求助： N1 开机卡logo，卡了2年了

liu*** · 发表于 2020-12-17 15:57

求助：N1 卡logo18年弄双系统之后就挂了，这两天尝试了下面两种刷机（
1. T1 v3_20180419_2 卡21% 之后再刷 N1 6.2.3
2. TTL - USB
usb_update  bootloader bootloader.img
usb_update  recovery recovery.img
usb_update  boot  boot.img

update
刷N1_mod_by_webpad_v2.2_20180920 ）

两种刷机，最后usb burn工具都能到100%，然后提示成功，可是依然卡开机画面。下面是TLL - PUTTY的console output。

GXL:BL1:9ac50e:bb16dc;FEAT:BDFC31BC:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 257051
BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 4
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 [url=home.php?mod=space&uid=162986]@[/url] 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
aml log : R2048 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
aml log : R2048 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
aml log : R2048 check pass!
Load bl33 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00053400
aml log : R2048 check pass!
NOTICE: BL3-1: v1.0(release):a625749
NOTICE: BL3-1: Built : 11:25:15, Aug 25 2017
[BL31]: GXL CPU setup!
NOTICE: BL31: BL33 decompress pass
mpu_config_enable:ok
[Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
OPS=0x04
8d 85 8 c5 d3 cb 99 9e 8c aa b0 61 [0.845055 Inits done]
secure task start!
high task start!
low task start!
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01-00010-gfe36fb9 (Mar 02 2018 - 19:00:28)
DRAM: 2 GiB
Relocation Offset is: 76ed9000
register usb cfg[0][1] = 0000000077f5d330
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
MMC: aml_priv->desc_buf = 0x0000000073ed9640
aml_priv->desc_buf = 0x0000000073edb960
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
dtb magic 71b104da
aml log : R2048 check pass!
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxl platform: p230 variant: 2g
dtb 0 soc: gxl plat: p230 vari: 1g
dtb 1 soc: gxl plat: p230 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073ede1b0,dt_addr=0000000073ee91b0
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxl platform: p230 variant: 2g
dtb 0 soc: gxl plat: p230 vari: 1g
dtb 1 soc: gxl plat: p230 vari: 2g
Find match dtb: 1
parts: 10
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: boot 0000000002000000 1
07: system 0000000050000000 1
08: cache 0000000020000000 2
09: data ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970000
HPLL: 0xc000027b
config HPLL done
j = 4 vid_clk_div = 1
hdmitx: set enc for VIC: 16
HDMITX-DWC addr=0x10004006 rd_data=0x40
Error: HDMITX-DWC exp_data=0xff mask=0x9f
rx version is 2.0 div=10
hdmtix: set audio
hdmitx phy setting done
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-917: calc 96094b61, store 96094b61
_verify_dtb_checksum()-917: calc 96094b61, store 96094b61
dtb_read()-1039: total valid 2
dtb_read()-1106: do nothing
aml log : R2048 check pass!
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 2 dtbs.
aml_dt soc: gxl platform: p230 variant: 2g
dtb 0 soc: gxl plat: p230 vari: 1g
dtb 1 soc: gxl plat: p230 vari: 2g
Find match dtb: 1
vpp: vpp_pq_load pq val error !!!
Net: Phy 0 not found
dwmac.c9410000amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
Start read misc partition datas!
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[CANVAS]addr=0x7f851000 width=3840, height=2160
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
InUsbBurn
noSof
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
[imgread]szTimeStamp[2018030720035817]
[imgread]secureKernelImgSz=0xd88800
aml log : R-2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
ee_gate_off ...
mmc env offset: 0x27400000
Writing to MMC(1)... done
## Booting Android Image at 0x01080000 ...
reloc_addr =73f5e400
copy done
Kernel command line: buildvariant=user
load dtb from 0x1000000 ......
Amlogic multi-dtb tool
Single dtb detected
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x021d4598
Loading Ramdisk to 73894000, end 73ec7000 ... OK
Loading Device Tree to 000000001fff2000, end 000000001ffff6b8 ... OK
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 3883528 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-00007-gff93835 (jenkins@slave2) (gcc version 4.9.3 (Ubuntu/Linaro 4.9.3-13ubuntu2) ) #1 SMP PREEMPT Wed Mar 7 19:32:34 CST 2018
[ 0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
[ 0.000000@0] Reserved memory: incorrect alignment of CMA region
[ 0.000000@0] [amvecm] pq string error !!!
[ 0.187655@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.190157@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[ 0.198344@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[ 0.206249@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
[ 0.228385@0] tv_vout: chrdev devno 266338304 for disp
[ 0.242559@0] 1507 node need 400ms
[ 0.927350@0] Initramfs unpacking failed: junk in compressed archive
[ 1.020166@1] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.150815@1] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[ 1.157031@1] ATVR driver - init called!
[ 1.166026@0] get_storage_dev return 1
[ 1.305368@1] DI-di_probe: get flag_cma error.
[ 1.307366@1] PPMGRDRV: err: ppmgr_driver_probe called
efuse_pw_en: 0x7
WARNING! efuse bits is disabled
Enable A53 JTAG to AO
[ 1.338469@1] cectx aocec: no hdmirx reg resource
[ 1.338498@1] cectx aocec: no hhi reg resource
[ 1.557834@1] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTL
[ 1.559838@1] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[ 1.568717@1] aml_snd_m8_card aml_m8_snd.47: ASoC: no source widget found for LOUTR
[ 1.576247@1] aml_snd_m8_card aml_m8_snd.47: ASoC: Failed to add route LOUTR -> direct -> Ext Spk

