求助华硕路由器RT-N53刷成TT固件！

netantsboy

本人刚思考怎么刷机，还是小白，请求大神帮忙。昨晚在一个网友的帮忙下用USBTTL工具读出路由信息如下：
Decompressing...done


CFE version 5.70.55.33 @VERSION_TYPE@ based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 三  1月  2 13:05:22 CST 2013 (root@raymonddev-vm)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found a 8MB ST compatible serial flash
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.70.55.33 @VERSION_TYPE@
CPU type 0x19749: 500MHz
Tot mem: 32768 KBytes

CFE mem:    0x80700000 - 0x8079FDE0 (654816)
Data:       0x80735C30 - 0x80738E60 (12848)
BSS:        0x80738E60 - 0x80739DE0 (3968)
Heap:       0x80739DE0 - 0x8079DDE0 (409600)
Stack:      0x8079DDE0 - 0x8079FDE0 (8192)
Text:       0x80700000 - 0x80735C2C (220204)

Device eth0:  hwaddr BC-EE-7B-54-EC-CB, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: CFE works as TFTP Server.
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: .. 5100 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
start_kernel
Linux version 2.6.22.19 (root@asus) (gcc version 4.2.4) #1 Sat Jan 10 20:46:31 CST 2015
CPU revision is: 00019749
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
wombo_reset set to gpio 22
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
CPU: BCM5357 rev 2 pkg 8 at 500 MHz
Using 250.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28924k/32768k available (2455k kernel code, 3844k reserved, 492k data, 160k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: no core
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
pflash: found no supported devices
Creating 5 MTD partitions on "sflash":
0x00000000-0x00020000 : "pmon"
0x00020000-0x007f0000 : "linux"
0x001499ec-0x00730000 : "rootfs"
0x007f0000-0x00800000 : "nvram"
0x00770000-0x007f0000 : "jffs2"
dev_nvram_init: _nvram_init
_nvram_init: allocat header: 2151612416, size= 32768
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
u32 classifier
    OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
ipt_time loading
ip_tables: (C) 2000-2006 Netfilter Core Team
net/ipv4/netfilter/tomato_ct.c [Jan 10 2015 20:45:53]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 160k freed
Warning: unable to open an initial console.
set_action 0
firmware version: 3.0.0.4.376_3754-g5ef7c1f
clean_mode(1) clean_time(2) threshold(0)
free_caches: Start syncing...
free_caches: Start cleaning...
free_caches: waiting 2 second...
free_caches: Finish.
[1 init:init_nvram +6] init_nvram for 26
num_of_mssid_support(0x0092): [mssid] support [3] mssid
ctf: module license 'Proprietary' taints kernel.
et_module_init: passivemode set to 0x1
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.110.27.20012
hotplug net INTERFACE=eth0 ACTION=add
wl_module_init: passivemode set to 0x1
eth1: Broadcom BCM4329 802.11 Wireless Controller 5.110.27.20012
hotplug net INTERFACE=eth1 ACTION=add
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.1: EHCI Fastpath: New EHCI driver starting
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
Symbol usb_deregister is being used by a non-GPL module, which will not be allowed in the future
Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.
bcm_rpc_up: waiting to be connected
bcm_rpc_buf_recv_mgn_high: Reason: 0 Dongle Version: 0x5648a89
bcm_rpc_buf_recv_mgn_high: Connected!
eth2: Broadcom BCMa8e4 802.11 Wireless Controller 5.110.27.20012
usbcore: registered new interface driver dbus_usbdev
hotplug net INTERFACE=eth2 ACTION=add
wl1 is up in 0 sec
[1 init:init_main +12] main loop signal/state=17
start_logger:
Algorithmics/MIPS FPU Emulator v1.5
/ # start_usb
_ifconfig: name=eth0 flags=1043 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=vlan0 ACTION=add
hotplug net INTERFACE=vlan1 ACTION=add
update_lan_state(lan_, 0, 0)
start_lan: setting up the bridge br0
hotplug net INTERFACE=br0 ACTION=add
vlan0: cmd=14: Operation not supported
_ifconfig: name=vlan0 flags=1043 IFUP addr=(null) netmask=(null)
start_lan: setting MAC of br0 bridge to BC:EE:7B:54:EC:CB
_ifconfig: name=eth1 flags=1043 IFUP addr=(null) netmask=(null)
generate_wl_para(0x0e73): unit 0 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
generate_wl_para(0x1133): bw: 1
generate_wl_para(0x1138): channel: 0
generate_wl_para(0x1139): nbw_cap: 1
generate_wl_para(0x113a): nctrlsb: lower
generate_wl_para(0x113c): obss_coex: 1
generate_wl_para(0x0e73): unit 0 subunit 1
generate_wl_para(0x0e73): unit 0 subunit 2
generate_wl_para(0x0e73): unit 0 subunit 3

