 ->    32767
  957. early_node_map[1] active PFN ranges
  958.     0:        0 ->    32767
  959. Built 1 zonelists.  Total pages: 32767
  960. Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
  961. Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
  962. Primary data cache 32kB, 4-way, linesize 32 bytes.
  963. Synthesized TLB refill handler (20 instructions).
  964. Synthesized TLB load handler fastpath (32 instructions).
  965. Synthesized TLB store handler fastpath (32 instructions).
  966. Synthesized TLB modify handler fastpath (31 instructions).
  967. PID hash table entries: 512 (order: 9, 2048 bytes)
  968. CPU: BCM5300 rev 1 at 600 MHz
  969. Using 300.000 MHz high precision timer.
  970. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  971. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  972. Memory: 123776k/131068k available (3993k kernel code, 7144k reserved, 590k data, 472k init, 0k highmem)
  973. Mount-cache hash table entries: 512
  974. NET: Registered protocol family 16
  975. SCSI subsystem initialized
  976. PCI: Initializing host
  977. PCI: Reset RC
  978. PCI: Initializing host
  979. PCI: Reset RC
  980. PCI: Fixing up bus 0
  981. PCI/PCIe coreunit 0 is set to bus 1.
  982. PCI: Fixing up bridge
  983. PCI: Fixing up bridge
  984. PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
  985. PCI: Fixing up bus 1
  986. PCI/PCIe coreunit 1 is set to bus 2.
  987. PCI: Fixing up bridge
  988. PCI: Fixing up bridge
  989. PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
  990. PCI: Fixing up bus 2
  991. NET: Registered protocol family 2
  992. Time: MIPS clocksource has been installed.
  993. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  994. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
  995. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
  996. TCP: Hash tables configured (established 4096 bind 4096)
  997. TCP reno registered
  998. VFS: Disk quotas dquot_6.5.1
  999. Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  1000. squashfs: version 3.4 (2008/08/26) Phillip Lougher
  1001. NTFS driver 2.1.28 [Flags: R/W].
  1002. JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
  1003. fuse init (API version 7.8)
  1004. io scheduler noop registered (default)
  1005. HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
  1006. N_HDLC line discipline registered.
  1007. Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
  1008. serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
  1009. serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
  1010. RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
  1011. loop: module loaded
  1012. PPP generic driver version 2.4.2
  1013. PPP MPPE Compression module registered
  1014. NET: Registered protocol family 24
  1015. SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
  1016. pflash: found no supported devices
  1017. The first offset=0, 2nd offset=2000000
  1018. Boot partition size = 524288(0x80000)
  1019. Creating 2 MTD partitions on "sflash":
  1020. 0x00000000-0x00080000 : "boot"
  1021. 0x000c0000-0x00100000 : "nvram"
  1022. Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
  1023. The first offset=0, 2nd offset=2000000
  1024. lookup_nflash_rootfs_offset: offset = 0x0
  1025. nflash: squash filesystem with lzma found at block 16
  1026. lookup_nflash_rootfs_offset: offset = 0x2000000
  1027. Creating 4 MTD partitions on "nflash":
  1028. 0x00000000-0x02000000 : "linux"
  1029. 0x0020b6a0-0x02000000 : "rootfs"
  1030. 0x02000000-0x04000000 : "linux2"
  1031. 0x0400d400-0x04000000 : "rootfs2"
  1032. NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
  1033. The first offset=0, 2nd offset=2000000
  1034. Creating 1 MTD partitions on "brcmnand":
  1035. 0x04000000-0x07f00000 : "syscfg"
  1036. u32 classifier
  1037.     Actions configured
  1038. Netfilter messages via NETLINK v0.30.
  1039. nf_conntrack version 0.5.0 (1023 buckets, 8184 max)
  1040. ctnetlink v0.93: registering with nfnetlink.
  1041. nf_conntrack_rtsp v0.6.21 loading
  1042. IPv4 over IPv4 tunneling driver
  1043. nf_nat_rtsp v0.6.21 loading
  1044. ip_tables: (C) 2000-2006 Netfilter Core Team
  1045. TCP cubic registered
  1046. NET: Registered protocol family 1
  1047. NET: Registered protocol family 10
  1048. ip6_tables: (C) 2000-2006 Netfilter Core Team
  1049. IPv6 over IPv4 tunneling driver
  1050. NET: Registered protocol family 17
  1051. Bridge firewalling registered
  1052. Ebtables v2.0 registered
  1053. ebt_ulog: not logging via ulog since somebody else already registered for PF_BRIDGE
  1054. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  1055. All bugs added by David S. Miller <davem@redhat.com>
  1056. VFS: Mounted root (squashfs filesystem) readonly.
  1057. Freeing unused kernel memory: 472k freed
  1058. Failed to execute /init
  1059. Failed to execute /sbin/preinit.  Attempting defaults...
  1060. Algorithmics/MIPS FPU Emulator v1.5
  1061. *******************************************************************

