【首发】【更新】全民玩华硕~BCM4708以上全系列支持华硕啦~腾达屌丝机立马变高...

yech163

kesunji 发表于 2015-5-6 13:12
问题版主说他暂时没空搞啊，其实我就是需要华硕里面的无线助手功能，而且华硕的固件可以让小米路由多一个 ...

要是你不需要5G 可以去买个fh451来改啊 这个也不错

唯美的风景

kesunji 发表于 2015-5-6 13:12
问题版主说他暂时没空搞啊，其实我就是需要华硕里面的无线助手功能，而且华硕的固件可以让小米路由多一个 ...

这个把telnet开起来，看下ifconfig无线有没有认到呢
按理说2.4G是没问题的BCM的一个驱动能吃全家的无线，并且差异不是大。
F451无线是4331的,N18u是4360的，一样能用啊

kesunji

yech163 发表于 2015-5-7 01:33
要是你不需要5G 可以去买个fh451来改啊 这个也不错

我已经翻出了存放已久的N60，刷上了华硕N15U固件，只是可惜5G驱动不了，刷了N53U，千兆又驱动不了，郁闷。千兆、双频、和华硕不可兼得啊。

zlxq0517

支持LZ。顺便问问大家。博通有去广告的插件吗？

kesunji

唯美的风景 发表于 2015-5-7 08:58
这个把telnet开起来，看下ifconfig无线有没有认到呢
按理说2.4G是没问题的BCM的一个驱动能吃全家的无线 ...

