找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 4544|回复: 8

N16 变砖,详见贴内描述

[复制链接]
发表于 2015-9-1 13:20 | 显示全部楼层 |阅读模式
本帖最后由 lq2001 于 2015-9-1 13:26 编辑

N16,一直好好,刷TT的固件
今天断电有1小时,
重新上电,出现以下故障;
自检到一半,电源灯就灭了,然后整个路由全灭灯,

感觉应该像是硬件的固件

另附TTL输出,如下: 然后就全黑了

CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: ?  5る 27 16:47:24 CST 2009 (root@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.3
CPU type 0x19740: 480MHz
Tot mem: 131072 KBytes

CFE mem:    0x80700000 - 0x8079B310 (635664)
Data:       0x80731B30 - 0x80734880 (11600)
BSS:        0x80734880 - 0x80735310 (2704)
Heap:       0x80735310 - 0x80799310 (409600)
Stack:      0x80799310 - 0x8079B310 (8192)
Text:       0x80700000 - 0x80731B30 (203568)

Device eth0:  hwaddr BC-AE-C5-E7-89-D3, ipaddr 192.168.2.1, mask 255.255.255.0
        gateway not set, nameserver not set
Null Rescue Flag.
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: TFTP Server.
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: .. 5192 bytes read
Entry at 0x80001000
Starting program at 0x80001000
Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #1 Sat Mar 30 16:20:26 CST 2013
CPU revision is: 00019740
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 32512
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 pkg 10 at 480 MHz
Using 240.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126932k/131068k available (2121k kernel code, 3992k reserved, 460k data, 108k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.5
Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x2000000 at 0x1c000000
Creating 5 MTD partitions on "hysically mapped flash":
0x00000000-0x00040000 : "pmon"
0x00040000-0x01fe0000 : "linux"
0x00120400-0x007a0000 : "rootfs"
0x007a0000-0x01fe0000 : "jffs2"
0x01fe0000-0x02000000 : "nvram"
Found a 0MB  serial flash
sflash: found no supported devices
u32 classifier
    OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
net/ipv4/netfilter/tomato_ct.c [Mar 30 2013 16:20:26]
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 108k freed
Warning: unable to open an initial console.

我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2015-9-1 13:31 | 显示全部楼层
其中

0x00000000-0x00040000 : "pmon"
0x00040000-0x01fe0000 : "linux"
0x00120400-0x007a0000 : "rootfs"
0x007a0000-0x01fe0000 : "jffs2"
0x01fe0000-0x02000000 : "nvram"
Found a 0MB  serial flash

是不是有点不对,flash
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-9-1 14:48 | 显示全部楼层
重新刷下固件试试看...
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2015-9-1 16:05 | 显示全部楼层
本帖最后由 lq2001 于 2015-9-1 17:32 编辑

不行:
用官方的救援模式
提示"连接到无线设备失败!请检查灯亮信号以确认救援操作是否仍在进行"


现在是救援模式不断电,正常启动模式启动到一半就断电;

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2015-9-1 16:05 | 显示全部楼层
更新下用救援模式失败后的TTL输出,和之前的不一样

CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: ?  5る 27 16:47:24 CST 2009 (root@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.3
CPU type 0x19740: 480MHz
Tot mem: 131072 KBytes

CFE mem:    0x80700000 - 0x8079B310 (635664)
Data:       0x80731B30 - 0x80734880 (11600)
BSS:        0x80734880 - 0x80735310 (2704)
Heap:       0x80735310 - 0x80799310 (409600)
Stack:      0x80799310 - 0x8079B310 (8192)
Text:       0x80700000 - 0x80731B30 (203568)

Device eth0:  hwaddr BC-AE-C5-E7-89-D3, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Null Rescue Flag.
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: TFTP Server.
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: .. 3856 bytes read
Entry at 0x80001000
Starting program at 0x80001000
Linux version 2.6.24.111 (root@dd-wrt) (gcc version 4.1.2) #1977 Sat Aug 7 00:53:12 CEST 2010
CPU revision is: 00019740
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Built 1 zonelists in Zone order.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM4716 rev 1 at 480 MHz
Using 240.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 124656k/131068k available (3144k kernel code, 6264k reserved, 1479k data, 144k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
PCI: Using membase 8000000
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
RT-N16 GPIO Init
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
VID 0 is set in nvram, Ignoring
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.27
Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x2000000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x1fb5dc
partition size = 2174976
Creating 5 MTD partitions on "hysically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x01fe0000 : "linux"
0x0018d000-0x003a0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x01fe0000-0x02000000 : "nvram"
0x003a0000-0x01fe0000 : "ddwrt"
Found a 0MB  serial flash
sflash: found no supported devices
Broadcom Watchdog Timer: 0.07 initialized.
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length    128 bytes
PF_RING: ring slots       4096
PF_RING: sample rate      1 [1=no sampling]
PF_RING: capture TX       No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
decode 1f02
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 144k freed
start service
starting Architecture code for broadcom
Booting device: Asus RT-N16
loading bcm57xx
sh: can't create /proc/switch/eth0/reset: nonexistent directory
sh: can't create /proc/switch/eth1/reset: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/0/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/0/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/1/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/1/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/2/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/2/ports: nonexistent directory
/etc/preinit: line 66: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
eth1: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
nbw = 20
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Invalid argument
eth1: Invalid argument
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device br0 entered promiscuous mode
Algorithmics/MIPS FPU Emulator v1.5
br0: Bad file descriptor
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
br0: Bad file descriptor
eth1: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
nbw = 20
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Invalid argument
eth1: Invalid argument

然后就断电了
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2015-9-1 16:44 | 显示全部楼层
我感觉 过段时间N16故障会是论坛经常性热帖

点评

有同感。。。  发表于 2015-9-1 18:29
我的买的是原装港版的..  详情 回复 发表于 2015-9-1 17:37
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2015-9-1 17:37 | 显示全部楼层
xn1126 发表于 2015-9-1 16:44
我感觉 过段时间N16故障会是论坛经常性热帖

我的买的是原装港版的..
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-28 23:31

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表