求教网件3800TTL刷机

雕刻时光7424

使用TTL链接电脑后信息显示如下：
▒▒
U-Boot 1.1.4 (May 27 2011 - 14:58:01)
DNI HW ID: 29763654 flash 16MB RAM 128MB (ar7100) U-boot dni25 V0.1
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 265k for U-Boot at: 87fbc000
Reserving 192k for malloc() at: 87f8c000
Reserving 44 Bytes for Board Info at: 87f8bfd4
Reserving 36 Bytes for Global Data at: 87f8bfb0
Reserving 128k for boot params() at: 87f6bfb0
Stack Pointer at: 87f6bf98
Now running in RAM - U-Boot at: 87fbc000
id read 0x100000ff
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment
In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
CHH:mac: 0 if: 2
CHH:mac:verify: 0 if: 00000002
: cfg1 0xf cfg2 0x7014
in rtl8366s_phy_setup mac=-1476803788
after rtl8366s_initChip ret=0
eth0: 04:a1:51:ab:7c:e7
eth0 up
CHH:mac: 1 if: 1
CHH:mac:verify: 1 if: 00000001
: cfg1 0xf cfg2 0x7014
in rtl8366s_phy_setup mac=-1476803308
eth1: 04:a1:51:ab:7c:e8
eth1 up
eth0, eth1
Trying eth0
: unit 0 phy is up...RGMii 1000Mbps full duplex
#259:ag7100_set_mac_from_link
: pll reg 0x18050010: 0x11110000
: cfg_1: 0x1ff0000
: cfg_2: 0x3ff
: cfg_3: 0x8001ff
: cfg_4: 0xffff
: cfg_5: 0xfffef
: done cfg2 0x7215 ifctl 0x40605060 miictrl 0x22
Client starts...[Listening] for ADVERTISE...TTT
Retry count exceeded; boot the image as usual
nmrp server is stopped or failed !
Hit any key to stop autoboot:  0
   Verifying Checksum ... OK
### SQUASHFS loading 'image/uImage' to 0x80800000
### SQUASHFS load complete: 1179648 bytes loaded to 0x80800000
## Booting image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.17
   Created:      2015-07-13  16:28:22 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1146097 Bytes =  1.1 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[    0.000000] Linux version 3.18.17 (avril@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46293) ) #8 Tue Jul 14 00:27:55 CST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7161 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=WNDR3700 mtdparts=spi0.0:320k(u-boot),128k(u-boot-env)ro,15872k(firmware),64k(art) console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 125920K/131072K available (2488K kernel code, 122K rwdata, 528K rodata, 244K init, 188K bss, 5152K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[    0.000000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070000] NET: Registered protocol family 16
[    0.080000] MIPS: machine is NETGEAR WNDR3700/WNDR3800/WNDRMAC
[    2.710000] registering PCI controller with io_map_base unset
[    2.720000] PCI host bridge to bus 0000:00
[    2.720000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[    2.730000] pci_bus 0000:00: root bus resource [io  0x0000]
[    2.730000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.740000] pci 0000:00:11.0: fixup device configuration
[    2.740000] pci 0000:00:12.0: fixup device configuration
[    2.750000] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    2.750000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
[    2.760000] pci 0000:00:11.0: using irq 40 for pin 1
[    2.760000] pci 0000:00:12.0: using irq 41 for pin 1
[    2.770000] Switched to clocksource MIPS
[    2.770000] NET: Registered protocol family 2
[    2.780000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.780000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    2.790000] TCP: Hash tables configured (established 1024 bind 1024)
[    2.790000] TCP: reno registered
[    2.800000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    2.800000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    2.810000] NET: Registered protocol family 1
[    2.820000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    2.830000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.830000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.840000] msgmni has been set to 245
[    2.860000] io scheduler noop registered
[    2.860000] io scheduler deadline registered (default)
[    2.870000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
▒[    2.900000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 10625000) is a 16550A
[    2.910000] console [ttyS0] enabled
[    2.910000] console [ttyS0] enabled
[    2.910000] bootconsole [early0] disabled
[    2.910000] bootconsole [early0] disabled
[    2.920000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[    2.930000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    2.940000] 4 cmdlinepart partitions found on MTD device spi0.0
[    2.940000] Creating 4 MTD partitions on "spi0.0":
[    2.950000] 0x000000000000-0x000000050000 : "u-boot"
[    2.950000] 0x000000050000-0x000000070000 : "u-boot-env"
[    2.960000] 0x000000070000-0x000000ff0000 : "firmware"
[    2.980000] 2 netgear-fw partitions found on MTD device firmware
[    2.990000] 0x000000070000-0x000000189440 : "kernel"
[    2.990000] 0x000000189440-0x000000ff0000 : "rootfs"
[    3.000000] mtd: device 4 (rootfs) set to be root filesystem
[    3.000000] 1 squashfs-split partitions found on MTD device rootfs
[    3.010000] 0x000000c60000-0x000000ff0000 : "rootfs_data"
[    3.020000] 0x000000ff0000-0x000001000000 : "art"
[    3.020000] Realtek RTL8366S ethernet switch driver version 0.2.2
[    3.030000] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[    3.030000] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[    3.070000] libphy: rtl8366s: probed
[    3.390000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    3.710000] ag71xx ag71xx.1: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[    3.720000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII
[    3.720000] TCP: cubic registered
[    3.730000] NET: Registered protocol family 17
[    3.730000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    3.740000] 8021q: 802.1Q VLAN Support v1.8
[    3.760000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    3.760000] Freeing unused kernel memory: 244K (80373000 - 803b0000)
[    4.930000] init: Console is alive
[    4.930000] init: - watchdog -
[    7.010000] usbcore: registered new interface driver usbfs