_ifconfig: name=eth2 flags=1043 IFUP addr=(null) netmask=(null)
generate_wl_para(0x0e73): unit 1 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
generate_wl_para(0x1133): bw: 1
generate_wl_para(0x1138): channel: 0
generate_wl_para(0x1139): nbw_cap: 1
generate_wl_para(0x113a): nctrlsb: lower
generate_wl_para(0x113c): obss_coex: 1
generate_wl_para(0x0e73): unit 1 subunit 1
generate_wl_para(0x0e73): unit 1 subunit 2
generate_wl_para(0x0e73): unit 1 subunit 3

_ifconfig: name=br0 flags=1043 IFUP addr=192.168.1.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
update_lan_state(lan_, 2, 0)
stop_nat_rules: apply the redirect_rules!
# wanduck: Got LAN(-1) information:
start_lan 1773
start_services 3251

# Enable direct rule
[1 init:start_dnsmasq +17] begin
[1 init:stop_dnsmasq +17] begin
[1 init:stop_dnsmasq +17] end
[1 init:start_dnsmasq +18] end
start_lan_port(0) 1
decomp: fname=/var/lib/misc/rstats-speed.gz
TZ watchdog
decomp: gzip -dc /var/lib/misc/rstats-speed.gz > /var/tmp/rstats-uncomp != 0
load: speed_count = 0
load: read source= save_path=
load_history: fname=/var/lib/misc/rstats-history.gz
decomp: fname=/var/lib/misc/rstats-history.gz
start_pptpd: getpid= 1
vlan0: cmd=14: Operation not supported
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
decomp: fname=/var/lib/misc/rstats-history.gz
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
load_history: load failed
start_wan: start_wan_if(0)!
[1 init:start_wan_if +18] unit=0.
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
update_wan_state(wan0_, 1, 0)
_ifconfig: name=eth0 flags=1043 IFUP addr=(null) netmask=(null)
start_auth:: done
udhcpc_wan:: deconfig
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=(null)
start_wan_if(): End.
wan_down(eth0)
wan_down(eth0): .
stop_auth:: done
route_manip: cmd=DEL name=eth0 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
update_wan_state(wan0_, 3, 0)
update_wan_state(wan0_, 4, 3)
udhcpc:: deconfig done
clean_mode(1) clean_time(2) threshold(0)
free_caches: Start syncing...
free_caches: Start cleaning...
free_caches: waiting 2 second...
free_caches: Finish.
[1 init:init_main +21] main loop signal/state=14
NET CMD GETINFO
NET CMD GETINFO
NET CMD GETINFO

今天这位朋友就不在线了，请问我接下来要该怎么做呢？可否一步一步教我？

mal032349

http://news.softpedia.com/news/H ... Router-457324.shtml


简单来说，就是下载工具，进入恢复模式，然后用工具刷入TT

固件地址

https://advancedtomato.com/downloads/router/rt-n53

如果是墙外上不了的话那就等别人吧

好像NAP6上也有教程

netantsboy

谢谢楼上的解说呀，不过那个教程都是英文的看不懂，翻译也不完整。

durendal

netantsboy 发表于 2016-9-11 22:39
谢谢楼上的解说呀，不过那个教程都是英文的看不懂，翻译也不完整。

目前还在更新的Tomato固件都是英文的，楼主英文水平不过关的话，就算刷好了固件也不会用啊。

如果你还是坚持要刷的话，建议搜一下其他华硕路由器刷Tomato的教程吧，应该能找到中文教程的。华硕路由器刷Tomato的过程大同小异，区别基本就只有刷进去的固件不同而已，操作方法是基本一致的 。固件的话就刷2楼那个专版固件就行。

其实主要是写一个完整的教程太麻烦了，要花不少时间的。估计很少有人愿意为你一个人特意写一个完整教程。