|
|
附上调试信息
[ 0.000000] Linux version 4.1.13 (tymon@PandoraBox-Server) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r47892) ) #45 Fri Dec 25 10:39:39 CST 2015
[ 0.000000] MyLoader: sysp=a5b6e56f, boardp=a295660c, parts=84c4942d
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803b3de0, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=AP135-020 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfs),1472k(kernel),64k(art)ro,7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125532K/131072K available (2799K kernel code, 140K rwdata, 572K rodata, 256K init, 195K bss, 5540K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5309056796 ns
[ 0.000006] sched_clock: 32 bits at 360MHz, resolution 2ns, wraps every 5965232126ns
[ 0.007847] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048)
[ 0.070538] pid_max: default: 32768 minimum: 301
[ 0.075297] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.081920] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091081] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.101417] NET: Registered protocol family 16
[ 0.106867] MIPS: machine is Atheros AP135-020 reference board
[ 0.332924] ar71xx: using random MAC address for eth1
[ 0.554646] ar724x-pci ar724x-pci.0: PCIe link is down
[ 0.559771] registering PCI controller with io_map_base unset
[ 0.565700] registering PCI controller with io_map_base unset
[ 0.578082] PCI host bridge to bus 0000:00
[ 0.582164] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.589141] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.594742] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.601613] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.609632] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.609745] PCI host bridge to bus 0000:01
[ 0.613829] pci_bus 0000:01: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.620762] pci_bus 0000:01: root bus resource [io 0x0001]
[ 0.626402] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[ 0.633259] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.641307] pci 0000:01:00.0: [168c:003c] type 00 class 0x028000
[ 0.641320] pci 0000:01:00.0: invalid calibration data
[ 0.646482] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.646537] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.646587] pci 0000:01:00.0: supports D1
[ 0.646599] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[ 0.646774] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.646800] pci 0000:01:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.654161] pci 0000:01:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
[ 0.661433] pci 0000:01:00.0: using irq 41 for pin 1
[ 0.667054] Switched to clocksource MIPS
[ 0.671944] NET: Registered protocol family 2
[ 0.677006] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.684017] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.690434] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.696900] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.702767] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.709299] NET: Registered protocol family 1
[ 0.713684] PCI: CLS 0 bytes, default 32
[ 0.714479] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.733596] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.739471] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.751437] io scheduler noop registered
[ 0.755336] io scheduler deadline registered (default)
[ 0.760746] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.767458] console [ttyS0] disabled
[ 0.791051] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.799718] console [ttyS0] enabled
[ 0.806739] bootconsole [early0] disabled
[ 0.816912] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.822610] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.827500] 6 cmdlinepart partitions found on MTD device spi0.0
[ 0.833501] Creating 6 MTD partitions on "spi0.0":
[ 0.838373] 0x000000000000-0x000000040000 : "u-boot"
[ 0.844100] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.850158] 0x000000050000-0x000000680000 : "rootfs"
[ 0.855805] mtd: device 2 (rootfs) set to be root filesystem
[ 0.861625] 1 squashfs-split partitions found on MTD device rootfs
[ 0.867910] 0x000000280000-0x000000680000 : "rootfs_data"
[ 0.874004] 0x000000680000-0x0000007f0000 : "kernel"
[ 0.879696] 0x0000007f0000-0x000000800000 : "art"
[ 0.885099] 0x000000050000-0x0000007e0000 : "firmware"
[ 0.904645] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 0.994521] libphy: ag71xx_mdio: probed
[ 1.588558] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 1.599863] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.188646] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII
[ 2.196738] NET: Registered protocol family 10
[ 2.204236] NET: Registered protocol family 17
[ 2.208852] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.221765] 8021q: 802.1Q VLAN Support v1.8
[ 2.231862] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.239976] Freeing unused kernel memory: 256K (803d0000 - 80410000)
[ 3.049941] init: Console is alive
[ 3.053556] init: - watchdog -
[ 4.031186] usbcore: registered new interface driver usbfs
[ 4.036816] usbcore: registered new interface driver hub
[ 4.042334] usbcore: registered new device driver usb
[ 4.056102] SCSI subsystem initialized
[ 4.064866] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.072619] ehci-platform: EHCI generic platform driver
[ 4.078026] ehci-platform ehci-platform.0: EHCI Host Controller