[    7.020000] usbcore: registered new interface driver hub
[    7.020000] usbcore: registered new device driver usb
[    7.030000] exFAT: Version 1.2.9
[    7.040000] SCSI subsystem initialized
[    7.050000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.060000] ehci-platform: EHCI generic platform driver
[    7.060000] ehci-platform ehci-platform: EHCI Host Controller
[    7.070000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    7.080000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    7.100000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    7.100000] hub 1-0:1.0: USB hub found
[    7.110000] hub 1-0:1.0: 2 ports detected
[    7.110000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.120000] ohci-platform: OHCI generic platform driver
[    7.120000] ohci-platform ohci-platform: Generic Platform OHCI controller
[    7.130000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    7.140000] ohci-platform ohci-platform: irq 14, io mem 0x1c000000
[    7.210000] hub 2-0:1.0: USB hub found
[    7.210000] hub 2-0:1.0: 2 ports detected
[    7.220000] usbcore: registered new interface driver usb-storage
[    7.940000] init: - preinit -
[    8.540000] eth0: link up (1000Mbps/Full duplex)
[    8.560000] random: procd urandom read with 13 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   11.830000] jffs2: notice: (365) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   11.840000] mount_root: switching to jffs2 overlay
[   11.880000] eth0: link down
[   11.890000] procd: - early -
[   11.890000] procd: - watchdog -
[   12.610000] procd: - ubus -
[   13.630000] procd: - init -
Please press Enter to activate this console.
[   15.970000] NET: Registered protocol family 10
[   15.980000] ntfs: driver 2.1.31 [Flags: R/O MODULE].
[   16.020000] tun: Universal TUN/TAP device driver, 1.6
[   16.020000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   16.030000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   16.060000] Netfilter messages via NETLINK v0.30.
[   16.060000] ip_set: protocol 6
[   16.130000] u32 classifier
[   16.130000]     input device check on
[   16.140000]     Actions configured
[   16.140000] Mirror/redirect action on
[   16.150000] nf_conntrack version 0.5.0 (1971 buckets, 7884 max)
[   16.220000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   16.230000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   16.240000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.480000] usbcore: registered new interface driver ums-alauda
[   16.490000] usbcore: registered new interface driver ums-cypress
[   16.500000] usbcore: registered new interface driver ums-datafab
[   16.500000] usbcore: registered new interface driver ums-freecom
[   16.510000] usbcore: registered new interface driver ums-isd200
[   16.520000] usbcore: registered new interface driver ums-jumpshot
[   16.540000] usbcore: registered new interface driver ums-karma
[   16.550000] usbcore: registered new interface driver ums-sddr09
[   16.550000] usbcore: registered new interface driver ums-sddr55
[   16.560000] usbcore: registered new interface driver ums-usbat
[   16.650000] xt_time: kernel timezone is -0000
[   16.690000] cfg80211: Calling CRDA to update world regulatory domain
[   16.750000] cfg80211: World regulatory domain updated:
[   16.750000] cfg80211:  DFS Master region: unset
[   16.750000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   16.760000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   16.770000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   16.780000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   16.790000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   16.800000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   16.810000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   16.810000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   16.820000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   16.850000] PPP generic driver version 2.4.2
[   16.860000] NET: Registered protocol family 24
[   16.880000] usbcore: registered new interface driver rt73usb
[   16.890000] usbcore: registered new interface driver rtl8187
[   16.950000] usbcore: registered new interface driver rt2500usb
[   16.980000] usbcore: registered new interface driver rt2800usb
[   17.010000] usbcore: registered new interface driver rtl8192cu
[   17.040000] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[   17.060000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[   17.070000] cfg80211: Calling CRDA for country: US
[   17.090000] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
[   17.120000] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0010000, irq=41
[   17.150000] cfg80211: Regulatory domain changed to country: US
[   17.150000] cfg80211:  DFS Master region: FCC
[   17.160000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   17.170000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   17.170000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[   17.180000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[   17.190000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   17.200000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   22.880000] eth0: link up (1000Mbps/Full duplex)
[   22.880000] device eth0.1 entered promiscuous mode
[   22.890000] device eth0 entered promiscuous mode
[   22.900000] br-lan: port 1(eth0.1) entered forwarding state
[   22.900000] br-lan: port 1(eth0.1) entered forwarding state
[   22.940000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   24.900000] br-lan: port 1(eth0.1) entered forwarding state
[   38.470000] warning: process `cjdroute' used the deprecated sysctl system call with 1.40.6.
[   38.740000] capability: warning: `cjdroute' uses 32-bit capabilities (legacy support in use)
[   78.730000] random: nonblocking pool is initialized
这个路由器是由一个第三方公司自己搞过的，刷入了他们的广告固件。路由IP为：10.1.1.1.但是由于使用中出现问题他们公司又已经没有人负责这一块了。我想把路由重新刷一个固件来使用，有广告固件当然最好了。小白一个，还望大家多多赐教。TTL我已经连接好的了。