  1062.                    |           |
  1063.                  .|||.       .|||.
  1064.              ..:|||||||:...:|||||||:..
  1065.              C i s c o   S y s t e m s

  1066.    Copyright (c) 2011 by Cisco Systems, Inc. All Rights Reserved.   
  1067.    Booting carrera (firmware version 1.1.28.147876)
  1068. *******************************************************************
  1069. [utopia][init] System Initialization
  1070. [utopia][init] Starting udev..
  1071. bdutil board utility kernel module, version 1.3
  1072. bdutil board utility kernel module boardId (1)
  1073. bdutil board utility buttons kernel module, version 1.3
  1074. bdutil board utility LEDs kernel module, version 1.3
  1075. bdutil board utility usbhub kernel module, version 1.1
  1076. chmod: /tmp/etc/.root/passwd: No such file or directory
  1077. chmod: /tmp/etc/.root/shadow: No such file or directory
  1078. chmod: /tmp/etc/.root/group: No such file or directory
  1079. [utopia][init] Using persistent syscfg data from /var/config/syscfg
  1080. [utopia][init] Starting system logging
  1081. [utopia][init] Starting sysevent subsystem
  1082. [utopia][init] Setting any unset system values to default
  1083. [utopia][init] Late loading usb drivers
  1084. inserting ctf.ko
  1085. mount: mounting /tmp/backup on /www/backup failed: No such file or directory
  1086. 0xb000000 0x1000000
  1087. system_state-normal|/etc/led/solid.sh ; system_state-error|/etc/led/blink_15_sec.sh ; system_state-heartbeat|/etc/led/pulsate.sh ; fwupd-start|/etc/led/pulsate.sh ; fwupd-success|/etc/led/solid.sh ; fwupd-failed|/etc/led/blink_15_sec.sh ; wps-running|/etc/led/pulsate_wps.sh ; wps-success|/etc/led/solid.sh ; wps-failed|/etc/led/blink_15_sec.sh ; wps-stopped|/etc/led/solid.sh ; led_ethernet_on|/etc/led/rear_all_default.sh ; led_ethernet_off|/etc/led/rear_all_off.sh ;\
  1088. 0xc000000 0x1000000
  1089. 0xd000000 0x1000000
  1090. 0xe000000 0x1000000
  1091. 0xf000000 0x1000000
  1092. 0x10000000 0x1000000
  1093. 0x11000000 0x1000000
  1094. 0x12000000 0x1000000
  1095. 0x13000000 0x1000000
  1096. 0x14000000 0x1000000
  1097. 0x15000000 0x1000000
  1098. 0x16000000 0x1000000
  1099. 0x17000000 0x1000000
  1100. 0x18000000 0x1000000
  1101. file sharing waiting for lan startup
  1102. Cannot find downloads MTD partition, /dev/
  1103. [utopia][init] Starting bdutil daemon
  1104. BDUTIL daemon mode
  1105. Sat Jul 28 17:10:00 UTC 2012