[ 4.084050] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 4.094322] ehci-platform ehci-platform.0: TX-TX IDP fix enabled
[ 4.100442] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 4.117088] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 4.124286] hub 1-0:1.0: USB hub found
[ 4.128356] hub 1-0:1.0: 1 port detected
[ 4.132629] ehci-platform ehci-platform.1: EHCI Host Controller
[ 4.138692] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 4.148983] ehci-platform ehci-platform.1: TX-TX IDP fix enabled
[ 4.155084] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 4.177076] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 4.184267] hub 2-0:1.0: USB hub found
[ 4.188344] hub 2-0:1.0: 1 port detected
[ 4.195704] usbcore: registered new interface driver usb-storage
[ 5.060399] init: - preinit -
[ 5.647355] eth1: link up (1000Mbps/Full duplex)
[ 5.670437] random: procd urandom read with 8 bits of entropy available
[ 8.857020] jffs2: notice: (390) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 8.874251] mount_root: switching to jffs2 overlay
[ 8.901302] eth1: link down
[ 8.912529] procd: - early -
[ 8.915523] procd: - watchdog -
[ 9.590894] procd: - ubus -
[ 10.655256] procd: - init -
[ 11.175386] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.189246] Loading modules backported from Linux version master-2015-12-03-0-g1677f62
[ 11.197315] Backport generated by backports.git backports-20151120-0-g906a6b3
[ 11.219099] cfg80211: World regulatory domain updated:
[ 11.224322] cfg80211: DFS Master region: unset
[ 11.228775] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.238661] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.246772] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.254894] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.263018] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 11.272637] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 11.282253] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 11.290461] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 11.298586] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 11.387854] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 11.394017] ath10k_pci 0000:01:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0
[ 11.737948] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 11.747336] ath10k_pci 0000:01:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 1 testmode 1
[ 11.760370] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.70.12-2 api 5 features no-p2p,raw-mode crc32 cc3fb466
[ 11.811507] ath10k_pci 0000:01:00.0: found invalid board magic
[ 11.817746] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 12.862123] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 12.970102] ath: EEPROM regdomain: 0x0
[ 12.970116] ath: EEPROM indicates default country code should be used
[ 12.970124] ath: doing EEPROM country->regdmn map search
[ 12.970139] ath: country maps to regdmn code: 0x3a
[ 12.970148] ath: Country alpha2 being used: US
[ 12.970155] ath: Regpair used: 0x3a
[ 12.981643] cfg80211: Regulatory domain changed to country: US
[ 12.987594] cfg80211: DFS Master region: FCC
[ 12.991837] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 13.001725] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 13.009845] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 13.019464] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 13.029080] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
[ 13.037290] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 13.045405] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 13.102231] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.130606] nf_conntrack version 0.5.0 (1965 buckets, 7860 max)
[ 13.187780] xt_time: kernel timezone is -0000
[ 13.204241] PPP generic driver version 2.4.2
[ 13.225631] NET: Registered protocol family 24
[ 13.242904] ath: EEPROM regdomain: 0x0
[ 13.242919] ath: EEPROM indicates default country code should be used
[ 13.242926] ath: doing EEPROM country->regdmn map search
[ 13.242942] ath: country maps to regdmn code: 0x3a
[ 13.242950] ath: Country alpha2 being used: US
[ 13.242957] ath: Regpair used: 0x3a
[ 13.256340] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 13.258800] ieee80211 phy1: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47
[ 19.202308] eth1: link up (1000Mbps/Full duplex)
[ 19.218063] device eth1 entered promiscuous mode
[ 19.225626] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 19.281083] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.197134] br-lan: port 1(eth1) entered forwarding state
[ 20.202651] br-lan: port 1(eth1) entered forwarding state
[ 20.237133] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 20.778532] eth0: link up (1000Mbps/Full duplex)
[ 20.783356] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.197061] br-lan: port 1(eth1) entered forwarding state
[ 22.611837] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 22.642044] ath10k_pci 0000:01:00.0: no channel configured; ignoring frame(s)!
[ 22.652215] device wlan0 entered promiscuous mode
[ 22.980234] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 22.986794] br-lan: port 2(wlan0) entered forwarding state
[ 22.992427] br-lan: port 2(wlan0) entered forwarding state
[ 24.987094] br-lan: port 2(wlan0) entered forwarding state
[ 51.249570] random: nonblocking pool is initialized |
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