设备应该是认到了但是配上参数后就是没信号出来。对了，之前忘了说，USB也不工作，下面是Log

ASUSWRT RT-N18U_3.0.0.4 Sun Mar 15 06:04:58 UTC 2015
admin@(none):/tmp/home/root# dmesg
Linux version 2.6.36.4brcmarm (root@onion-machine) (gcc version 4.5.3 (Buildroot 2012.02) ) #1 PREEMPT Sun Mar 15 12:07:11 CST 2015
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Northstar Prototype
Ignoring unrecognised tag 0x00000000
bootconsole [earlycon0] enabled
Memory policy: ECC disabled, Data cache writeback
MPCORE found at 19020000
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat c03c8094, node_mem_map c0407000
  Normal zone: 256 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 32512 pages, LIFO batch:7
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit earlyprintk debug
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125820k/125820k available, 5252k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xf7e00000 - 0xffe00000   ( 128 MB)
    vmalloc : 0xc8800000 - 0xf0000000   ( 632 MB)
    lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .init : 0xc0008000 - 0xc0036000   ( 184 kB)
      .text : 0xc0036000 - 0xc0393000   (3444 kB)
      .data : 0xc03aa000 - 0xc03c9780   ( 126 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
        RCU-based detection of stalled CPUs is disabled.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:256
MPCORE GIC init
MPCORE Global Timer Clock 400000000Hz
Calibrating delay loop... 1599.07 BogoMIPS (lpj=7995392)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
L310: cache controller enabled 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7a130000
devtmpfs: initialized
atomic64 test passed
NET: Registered protocol family 16
--------------------------------------------------------------
--------------------------------------------------------------
--------------------------------------------------------------
Power By O.N.I.O.N-575968661@qq.com
--------------------------------------------------------------
--------------------------------------------------------------
--------------------------------------------------------------
Found a ST compatible (Winbond/NexFlash) serial flash with 256 64KB blocks; total size 16MB
CCA UART Clock Config: Sel=1 Ovr=1 Div=48
CCA UART Clock rate 125000000Hz
bio: create slab <bio-0> at 0
Switching to clocksource mpcore_gtimer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 32
PCI: no core
PCI: no core
PCI: scanning bus 0
pci 0000:00:00.0: reg 10: [mem 0x18000000-0x18000fff]
pci 0000:00:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:01.0: reg 10: [mem 0x18001000-0x18001fff]
pci 0000:00:01.0: reg 14: [mem 0x18002000-0x18002fff]
pci 0000:00:01.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:02.0: reg 10: [mem 0x1802c000-0x1802cfff]
pci 0000:00:02.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:03.0: reg 10: [mem 0x18024000-0x18024fff]
pci 0000:00:03.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:04.0: reg 10: [mem 0x18025000-0x18025fff]
pci 0000:00:04.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:05.0: reg 10: [mem 0x18026000-0x18026fff]
pci 0000:00:05.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:06.0: reg 10: [mem 0x18027000-0x18027fff]
pci 0000:00:06.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:07.0: reg 10: [mem 0x18012000-0x18012fff]
pci 0000:00:07.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:08.0: reg 10: [mem 0x18013000-0x18013fff]
pci 0000:00:08.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:09.0: reg 10: [mem 0x18014000-0x18014fff]
pci 0000:00:09.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:0a.0: reg 10: [mem 0x1800b000-0x1800bfff]
pci 0000:00:0a.0: reg 14: [mem 0x1800c000-0x1800cfff]
pci 0000:00:0a.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:0b.0: reg 10: [mem 0x18022000-0x18022fff]
pci 0000:00:0b.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:0b.1: reg 10: [mem 0x18021000-0x18021fff]
pci 0000:00:0b.1: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:0c.0: reg 10: [mem 0x18023000-0x18023fff]
pci 0000:00:0c.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:0d.0: reg 10: [mem 0x18020000-0x18020fff]
pci 0000:00:0d.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:0e.0: reg 10: [mem 0x1802a000-0x1802afff]
pci 0000:00:0e.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:0f.0: reg 10: [mem 0x18210000-0x1821ffff]
pci 0000:00:0f.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:10.0: reg 10: [mem 0x18010000-0x18010fff]
pci 0000:00:10.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:11.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:12.0: reg 10: [mem 0x18028000-0x18028fff]
pci 0000:00:12.0: reg 30: [mem 0x00000000-0x000007ff pref]
pci 0000:00:13.0: reg 10: [mem 0x18029000-0x18029fff]
pci 0000:00:13.0: reg 30: [mem 0x00000000-0x000007ff pref]
PCI: Fixing up bus 0
PCIE1 link=1
PCIE1 switching to GEN2
PCIE1 link=1
pci 0001:00:00.0: PME# supported from D0 D3hot D3cold
pci 0001:00:00.0: PME# disabled
PCI: Fixing up bus 0
PCI: bus0: Fast back to back transfers disabled
pci 0001:01:00.0: reg 10: [mem 0x08000000-0x08007fff 64bit]
pci 0001:01:00.0: supports D1 D2
PCI: Fixing up bus 1
PCI: bus1: Fast back to back transfers disabled
pci 0001:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff]
pci 0001:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit]
pci 0001:01:00.0: BAR 0: set to [mem 0x08000000-0x08007fff 64bit] (PCI address [0x8000000-0x8007fff]
pci 0001:00:00.0: PCI bridge to [bus 01-01]
pci 0001:00:00.0:   bridge window [io  disabled]
pci 0001:00:00.0:   bridge window [mem 0x08000000-0x080fffff]
pci 0001:00:00.0:   bridge window [mem pref disabled]
PCIE2 link=1
PCIE2 switching to GEN2
PCIE2 link=1
pci 0002:00:00.0: PME# supported from D0 D3hot D3cold
pci 0002:00:00.0: PME# disabled
PCI: Fixing up bus 0
PCI: bus0: Fast back to back transfers disabled
pci 0002:02:00.0: reg 10: [mem 0x00000000-0x00007fff 64bit]
pci 0002:02:00.0: supports D1 D2
PCI: Fixing up bus 2
PCI: bus2: Fast back to back transfers disabled
pci 0002:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff]
pci 0002:02:00.0: BAR 0: assigned [mem 0x40000000-0x40007fff 64bit]
pci 0002:02:00.0: BAR 0: set to [mem 0x40000000-0x40007fff 64bit] (PCI address [0x40000000-0x40007fff]
pci 0002:00:00.0: PCI bridge to [bus 02-02]
pci 0002:00:00.0:   bridge window [io  disabled]
pci 0002:00:00.0:   bridge window [mem 0x40000000-0x400fffff]
pci 0002:00:00.0:   bridge window [mem pref disabled]
PCIE3 link=1
PCIE3 switching to GEN2
PCIE3 link=1
pci 0003:00:00.0: PME# supported from D0 D3hot D3cold
pci 0003:00:00.0: PME# disabled
PCI: Fixing up bus 0
PCI: bus0: Fast back to back transfers disabled
PCI: Fixing up bus 3
PCI: bus3: Fast back to back transfers enabled
pci 0003:00:00.0: PCI bridge to [bus 03-03]
pci 0003:00:00.0:   bridge window [io  disabled]
pci 0003:00:00.0:   bridge window [mem disabled]
pci 0003:00:00.0:   bridge window [mem pref disabled]
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.15)
msgmni has been set to 245
io scheduler noop registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18000300 (irq = 117) is a 16550
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
--------------------------------------------------------------
--------------------------------------------------------------
--------------------------------------------------------------
Power By O.N.I.O.N-575968661@qq.com
--------------------------------------------------------------
--------------------------------------------------------------
--------------------------------------------------------------
bcmsflash: squash filesystem found at block 29
Creating 4 MTD partitions on "bcmsflash":
0x000000000000-0x000000040000 : "boot"
0x000000040000-0x000000ff0000 : "linux"
0x0000001d00fc-0x000000ff0000 : "rootfs"
0x000000ff0000-0x000001000000 : "nvram"
nflash: found no supported devices
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== PPTP init ===
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1965 buckets, 7860 max)
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
brcmnand: found no supported devices
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
devtmpfs: mounted
Freeing init memory: 184K
ctf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x1
et_module_init: et_txq_thresh set to 0x400
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
wl_module_init: passivemode set to 0x0
wl_module_init: txworkq set to 0x1
eth1: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.86 (r456083)
PCI: Enabling device 0002:02:00.0 (0140 -> 0142)
eth2: Broadcom BCMa8db 802.11 Wireless Controller 6.37.14.86 (r456083)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
jnl: Unknown symbol mem_section (err 0)
jnl: disagrees about version of symbol kmalloc_caches
jnl: Unknown symbol kmalloc_caches (err -22)
jnl: Unknown symbol mem_section (err 0)
jnl: disagrees about version of symbol kmalloc_caches
jnl: Unknown symbol kmalloc_caches (err -22)
xhci_hcd 0000:00:0c.0: xHCI Host Controller
xhci_hcd 0000:00:0c.0: new USB bus registered, assigned bus number 1
xhci_hcd 0000:00:0c.0: irq 112, io mem 0x18023000
xhci_hcd 0000:00:0c.0: Failed to enable MSI-X
xhci_hcd 0000:00:0c.0: failed to allocate MSI entry
usb usb1: No SuperSpeed endpoint companion for config 1  interface 0 altsetting 0 ep 129: using minimum values
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
[xhci-hub] usb2mode:[0]
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: irq 111, io mem 0x18021000
ehci_hcd 0000:00:0b.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0b.0: irq 111, io mem 0x18022000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
cdc_ncm: 14-Mar-2012
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver qmi_wwan
cdc_mbim: loaded
usbcore: registered new interface driver cdc_mbim
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
br0: port 1(vlan1) entering forwarding state
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 2-0:1.0: unable to enumerate USB device on port 2
usb 2-2: new high speed USB device using ehci_hcd and address 4
hub 2-0:1.0: unable to enumerate USB device on port 2
usb 2-2: new high speed USB device using ehci_hcd and address 5
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 2-0:1.0: unable to enumerate USB device on port 2
usb 2-2: new high speed USB device using ehci_hcd and address 11
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 2-0:1.0: unable to enumerate USB device on port 2
hub 2-0:1.0: unable to enumerate USB device on port 2
admin@(none):/tmp/home/root# ifconfig
br0        Link encap:Ethernet  HWaddr C8:3A:35:49:BD:90  
           inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:214 errors:0 dropped:0 overruns:0 frame:0
           TX packets:137 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:22882 (22.3 KiB)  TX bytes:49741 (48.5 KiB)

