|
|
本帖最后由 djsht 于 2014-2-25 16:31 编辑
[ 0.000000] Linux version 3.3.8 (haxc@haxc--pc) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #19 Thu Sep 26 17:42:30 CST 2013
[ 0.000000] MyLoader: sysp=a54f88e8, boardp=64a94a2f, parts=cd192863
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9341 rev 1
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802e6270, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR841N-v8 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61532k/65536k available (2173k kernel code, 4004k reserved, 412k data, 212k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR841N/ND v8
[ 0.510000] kobject (802d3ea0): tried to init an initialized object, something is seriously wrong.
[ 0.520000] Call Trace:[<8007c870>] 0x8007c870
[ 0.520000] [<8027a990>] 0x8027a990
[ 0.520000] [<8027a990>] 0x8027a990
[ 0.530000] [<80166c10>] 0x80166c10
[ 0.530000] [<802e9840>] 0x802e9840
[ 0.530000] [<801ab748>] 0x801ab748
[ 0.530000] [<801b01f4>] 0x801b01f4
[ 0.540000] [<802ec10c>] 0x802ec10c
[ 0.540000] [<801aff9c>] 0x801aff9c
[ 0.540000] [<802eb930>] 0x802eb930
[ 0.540000] [<802e9840>] 0x802e9840
[ 0.550000] [<802f036c>] 0x802f036c
[ 0.550000] [<802e9868>] 0x802e9868
[ 0.550000] [<80060900>] 0x80060900
[ 0.550000] [<802e797c>] 0x802e797c
[ 0.560000] [<80064b70>] 0x80064b70
[ 0.560000] [<802e78d0>] 0x802e78d0
[ 0.560000] [<80064b60>] 0x80064b60
[ 0.560000]
[ 0.570000] ------------[ cut here ]------------
[ 0.570000] WARNING: at kernel/resource.c:597 0x800817d0()
[ 0.570000] Modules linked in:
[ 0.580000] Call Trace:[<8027a990>] 0x8027a990
[ 0.580000] [<8027a990>] 0x8027a990
[ 0.580000] [<8007b8ac>] 0x8007b8ac
[ 0.590000] [<800817d0>] 0x800817d0
[ 0.590000] [<8007b8f0>] 0x8007b8f0
[ 0.590000] [<80167320>] 0x80167320
[ 0.590000] [<800817d0>] 0x800817d0
[ 0.600000] [<802e9840>] 0x802e9840
[ 0.600000] [<800822b4>] 0x800822b4
[ 0.600000] [<802e9840>] 0x802e9840
[ 0.600000] [<801aff54>] 0x801aff54
[ 0.610000] [<802e9840>] 0x802e9840
[ 0.610000] [<802ec10c>] 0x802ec10c
[ 0.610000] [<801aff9c>] 0x801aff9c
[ 0.610000] [<802eb930>] 0x802eb930
[ 0.620000] [<802e9840>] 0x802e9840
[ 0.620000] [<802f036c>] 0x802f036c
[ 0.620000] [<802e9868>] 0x802e9868
[ 0.620000] [<80060900>] 0x80060900
[ 0.630000] [<802e797c>] 0x802e797c
[ 0.630000] [<80064b70>] 0x80064b70
[ 0.630000] [<802e78d0>] 0x802e78d0
[ 0.630000] [<80064b60>] 0x80064b60
[ 0.640000]
[ 0.640000] ---[ end trace ff8f13a0cc5d8ccb ]---
[ 0.640000] ehci-platform: failed to claim resource 0
[ 0.650000] bio: create slab <bio-0> at 0
[ 0.660000] Switching to clocksource MIPS
[ 0.670000] NET: Registered protocol family 2
[ 0.670000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.670000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.680000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.680000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.690000] TCP reno registered
[ 0.690000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.700000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.700000] NET: Registered protocol family 1
[ 0.710000] PCI: CLS 0 bytes, default 32
[ 0.720000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.730000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.740000] msgmni has been set to 120
[ 0.740000] io scheduler noop registered
[ 0.750000] io scheduler deadline registered (default)
[ 0.750000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.780000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.790000] console [ttyS0] enabled, bootconsole disabled
[ 0.800000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.810000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.810000] 6 tp-link partitions found on MTD device spi0.0
[ 0.820000] Creating 6 MTD partitions on "spi0.0":
[ 0.820000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.830000] 0x000000020000-0x000000106dc8 : "kernel"
[ 0.840000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.850000] 0x000000106dc8-0x0000007f0000 : "rootfs"
[ 0.860000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.870000] mtd: partition "rootfs" set to be root filesystem
[ 0.880000] mtd: partition "rootfs_data" created automatically, ofs=760000, len=90000
[ 0.890000] 0x000000760000-0x0000007f0000 : "rootfs_data"
[ 0.890000] 0x0000007f0000-0x000000800000 : "art"
[ 0.900000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.910000] 0x000000000000-0x000000800000 : "fullflash"
[ 0.930000] ag71xx_mdio: probed
[ 0.940000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.490000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 1.500000] eth1: Atheros AG71xx at 0xba000000, irq 5
[ 2.060000] eth1: Found an AR934X built-in switch
[ 3.100000] TCP cubic registered
[ 3.100000] NET: Registered protocol family 17
[ 3.100000] 8021q: 802.1Q VLAN Support v1.8
[ 3.120000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 3.120000] Freeing unused kernel memory: 212k freed
[ 6.200000] Registered led device: tp-link:green:lan1
[ 6.200000] Registered led device: tp-link:green:lan2
[ 6.200000] Registered led device: tp-link:green:lan3
[ 6.200000] Registered led device: tp-link:green:lan4
[ 6.200000] Registered led device: tp-link:green:qss
[ 6.200000] Registered led device: tp-link:green:system
[ 6.200000] Registered led device: tp-link:green:wan
[ 6.210000] Registered led device: tp-link:green:wlan
[ 9.550000] JFFS2 notice: (425) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 25 of xref (0 dead, 2 orphan) found.