雕刻时光7424

请问高手，这种还有得刷吗？

chanwah2009

先中断，然后找个  网件的固件刷上试试

雕刻时光7424

chanwah2009 发表于 2016-1-22 10:38
先中断，然后找个  网件的固件刷上试试

目前已经刷好一个固件了，原来被我刷了之后IP由10.1.1.1换为192.168.8.1了。但是我不知道要如何加入微信认证

xiahui

对了，楼上的，能备份一下的3800的固件 uboot 和ART么，我的原唱的对了

xiahui

我原厂的flash挂了，换了新的，网上找的一些编程器固件都有问题

caidi1224

不懂帮顶！

xiahui

我用网上找的不死uboot 固件 还有ART做的编程器固件不行，很是郁闷

雕刻时光7424

xiahui 发表于 2016-1-22 13:35
对了，楼上的，能备份一下的3800的固件 uboot 和ART么，我的原唱的对了

我不懂怎么备份啊，你的意思是我备份一个传给你使用吗？

xiahui

雕刻时光7424 发表于 2016-1-22 15:49
我不懂怎么备份啊，你的意思是我备份一个传给你使用吗？

会TTL就行，备份一个我试下，我合成编程器固件用的，我这要弄好了的挂也发给你刷机

雕刻时光7424

xiahui 发表于 2016-1-22 16:01
会TTL就行，备份一个我试下，我合成编程器固件用的，我这要弄好了的挂也发给你刷机

你要教我才行哦，说实话我真小白一个，不然也不会来这问了。你加我QQ51312419

xiahui

secureCRT登陆路由（用户名root，密码为你刚才修改的密码），putty应该也是可以的，运行cd /tmp，
再运行dd if=/dev/mtd0 of=/tmp/uboot.bin(备份原始uboot)，以及dd if=/dev/mtd4 of=/tmp/art.bin(备份原始art)

winscp登陆路由进入/tmp将备份的原厂uboot及art拷贝到电脑进行备份。

雕刻时光7424

xiahui 发表于 2016-1-22 16:04
secureCRT登陆路由（用户名root，密码为你刚才修改的密码），putty应该也是可以的，运行cd /tmp，
再运行d ...

我使用TTL之后输入这些命令都不管用，所以才要你QQ远程呢