赚钱宝pro ttl中断不了 谁有方法吗 这个是前半部分的信息

long1983

QA5:A;SVN:B72;   POC:1FF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;   PASS:0;
no sdio debug board detectedj
                             BT : 14:51:46 Jun 12 2016
PMU:NONE
##### VDDEE voltage = 0x044c1100

CPU clock is 792MHz

DDR mode: 16 bit mode lane0+1
DDR size: 512MB (auto)
DDR check: Pass!
DDR clock: 636MHz with 2T mode
DDR pll bypass: Disabled
DDR init use : 17492 us

HHH
Boot From SDIO C
SD_boot_type: 00000002
card_type: 00000003
0x0000009f
ucl decompress...pass
0x12345678
Boot from internal device 1st eMMC on SDIO C

TE : 398039

System Started


U-boot-00000-g6d8fe6f-dirty(m8b_m201_v1@) (Jun 12 2016 - 14:51:24)

clr h-ram
DRAM:  512 MiB
relocation Offset is: 0feb8000
show partition table:
part: 0, name :      uboot, size : 2000000
part: 1, name :     kernel, size : 2000000
part: 2, name :       misc, size : 2000000
part: 3, name :       boot, size : 2000000
part: 4, name :     system, size : 10000000
part: 5, name :     backup, size : 10000000
part: 6, name :       data, size : end
aml_card_type=0x200
MMC:   [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
power init
out reg=c110804c,value=dfffffff
IR init done!
register usb cfg[0][1] = 1ff68178
register usb cfg[2][0] = 1ff6b2ec
init 32k clock
enter emmc boot
Emmckey: Access range is illegal!
[mmc_init] SDIO Port C:1, if_type=6, initialized OK!
Partition table get from SPL is :
        name                        offset              size              flag
===================================================================================
   0: bootloader                         0            400000                  0
   1: reserved                     2400000           4000000                  0
   2: cache                        6c00000                 0                  0
   3: env                          7400000            800000                  0
   4: uboot                        8400000           2000000                  1
   5: kernel                       ac00000           2000000                  1
   6: misc                         d400000           2000000                  1
   7: boot                         fc00000           2000000                  1
   8: system                      12400000          10000000                  1
   9: backup                      22c00000          10000000                  1
  10: data                        33400000          b5c00000                  4
mmc read lba=0x12000, blocks=0x1
mmc read lba=0x12001, blocks=0x1
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
i=0,register --- emmc_key
device_boot_flag=2
EMMC BOOT: not init nand
do not init nand : cause boot_device_flag without nand
MMC BOOT, emmc_env_relocate_spec : env_relocate_spec 74
set_storage_device_flag: store 2
vpu clk_level in dts: 3
set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
Net:   Meson_Ethernet
init suspend firmware done. (ret:0)
cvbs trimming.1.v5: 0xa0, 0x0
reboot_mode=charging
hdmi tx power init
TV mode 1080p selected.
mode = 8  vic = 16
set HDMI vic: 16
mode is: 8
viu chan = 1
config HPLL
config HPLL done
reconfig packet setting done
Can not find partition name "logo"
Cannot find dev.
mmc cmd read failed

nand cmd store failed
Err imgread(L519):Fail to read 0x2000B from part[logo] at offset 0
There is no valid bmp file at the given address
bmp scale:  mode=1080p , x=0, y=0, w=1920, h=1080
info data len is 1
efuse version has been written [20]
out reg=c8100024,value=bffb3fff
out reg=c8100024,value=bff33ffb
out reg=c8100024,value=bfe33ff3
out reg=c8100024,value=bfeb3fe3
Hit Enter key to stop autoboot -- :  0
exit abortboot: 0
Enter USB burn
Try connect time out 701, 700, 1263
Booting...
Saving Environment to eMMC...
MMC BOOT,emmc_saveenv : saveenv 131
mmc save env ok
pos 509 value is 20pos 509 value is 20aml_keys: version 0 can not be init 1ff6b4e8
current storer:emmc_key
ERR(v2_common/optimus_download_key.c)L473:failed to query key state, rc 0, keyIsBurned=0
## ANDROID Format IMAGE
## Booting kernel from Legacy Image at 12000000 ...
   Image Name:   Linux-3.10.33
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    4497607 Bytes = 4.3 MiB
   Load Address: 00208000
   Entry Point:  00208000
   Verifying Checksum ... OK
    Ramdisk start addr = 0x1244b000, len = 0x25a8ec
    Flat device tree start addr = 0x126a6000, len = 0x3cb2 magic=0xedfe0dd0
   Uncompressing Kernel Image ... OK
uboot time: 2859730 us.
EFUSE machid is not set.
Using machid 0xf81 from environment
From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x5262001
   Loading Ramdisk to 05007000, end 052618ec ... OK
   Loading Device Tree to 05000000, end 05006cb1 ... OK

Starting kernel ...

wangyuddd000

就是中断不了，直接就输root密码了

long1983

wangyuddd000 发表于 2020-11-21 19:18
就是中断不了，直接就输root密码了

密码是多少中断不了没法设置启动效应，

wangyuddd000

long1983 发表于 2020-11-22 11:59
密码是多少中断不了没法设置启动效应，

输入密码说明中断不成功，已进入openwrt系统了

csu05michael

wangyuddd000 发表于 2020-11-24 06:05
输入密码说明中断不成功，已进入openwrt系统了

先线刷S805通用固件试试呢？

xupx

看log中断时间设置为0了

long1983

xupx 发表于 2021-2-20 20:27
看log中断时间设置为0了

已经放弃，