求助7620a 不能刷老毛子 刷op正常

§~stil***

7620a 不能刷老毛子 刷op正常 以下是启动ttl 输出第一个是老毛子卡死  刷了各种老毛子都一样
第二是op正常启动 已经是Breed刷的了u-boot也试了 一样的
4M-16M的都刷过了都不能启动卡死到
No filesystem could mount root, tried:  squashfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,4)
op刷的是4m-16M的都正常
板子就是单7620asoc
求大神能教刷老毛子



U-Boot firmware image header detected.
    Image Name:         RT-N14U-GPIO-2-FIR300M-
    Data Size:    3500942 Bytes
    Load Address: 80000000
    Entry Point:  80239c00
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x80239c00...


LINUX started...
Linux version 3.4.113 (padavan@hms) (gcc version 4.4.7 (GCC) ) #1 Sat Apr 17 15:22:48 CST 2021

MediaTek SoC: MT7620A, RevID: 0206, RAM: DDR2, XTAL: 20MHz
CPU/OCP/SYS frequency: 580/193/193 MHz
CONFIG_RALINK_RAM_SIZE:32MB
prom get memory:128MB
CPU revision is: 00019650 (MIPS 24KEc)
Determined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
Early memory PFN ranges
    0: 0x00000000 -> 0x00008000
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 32512
Kernel command line: console=ttyS0,57600n8 root=/dev/mtdblock4 rootfstype=squashfs
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Writing ErrCtl register=0001befa
Readback ErrCtl register=0001befa
Memory: 127016k/131072k available (2298k kernel code, 4056k reserved, 338k data, 176k init, 0k highmem)
NR_IRQS:40
console [ttyS0] enabled
Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 248
io scheduler noop registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
Ralink GPIO driver initialized. Number of GPIO: 73, GPIO mode: 005A171D
loop: module loaded
Ralink SPI flash driver, SPI clock: 48MHz
unrecognized SPI chip ID: ff (e01b0000), please update the SPI driver!
SPI flash chip: Unknown (00 ffffffff) (4096 Kbytes)
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x00000014fd40 : "Kernel"
0x00000014fd40-0x0000003c0000 : "RootFS"
0x0000003c0000-0x000000400000 : "Storage"
0x000000050000-0x000000400000 : "Firmware_Stub"
Ralink APSoC Ethernet Driver v3.2.4 (raeth)
raeth: PDMA RX ring 256, PDMA TX ring 512. Max packet size 1536
raeth: NAPI support, weight 32
raeth: Byte Queue Limits (BQL) support
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
p p t p driver version 0.8.5
nf_conntrack version 0.5.0 (8192 buckets, 16384 max)
xt_time: kernel timezone is -0000
Bridge firewalling registered
gre: GRE over IPv4 demultiplexor driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
ASUS NVRAM, v0.08. Available space: 61440. Integrity: Signature FAILED!
List of all partitions:
1f00             192 mtdblock0  (driver?)
1f01              64 mtdblock1  (driver?)
1f02              64 mtdblock2  (driver?)
1f03            1023 mtdblock3  (driver?)
1f04            2496 mtdblock4  (driver?)
1f05             256 mtdblock5  (driver?)
1f06            3776 mtdblock6  (driver?)
No filesystem could mount root, tried:  squashfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,4)



分割线——————————————————————————————————————


U-Boot firmware image header detected.
    Image Name:   MIPS OpenWrt Linux-3.14.18
    Data Size:    1052439 Bytes
    Load Address: 80000000
    Entry Point:  80000000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.

Starting kernel at 0x80000000...

