|
|
我有个杂牌的，配置也是你这个机子一样的，我WEB设置的时候没有完成就断电了，现在进不去WEB设置了，但是启动都没有问题，如果有线桥接也可以当交换机用，怎么能刷，我看你这个进U-BOOT，然后按9，我这怎么是F2,F2键按了直接继续跑U-BOOT了。
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE
U-Boot 1.1.4 (Aug 6 2014 - 16:49:28) Marvell version: 3.5.9 - v16288q
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D1340
Soc: 88F6281 A1
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
Module 1 is TDM
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0, egiga1 [PRIME]
Hit "F2" key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x300000
3145728 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-3.3.8
Created: 2014-11-05 9:19:12 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1130456 Bytes = 1.1 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.3.8 (zhangbin@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #3 Wed Nov 5 01:19:07 PST 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Prafly M8621T Router Board
[ 0.000000] Ignoring unrecognised tag 0x41000403
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200 init=/etc/preinit root=/dev/mtdblock2 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 516412k/516412k available, 7876k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc02d5000 (2868 kB)
[ 0.000000] .init : 0xc02d5000 - 0xc02f5000 ( 128 kB)
[ 0.000000] .data : 0xc02f6000 - 0xc0313d40 ( 120 kB)
[ 0.000000] .bss : 0xc0313d64 - 0xc0342a14 ( 188 kB)
[ 0.000000] NR_IRQS:114
[ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: orion_gpio0
[ 0.000000] gpiochip_add: registered GPIOs 32 to 49 on device: orion_gpio1
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 15.125507] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[ 15.215488] pid_max: default: 32768 minimum: 301
[ 15.215629] Mount-cache hash table entries: 512
[ 15.215923] CPU: Testing write buffer coherency: ok
[ 15.216135] Setting up static identity map for 0x275d10 - 0x275d4c
[ 15.217738] NET: Registered protocol family 16
[ 15.219713] Kirkwood: MV88F6281-A1, TCLK=200000000.
[ 15.219728] Feroceon L2: Enabling L2
[ 15.219763] Feroceon L2: Cache support initialised.
[ 15.222079] Kirkwood PCIe port 0:
[ 15.222086] link up
[ 15.222093] PCI: bus0 uses PCIe port 0
[ 15.222248] PCI host bridge to bus 0000:00
[ 15.222261] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
[ 15.222273] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 15.222559] PCI: bus0: Fast back to back transfers disabled
[ 15.222895] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff 64bit]
[ 15.231480] bio: create slab <bio-0> at 0
[ 15.232392] SCSI subsystem initialized
[ 15.233281] usbcore: registered new interface driver usbfs
[ 15.233421] usbcore: registered new interface driver hub
[ 15.233574] usbcore: registered new device driver usb
[ 15.234658] Switching to clocksource orion_clocksource
[ 15.236256] NET: Registered protocol family 2
[ 15.236386] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 15.236618] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 15.236969] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 15.237148] TCP: Hash tables configured (established 16384 bind 16384)
[ 15.237157] TCP reno registered
[ 15.237167] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 15.237189] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 15.237361] NET: Registered protocol family 1
[ 15.238606] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 15.238619] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 15.238926] msgmni has been set to 1008
[ 15.238955] io scheduler noop registered
[ 15.238964] io scheduler deadline registered (default)
[ 15.306007] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 15.326761] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 15.706975] console [ttyS0] enabled
[ 15.711267] SCSI Media Changer driver v0.25
[ 15.716773] NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
[ 15.725452] Scanning device for bad blocks
[ 15.746408] Bad eraseblock 319 at 0x0000027e0000
[ 15.832807] Bad eraseblock 1871 at 0x00000e9e0000
[ 15.841046] Bad eraseblock 1938 at 0x00000f240000
[ 15.871146] Bad eraseblock 2420 at 0x000012e80000
[ 15.878483] Bad eraseblock 2470 at 0x0000134c0000
[ 15.969115] Creating 5 MTD partitions on "orion_nand":
[ 15.974277] 0x000000000000-0x000000100000 : "u-boot"
[ 15.980150] 0x000000100000-0x000000300000 : "kernel"
[ 15.985992] 0x000000300000-0x000002000000 : "rootfs"
[ 15.991822] mtd: partition "rootfs" set to be root filesystem
[ 15.997667] mtd: partition "rootfs_data" created automatically, ofs=680000, len=1980000
[ 16.005809] 0x000000680000-0x000002000000 : "rootfs_data"
[ 16.012016] 0x000000100000-0x000002000000 : "firmware"
[ 16.018008] 0x000002000000-0x000020000000 : "usrdata"
[ 16.024760] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 16.031709] mv643xx_eth smi: probed
[ 16.035930] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 28:51:32:0a:8a:1e
[ 16.045310] mv643xx_eth_port mv643xx_eth_port.1: eth1: port 0 with MAC address 28:51:32:0a:8a:1f
[ 16.054251] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 16.060861] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 16.066182] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 16.094699] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 16.114687] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 16.121175] hub 1-0:1.0: USB hub found
[ 16.124971] hub 1-0:1.0: 1 port detected
[ 16.129296] Initializing USB Mass Storage driver...