  1106. (none) login: configuring interfaces for IGMP filtering
  1107. Lighttpd Model Base: EA6500
  1108. Generating Rainier lighttpd config
  1109. insmod: can't insert '/lib/modules/2.6.22//usbcore.ko': File exists
  1110. insmod: can't insert '/lib/modules/2.6.22//ehci-hcd.ko': File exists
  1111. Build temporary www configuration directory:
  1112. TSLIIHauhEfGE
  1113. Registering Service myrouter._http._tcp.local port 80
  1114. Got a reply for myrouter._http._tcp.local.: Name now registered and active
  1115. ls: /tmp/anon_smb/: No such file or directory
  1116. Duplicate configuration request

  1117. Device is Broadcom Router
  1118. Setting regioncode Q2/13 to eth1
  1119. Chanspec set to 0xd0a5
  1120. Failed to modify password entry for user guest
  1121. killall: nmbd: no process killed
  1122. ls: /mnt/: No such file or directory
  1123. ls: /mnt/: No such file or directory
  1124. find: /mnt/: No such file or directory
  1125. find: /mnt/: No such file or directory
  1126. find: /mnt/: No such file or directory
  1127. total smb count 0
  1128. total ftp count 0
  1129. total med count 0
  1130. ls: /mnt/: No such file or directory
  1131. ls: /mnt/: No such file or directory
  1132. find: /mnt/: No such file or directory
  1133. find: /mnt/: No such file or directory
  1134. find: /mnt/: No such file or directory
  1135. total smb count 0
  1136. total ftp count 0
  1137. total med count 0
  1138. file_sharing waiting a while for system resources before starting
  1139. Setting regioncode Q2/13 to eth2
  1140. Chanspec set to 0x1909
复制代码
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2013-12-7 17:39 | 显示全部楼层
222ba 发表于 2013-12-7 16:49
我来测试。。稍后给答复

来了,变砖了、

看日志,固件没有刷进去。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 17:44 | 显示全部楼层
哎。郁闷加班中无法回去测试,看222ba的测试估计又要TFTP刷了,或者要降为上版固件刷
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2013-12-7 17:56 | 显示全部楼层
zangma0427 发表于 2013-12-7 17:44
哎。郁闷加班中无法回去测试,看222ba的测试估计又要TFTP刷了,或者要降为上版固件刷

先用tftp刷试试看,能刷进去的话,一般应该能起来
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2013-12-7 18:07 | 显示全部楼层
从DD论坛看,现在还没有一个稳定的DD版本能刷EA6500 v1.

http://www.dd-wrt.com/forum/view ... r=asc&start=330

===================================
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1057

PostPosted: Sat Nov 30, 2013 16:59    Post subject:        Reply with quote
I only post builds I personally test, these AC units are not cheap and bricking them is not fun... That being said I can vouch for KONG as his latest build DOES work on the D1800h and the AC66u as far as non arm devices go...

It does not work on the EA6500.. I have tested nightly builds and can confirm that they brick this device this means brains Slayers, KONGS, and my own, that is why I have not released any new builds for the EA6500. This is not KONGs fault!

I will work with kong on fixing this, I am getting section 8 kernel panics which is what is causing the boot loop.

I am going to try and get my hands on the EA6900 device today to help get dd-wrt support for it.

looked at specs:
EA6700 - 1ghz cpu 128mb ram
ea6900 - 800mhz cpu 256mb ram

choices lol.

-Fractal
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 18:19 | 显示全部楼层
bwq518 发表于 2013-12-7 18:07
从DD论坛看,现在还没有一个稳定的DD版本能刷EA6500 v1.

http://www.dd-wrt.com/forum/viewtopic.php?t= ...

版主 我的EA6500刷了DDWRT固话  
可以再刷TT固件不?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 19:06 | 显示全部楼层
banzhu我手里有EA6500 加我QQ1900794 细聊
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 22:04 | 显示全部楼层
支持并关注此贴,加油
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2013-12-7 22:08 | 显示全部楼层
手持6700,坐等适配~

点评

把6700 CFE发给版主啊  发表于 2013-12-8 10:15
既然有 就帮着版主 提供 CFE 等个P啊  发表于 2013-12-7 22:09
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 19:28

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表