[    0.000000] Linux version 3.14.18 (latyas@keeg) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42620) ) #16 Sun Sep 21 16:17:00 CST 2014
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: Ralink MT7620A ver:2 eco:6
[    0.000000] MIPS: machine is FIR300M
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00019ef0
[    0.000000] Readback ErrCtl register=00019ef0
[    0.000000] Memory: 126684K/131072K available (2290K kernel code, 123K rwdata, 456K rodata, 128K init, 180K bss, 4388K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 580MHz
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] genirq: Flags mismatch irq 7. 00014600 (timer) vs. 00014600 (systick)
[    0.010000] Calibrating delay loop... 766.77 BogoMIPS (lpj=3833856)
[    0.050000] pid_max: default: 32768 minimum: 301
[    0.050000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060000] pinctrl core: initialized pinctrl subsystem
[    0.070000] NET: Registered protocol family 16
[    0.080000] bio: create slab <bio-0> at 0
[    0.080000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.090000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.090000] Switched to clocksource systick
[    0.100000] NET: Registered protocol family 2
[    0.100000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.120000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.130000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.150000] TCP: reno registered
[    0.150000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.150000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.180000] NET: Registered protocol family 1
[    0.180000] rt-timer 10000100.timer: maximum frequency is 2441Hz
[    0.200000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.220000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.240000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.260000] msgmni has been set to 247
[    0.260000] io scheduler noop registered
[    0.280000] io scheduler deadline registered (default)
[    0.280000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.300000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
[    0.320000] console [ttyS0] enabled
[    0.320000] console [ttyS0] enabled
[    0.340000] bootconsole [early0] disabled
[    0.340000] bootconsole [early0] disabled
[    0.360000] m25p80 spi32766.0: found w25q32, expected mx25l3205d
[    0.360000] m25p80 spi32766.0: w25q32 (4096 Kbytes)
[    0.380000] 4 ofpart partitions found on MTD device spi32766.0
[    0.380000] Creating 4 MTD partitions on "spi32766.0":
[    0.400000] 0x000000000000-0x000000030000 : "u-boot"
[    0.410000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.420000] 0x000000040000-0x000000050000 : "factory"
[    0.430000] 0x000000050000-0x000000400000 : "firmware"
[    0.450000] 0x000000150f57-0x000000400000 : "rootfs"
[    0.450000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.480000] mtd: device 4 (rootfs) set to be root filesystem
[    0.500000] mtd: partition "rootfs_data" created automatically, ofs=0x380000, len=0x80000
[    0.500000] 0x000000380000-0x000000400000 : "rootfs_data"
[    0.520000] ralink_soc_eth 10100000.ethernet: Enabling TSO
[    0.540000] (unregistered net_device): port 2 link up (100Mbps/Full duplex)
[    0.540000] ralink_soc_eth 10100000.ethernet: loaded mt7530 driver
[    0.570000] eth0: done loading
[    0.570000] rt3xxx-usbphy usbphy.3: loaded
[    0.570000] rt2880_wdt 10000120.watchdog: Initialized
[    0.590000] TCP: cubic registered
[    0.600000] NET: Registered protocol family 17
[    0.600000] 8021q: 802.1Q VLAN Support v1.8
[    0.620000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.650000] Freeing unused kernel memory: 128K (802d0000 - 802f0000)
procd: Console is alive
procd: - watchdog -
[    5.470000] usbcore: registered new interface driver usbfs
[    5.480000] usbcore: registered new interface driver hub
[    5.490000] usbcore: registered new device driver usb
[    5.510000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.510000] ehci-platform: EHCI generic platform driver
[    5.920000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[    5.940000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[    5.950000] ehci-platform 101c0000.ehci: EHCI Host Controller
[    5.960000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    5.980000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    6.010000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    6.030000] hub 1-0:1.0: USB hub found
[    6.030000] hub 1-0:1.0: 1 port detected
[    6.040000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.060000] ohci-platform: OHCI generic platform driver
[    6.060000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    6.080000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    6.100000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    6.430000] hub 2-0:1.0: USB hub found
[    6.430000] hub 2-0:1.0: 1 port detected
procd: - preinit -
[    6.770000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.860000] random: mktemp urandom read with 61 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.930000] hub 1-1:1.0: USB hub found
[    6.940000] hub 1-1:1.0: 4 ports detected
jffs2 is not ready - marker found
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[   12.330000] NET: Registered protocol family 10
[   12.350000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.370000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   12.390000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   12.410000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.430000] nf_conntrack version 0.5.0 (1981 buckets, 7924 max)
[   12.470000] xt_time: kernel timezone is -0000
[   12.510000] cfg80211: Calling CRDA to update world regulatory domain
[   12.540000] cfg80211: World regulatory domain updated:
[   12.550000] cfg80211:  DFS Master region: unset
[   12.560000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   12.580000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.600000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.610000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   12.630000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   12.650000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   12.650000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   12.680000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   12.680000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   13.010000] PPP generic driver version 2.4.2
[   13.020000] NET: Registered protocol family 24
[   13.050000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
[   13.070000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[   21.230000] random: nonblocking pool is initialized
[   21.340000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   21.370000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   21.390000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   22.380000] device eth0.1 entered promiscuous mode
[   22.380000] device eth0 entered promiscuous mode
[   22.440000] br-lan: port 1(eth0.1) entered forwarding state
[   22.450000] br-lan: port 1(eth0.1) entered forwarding state
[   24.450000] br-lan: port 1(eth0.1) entered forwarding state
[   26.980000] done.
[   26.990000] jffs2: notice: (856) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   28.010000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   28.040000] device wlan0 entered promiscuous mode
[   28.150000] br-lan: port 2(wlan0) entered forwarding state
[   28.160000] br-lan: port 2(wlan0) entered forwarding state
[   28.170000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
procd: - init complete -
[   30.160000] br-lan: port 2(wlan0) entered forwarding state

邪恶***

先刷个BREED再说

cix***

你单单刷入个breed，在breed下刷入老毛子固件试试
第一个你刷入的是斐讯fir300M的固件，3500942 Bytes的固件，即4M闪存
第二个你刷入的op才1052439Bytes的固件的固件，即1M闪存，不知道我的理解对不对，我也是小白
所以核对下路由器实际的闪存和内存，再找合适的老毛子固件吧

§~stil***

邪恶海盗 发表于 2021-6-11 13:15
先刷个BREED再说

就是通过breed 刷的

§~stil***

cixiclq 发表于 2021-6-11 13:16
你单单刷入个breed，在breed下刷入老毛子固件试试
第一个你刷入的是斐讯fir300M的固件，3500942 Bytes的固 ...

4M-16M的都刷过了都不能启动卡死到
No filesystem could mount root, tried:  squashfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,4)
op刷的是4m-16M的都正常

cix***

红米AC2100如果有坏块会刷不了华硕，刷op就没事，是否和你这个情况一样？

§~stil***

cixiclq 发表于 2021-6-11 14:42
红米AC2100如果有坏块会刷不了华硕，刷op就没事，是否和你这个情况一样？

我换过flash了 还是一样 估计情况不一样

§~stil***

求！ 来个大佬解答下

§~stil***

买的这个路由器 https://www.right.com.cn/forum/thread-1608861-1-1.html