复制代码

实在没辙了，不知道是哪里的问题
如果是硬件故障，有什么办法可以确定是哪里的问题么？emmc，cpu还是内存？谢谢 🙏

马上2021了，能让用外置u盘做个openwrt就知足，不妄放了这么多年。。。

恩山*** · 发表于 2020-12-17 16:01

50包邮解君愁

liu*** · 发表于 2020-12-17 16:05

时子航发表于 2020-12-17 16:01
50包邮解君愁

别，我那个时候是80块钱买的。。。理论折价40可以卖。
可是有了遥控器，电源，TTL，电烙铁，焊锡这一堆，就不舍得了。😄

ko*** · 发表于 2020-12-17 16:07

liutim 发表于 2020-12-17 16:05
别，我那个时候是80块钱买的。。。理论折价40可以卖。
可是有了遥控器，电源，TTL，电烙铁，焊锡这一堆 ...

那就连工具一起打包60包邮

liu*** · 发表于 2020-12-17 16:09

kover 发表于 2020-12-17 16:07
那就连工具一起打包60包邮

哈哈，再给些时间，我想折腾

cyn*** · 发表于 2020-12-17 16:10

换emmc就好了，不会换的话出给我吧

2441*** · 发表于 2020-12-17 16:11

刷机能到100%也有启动行，可以试试cpu加焊或者重新焊接

liu*** · 发表于 2020-12-17 16:13

cynizy 发表于 2020-12-17 16:10
换emmc就好了，不会换的话出给我吧

uboot 命令行那个地方mmcinfo可以看到有3个blk的，如果emmc坏了，外部u盘系统可以启动么？

liu*** · 发表于 2020-12-17 16:16

244135002 发表于 2020-12-17 16:11
刷机能到100%也有启动行，可以试试cpu加焊或者重新焊接

对，搜到的各种刷机最后都可以成功。
通过TTL outpu 确实有的时候启动可以看到顺序从CPU3, CPU2, CPU1, CPU1 fatal的dump。是怀疑cpu掉了么？

2441*** · 发表于 2020-12-17 16:31

liutim 发表于 2020-12-17 16:16
对，搜到的各种刷机最后都可以成功。
通过TTL outpu 确实有的时候启动可以看到顺序从CPU3, CPU2, CPU1, ...

我这边维修也遇到很多这样的，加焊或者重新焊接cpu就可以了

zr*** · 发表于 2020-12-17 16:33

有ttl应该可以连上的，是不是ttl电压没设置好。

cyn*** · 发表于 2020-12-17 16:34

244135002 发表于 2020-12-17 16:11
刷机能到100%也有启动行，可以试试cpu加焊或者重新焊接

这种情况我确实遇到过一台，换emmc好了

poy*** · 发表于 2020-12-17 17:45

要焊emmc，出掉吧，我的也卖了，emmc损坏

liu*** · 发表于 2020-12-20 15:12

😒，RX,TX的焊点被我不小心弄掉了。。。封贴。

cyn*** · 发表于 2020-12-21 07:44

liutim 发表于 2020-12-20 15:12
😒，RX,TX的焊点被我不小心弄掉了。。。封贴。

老铁出给我研究研究吧

账号		自动登录	找回密码
密码			立即注册

[N1盒子] 求助： N1 开机卡logo，卡了2年了

相关帖子

点评

点评

点评

点评

点评