[ 16.134360] usbcore: registered new interface driver usb-storage
[ 16.140411] USB Mass Storage support registered.
[ 16.145493] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 16.151530] cpuidle: using governor ladder
[ 16.156993] mmc0: mvsdio driver initialized, using GPIO 43 for card detection
[ 16.164604] TCP cubic registered
[ 16.167867] NET: Registered protocol family 17
[ 16.172344] Zeus Base Module loaded, version: 1.0.00
[ 16.177347] Zeus Sysview Module loaded, version: 1.0.00
[ 16.182603] Zeus Netinet Module loaded, version: 1.0.00
[ 16.187861] Zeus Datrie Module loaded, version: 1.0.00
[ 16.193021] Zeus Strace Module loaded, version: 1.0.00
[ 16.198323] Zeus State Module loaded, version: 1.0.00
[ 16.208759] Zeus Dpi Layer7 Module loaded, version: 1.0.00
[ 16.214387] Zeus Domain Module loaded, version: 1.0.00
[ 16.219595] Zeus Notice Module loaded, version: 1.0.00
[ 16.224876] Zeus Ipv4fw Module loaded, version: 1.0.00
[ 16.230048] Zeus Audit Module loaded, version: 1.0.00
[ 16.244327] rx_desc_queue length: 4096, tx_desc_queue length: 0
[ 16.250316] Zeus Network Core Module loaded, version: 1.0.00
[ 16.256024] Zeus Http Module loaded, version: 1.0.00
[ 16.262706] Zeus Smtp Module loaded, version: 1.0.00
[ 16.267771] Zeus Common QQ Module loaded, version: 1.0.00
[ 16.273221] Zeus Mobile QQ Module loaded, version: 1.0.00
[ 16.278686] Zeus PIN Module loaded, version: 1.0.00
[ 16.283619] Zeus Efence Module loaded, version: 1.0.00
[ 16.288954] Distributed Switch Architecture driver version 0.1
[ 16.295623] eth0[0]: detected a Marvell 88E6171/88E6171R switch
[ 16.408094] dsa slave smi: probed
[ 16.411531] 8021q: 802.1Q VLAN Support v1.8
[ 16.415973] rtc-mv rtc-mv: setting system clock to 2000-01-15 08:52:21 UTC (947926341)
[ 16.427148] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 16.434607] Freeing init memory: 128K
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 20.775682] JFFS2 notice: (1452) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 10 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 21.595045] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 21.603004] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 21.623380] cfg80211: Calling CRDA to update world regulatory domain
[ 21.629828] cfg80211: World regulatory domain updated:
[ 21.635004] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 21.643224] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 21.651015] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 21.658807] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 21.666593] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 21.674372] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 21.775633] NET: Registered protocol family 10
[ 22.234901] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xe0be0000, irq=9
[ 22.252834] usbcore: registered new interface driver rt2800usb
[ 22.316906] PPP generic driver version 2.4.2
[ 22.518727] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 22.688367] NET: Registered protocol family 24
[ 22.704331] nf_conntrack version 0.5.0 (8070 buckets, 32280 max)
[ 23.370278] xt_time: kernel timezone is -0000
[ 24.063034] xt_length2: Unknown symbol ipv6_find_hdr (err 0)
[ 24.138427] nf_conntrack_rtsp v0.6.21 loading
[ 24.151872] nf_nat_rtsp v0.6.21 loading
[ 24.182066] xt_RAWNAT: Unknown symbol ipv6_find_hdr (err 0)
[ 24.204837] xt_SYSRQ: Unknown symbol ipv6_find_hdr (err 0)
[ 24.272784] Netfilter messages via NETLINK v0.30.
[ 24.352230] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 24.483293] ip_set: protocol 6
[ 24.702797] ctnetlink v0.93: registering with nfnetlink.
[ 24.874196] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 24.881218] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 25.024929] usbcore: registered new interface driver ath9k_htc
[ 27.537901] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 27.551810] mv643xx_eth_port mv643xx_eth_port.1: eth1: link up, 1000 Mb/s, full duplex, flow control disabled
BusyBox v1.19.4 (2014-11-04 21:08:12 PST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@pioneer:/# [ 32.438096] cfg80211: Calling CRDA for country: CN
[ 32.442975] cfg80211: Regulatory domain changed to country: CN
[ 32.448867] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 32.457099] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 32.464525] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 33.951483] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 33.996535] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 34.133011] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
root@pioneer:/# REBOOT
/bin/ash: REBOOT: not found
root@pioneer:/# CD TMP
/bin/ash: CD: not found
root@pioneer:/# LS
/bin/ash: LS: not found
root@pioneer:/# HELP
/bin/ash: HELP: not found
root@pioneer:/# HELP
/bin/ash: HELP: not found
root@pioneer:/# reboot
root@pioneer:/# [ 93.420759] Restarting system.
|
|
楼主: 3MD
| 江苏省互联网有害信息举报中心 举报信箱：js12377 | @jischina.com.cn 举报电话：025-88802724
本站不良内容举报信箱：68610888@qq.com
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
显身卡
发表于 2017-3-16 13:39
