关于Openwrt使用IPv6···我刚把日立AH4021刷成openwrt了·

zxy***

我已经装了一些IPv6的组件···现在使用ping6命令和start radvd都显示“Address family not supported by protocol”
什么原因呢？

tns***

opkg list|grep ipv6看下是否安装了kmod-ipv6内核模块

zxy***

root@OpenWrt:/# opkg list|grep ipv6
6scripts - 0.1-6 - IPv6 scripts to setup ipv6 connectivy using 6to4 tunnels
or bridged ipv6 connectivity.
fake_mipv6 - 0.7-1 - Spoof MIPv6 updates to redirect packets directed at the home-address
fping - 2.4b2_to-ipv6-1 - fping is a ping(1) like program which uses the Internet Control Message Protocol
ipv6calc - 0.73.0-1 - ipv6calc is a small utility written in programming languate C to manipulate
kmod-ebtables-ipv6 - 2.6.35.8-1 - This option adds the IPv6 support to ebtables, which allows basic
kmod-ipv6 - 2.6.35.8-1 - Kernel modules for IPv6 support


显示这个···然后呢

tns***

root@OpenWrt:/# opkg list|grep ipv6
6scripts - 0.1-6 - IPv6 scripts to setup ipv6 connectivy using 6to4 tunnels
or bridged ipv6 connectivity.
fake_mipv6 - 0.7-1 - Spoof MIPv6 updates to redirect p ...
zxy041 发表于 2011-3-17 12:28

那你模块是装了的，那你去看看这个吧：http://wiki.openwrt.org/oldwiki/ipv6_howto

zxy***

好的··我看看·

zxy***

还是没有显示
：：1的地址啊··

root@OpenWrt:/# ifconfig lo
lo        Link encapocal Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:131 errors:0 dropped:0 overruns:0 frame:0
          TX packets:131 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:9912 (9.6 KiB)  TX bytes:9912 (9.6 KiB)

zxy***

root@OpenWrt:/#  ip6tables -L
ip6tables: can't load library 'libxtables.so.5'

tns***

root@OpenWrt:/#  ip6tables -L
ip6tables: can't load library 'libxtables.so.5'
zxy041 发表于 2011-3-17 13:30

ip6tables         1.4.10-1         40255         IPv6 firewall administration tool
libxtables         1.4.10-1         10847         IPv4/IPv6 firewall - shared xtables library
libiptc         1.4.10-1         15689         IPv4/IPv6 firewall - shared libiptc library
kmod-ip6tables         2.6.32.27-1         34789         Netfilter IPv6 firewalling support
kmod-ipv6         2.6.32.27-1         156851         Kernel modules for IPv6 support

可能这些都要装哦

zxy***

装了两个之前没装的···
libxtables         1.4.10-1         10847         IPv4/IPv6 firewall - shared xtables library
libiptc         1.4.10-1         15689         IPv4/IPv6 firewall - shared libiptc library
现在这样子··

root@OpenWrt:/# ip6tables -L
ip6tables v1.4.9.1: can't initialize ip6tables table `filter': Address family not supported by protocol
Perhaps ip6tables or your kernel needs to be upgraded.

zxy***

最终还是指向了这个错误
Address family not supported by protocol

zxy***

我现在lsmod看不到ipv6模块
不知道是不是没有载入

yunhai2***

我也是这个问题

yunhai2***

我也是这个问题，哎，已经弄了好几天了

wang***

我已经装了一些IPv6的组件···现在使用ping6命令和start radvd都显示“Address family not supported by protocol”
什么原因呢？
http://www.anywlan.com/bbs/attac ... DAyYmI3NDljfDEzMDAz ...
zxy041 发表于 2011-3-17 10:55

楼主固件是自己编译的吗？

sunj***

我的也不行啊