rg100e-ca bcm5357刷华硕n14uhp cfe怎么修改vlan

csm***

rg100e-ca  bcm5357刷华硕n14uhp重启后，无线连接正常能进路由界面.但是用电脑浏览器输入路由ip无法进入路由界面.所有端口都试过不行，听说把cfe文件的vlan端口修改一下就好了。请大神们帮忙改一下，谢谢
下面是cfe请大神们帮忙改一下vlan
boardtype=0x0550
boardnum=0629
boardrev=0x1102
clkfreq=500,200,100
xtalfreq=20000
sdram_config=0x104
sdram_refresh=0x2060
sdram_ncdl=0x58000020
boardpwrctl=0x00000c00
et_swtype=1
et0macaddr=18:80:F5:11:10:EE
et0phyaddr=30
et0mdcport=0
vlan1hwname=et0
vlan1ports=1 2 3 4 5*
vlan2hwname=et0
vlan2ports=0 5
landevs=vlan1 wl0 wl1
wandevs=vlan2
lan_ipaddr=192.168.1.1
lan_netmask=255.255.255.0
boot_wait=on
boot_part=0
wait_time=3
reset_gpio=21
watchdog=0
boardflags=0x710
boardflags2=0x1000
sromrev=8
devid=0x4347
macaddr=18:80:F5:11:20:EE
ccode=0
regrev=0
ledbh0=0xff
ledbh1=0xff
ledbh2=0xff
ledbh3=0xff
ledbh5=7
leddc=0xffff
opo=0x0
aa2g=0x3
ag0=0x2
ag1=0x2
ag2=0xff
ag3=0xff
bxa2g=0x3
rssisav2g=0x7
rssismc2g=0xf
rssismf2g=0xf
tri2g=0xff
rxpo2g=0xff
txchain=0x3
rxchain=0x3
antswitch=0x0
tssipos2g=0x1
extpagain2g=0x2
pdetrange2g=0x2
triso2g=0x3
triso5g=0x3
antswctl2g=0x1
cck2gpo=0x1111
ofdm2gpo=0x44222222
mcs2gpo0=0x2222
mcs2gpo1=0x4442
mcs2gpo2=0x2222
mcs2gpo3=0x4442
mcs2gpo4=0x6666
mcs2gpo5=0x9666
mcs2gpo6=0x6666
mcs2gpo7=0xa666
cddpo=0x0
stbcpo=0x0
bw40po=0x0
bwduppo=0x0
maxp2ga0=0x4e
itt2ga0=0x20
pa2gw1a0=0x1560
pa2gw2a0=0xfb03
pa2gw0a0=0xff0c
maxp2ga1=0x4e
itt2ga1=0x20
pa2gw1a1=0x1597
pa2gw2a1=0xfaf9
pa2gw0a1=0xff03
gpio6=wps
gpio9=usb
gpio28=aoss
gpio29=wps
gpio21=reset
wl_msglevel=0x1
product_class=v1.0
wl_ssid=SSID-1234
wl_wpapsk=12345678
user_pass=1234
device_id=0123456789
start_flag=0
factoryData=1
qtdc_vid=2652
qtdc_pid=48407
qtdc1_sz=10
qtdc0_sz=5
qtdc1_ep=18
qtdc0_ep=4

wr***

找下别人发的cfe，看看就知道了