eth0       Link encap:Ethernet  HWaddr C8:3A:35:49:BD:90  
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:219 errors:0 dropped:0 overruns:0 frame:0
           TX packets:150 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:28253 (27.5 KiB)  TX bytes:51927 (50.7 KiB)
           Interrupt:179 Base address:0x4000

eth1       Link encap:Ethernet  HWaddr C8:3A:35:49:BD:90  
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
           TX packets:147 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:0 (0.0 B)  TX bytes:22041 (21.5 KiB)
           Interrupt:163

lo         Link encapocal Loopback  
           inet addr:127.0.0.1  Mask:255.0.0.0
           UP LOOPBACK RUNNING MULTICAST  MTU:16436  Metric:1
           RX packets:1 errors:0 dropped:0 overruns:0 frame:0
           TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:118 (118.0 B)  TX bytes:118 (118.0 B)

vlan1      Link encap:Ethernet  HWaddr C8:3A:35:49:BD:90  
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:219 errors:0 dropped:0 overruns:0 frame:0
           TX packets:147 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:24311 (23.7 KiB)  TX bytes:50901 (49.7 KiB)

admin@(none):/tmp/home/root#

唯美的风景

kesunji 发表于 2015-5-8 17:19
设备应该是认到了但是配上参数后就是没信号出来。对了，之前忘了说，USB也不工作，下面是Log

ASUSWRT  ...

嗯，看来还是nvram没搞定
usb2.0的吗
据网友说ch22刷了usb和无线都正常。
看来小米这玩意还要研究研究啊
哈哈，腾达N60也是好玩的，做工不错

jack3721

请问千兆双频梅林AC68固件什么时候能刷？

doge

支持LZ

wzhy90

华硕这固件那些地方牛逼？我不懂，一直在用openwrt

kesunji

唯美的风景 发表于 2015-5-8 21:07
嗯，看来还是nvram没搞定
usb2.0的吗
据网友说ch22刷了usb和无线都正常。

我也有一台N60，上周折腾了这里的梅林固件 http://www.snbforums.com/threads ... -rt-n-series.18624/

发现要么千兆不工作，要么5G不工作，要是版主有空，帮忙搞搞吧。

jack3721

刷了N18U用了几天，发现手机连WIFI经常连不上，不知是F451硬件问题还是软件问题，WIFI信号明明不错就是连不上，是不是我设置不对？

fazili

我发觉版主就是高富帅，土豪！我们能做朋友么

coffilk

不知道版主什么时候能发布merlin

赵阳光

迅雷屌丝路由不知道怎么样

iSkyun

华硕固件有什么特点？怎么好多人刷啊