[ 10.440000] SCSI subsystem initialized
[ 10.640000] usbcore: registered new interface driver usbfs
[ 10.640000] usbcore: registered new interface driver hub
[ 10.650000] usbcore: registered new device driver usb
[ 11.120000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.200000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 11.290000] uhci_hcd: USB Universal Host Controller Interface driver
[ 11.390000] Initializing USB Mass Storage driver...
[ 11.390000] usbcore: registered new interface driver usb-storage
[ 11.400000] USB Mass Storage support registered.
[ 33.870000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 33.880000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 34.090000] cfg80211: Calling CRDA to update world regulatory domain
[ 34.090000] cfg80211: World regulatory domain updated:
[ 34.100000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 34.110000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 34.120000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 34.120000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 34.130000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 34.140000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 35.370000] ath: EEPROM regdomain: 0x0
[ 35.370000] ath: EEPROM indicates default country code should be used
[ 35.370000] ath: doing EEPROM country->regdmn map search
[ 35.370000] ath: country maps to regdmn code: 0x3a
[ 35.370000] ath: Country alpha2 being used: US
[ 35.370000] ath: Regpair used: 0x3a
[ 35.370000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 35.380000] Registered led device: ath9k-phy0
[ 35.380000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 35.380000] cfg80211: Calling CRDA for country: US
[ 35.390000] cfg80211: Regulatory domain changed to country: US
[ 35.400000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 35.400000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 35.410000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 35.420000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 35.430000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 35.440000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 35.440000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 36.010000] PPP generic driver version 2.4.2
[ 36.370000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 36.560000] NET: Registered protocol family 24
[ 36.610000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
[ 37.370000] xt_time: kernel timezone is -0000
[ 38.100000] usbcore: registered new interface driver ath9k_htc
[ 38.280000] usbcore: registered new interface driver usblp
[ 38.310000] usbcore: registered new interface driver usbserial
[ 38.310000] USB Serial support registered for generic
[ 38.320000] usbcore: registered new interface driver usbserial_generic
[ 38.330000] usbserial: USB Serial Driver core
[ 38.450000] usbcore: registered new interface driver ums-alauda
[ 38.470000] usbcore: registered new interface driver ums-cypress
[ 38.490000] usbcore: registered new interface driver ums-datafab
[ 38.510000] usbcore: registered new interface driver ums-freecom
[ 38.540000] usbcore: registered new interface driver ums-isd200
[ 38.560000] usbcore: registered new interface driver ums-jumpshot
[ 38.580000] usbcore: registered new interface driver ums-karma
[ 38.600000] usbcore: registered new interface driver ums-sddr09
[ 38.700000] usbcore: registered new interface driver ums-sddr55
[ 38.720000] usbcore: registered new interface driver ums-usbat
[ 38.920000] USB Serial support registered for ch341-uart
[ 38.920000] usbcore: registered new interface driver ch341
[ 38.950000] USB Serial support registered for FTDI USB Serial Device
[ 38.960000] usbcore: registered new interface driver ftdi_sio
[ 38.960000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[ 39.050000] USB Serial support registered for pl2303
[ 39.050000] usbcore: registered new interface driver pl2303
[ 39.060000] pl2303: Prolific PL2303 USB to serial adaptor driver
[ 39.150000] usbcore: registered new interface driver usbhid
[ 39.160000] usbhid: USB HID core driver
[ 39.250000] fuse init (API version 7.18)
[ 45.700000] device eth1 entered promiscuous mode
[ 46.300000] eth1: link up (1000Mbps/Full duplex)
[ 46.300000] br-lan: port 1(eth1) entered forwarding state
[ 46.310000] br-lan: port 1(eth1) entered forwarding state
[ 48.310000] br-lan: port 1(eth1) entered forwarding state
[ 51.410000] device wlan0 entered promiscuous mode
[ 51.460000] br-lan: port 2(wlan0) entered forwarding state
[ 51.460000] br-lan: port 2(wlan0) entered forwarding state
[ 53.460000] br-lan: port 2(wlan0) entered forwarding state
附件大无法上传 附转载地址https://www.right.com.cn/forum/forum.php?mod=viewthread&tid=114913
|
|
/2 
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2014-2-25 16:30
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
肯定不是线的问题
