求助！openwrt在routerstation pro上的问题

anh***

大家好：
小弟最近在鼓捣着往routerstation pro里导入openwrt，用的是自己编译的内核，刷机的过程没什么问题，但是问题是我通过usb-ttl线连到板子上，然后通过xp自带的超级终端想要通过控制台来安装一些软件时，出现了一些怪异的状况，启动信息卡在一个地方再也下不去了，无论回车怎么样都没反应了，但是通过x-wrt界面登陆没问题，鼓捣了好久都没弄明白为什么，下面是启动信息，每次启动都卡在那个fuse init (API version 7.15）这里，请问各位大虾，这是哪里出问题了吗？还有就是这块板子的flash是16M的，怎么编译版上说的16M内核呀，编译时要选择什么选项？

AR8316 PHY found on MAC0
AR8316 PHY found on MAC1
Ethernet eth0: MAC address 00:15:6d:c7:0b:cb
IP: 192.168.1.20/255.255.255.0, Gateway: 0.0.0.0
Default server: 0.0.0.0
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Ubiquiti Networks certified release, version 0.9.00318M.0905121200 - built 12:01
:38, May 12 2009
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
Board: Ubiquiti RouterStation PRO
Arch: ar7100pro
RAM: 0x80000000-0x88000000, [0x8003bf00-0x87fe1000] available
Flash: 0xbf000000-0xc0000000, in 256 blocks of 0x00010000 bytes each
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> fis load -d -e kernel
Trying LZMA decompression...
Image loaded from 0x80060000-0x802d1ecc
Image is not ELF, skipping ELF parsing...
RedBoot> exec
Now booting linux kernel:
Base address 0x80050000 Entry 0x80060000
memsize=0x08000000
modetty0=0,n,8,1,hw
board=RouterStation PRO
ethaddr=00.15.6d.c7.0b.cb
Linux version 2.6.37.6 (anhome@anhome) (gcc version 4.5.2 (Linaro GCC 4
2-0) ) #2 Thu May 5 17:03:14 CST 2011
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR7161 rev 2
Clocks: CPU:720.000MHz, DDR:360.000MHz, AHB:180.000MHz, Ref:40.000MHz
Determined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility groupi
Kernel command line: board=UBNT-RSPRO console=ttyS0,115200 ethaddr=00.15.6d.c7.
0b.cb rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00018002
Readback ErrCtl register=00018002
Memory: 126912k/131072k available (1959k kernel code, 4160k reserved, 374k data,
168k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:80
Calibrating delay loop... 478.41 BogoMIPS (lpj=2392064)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is Ubiquiti RouterStation Pro
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:11.0: BAR 0: assigned [mem 0x10
pci 0000:00:11.0: BAR 0: set to [mem 0x10000000-0x1000ffff] (PCI address [0x1000for connection...
TFTPD: waiting for connection.
0000-0x1000ffff])
pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
TFTPD: waiting for connection...
pci 0000:00:12.0: BAR 0: set to [mem 0x10010000-0x1001ffff] (PCI address [0x1001iting for connection...
TFTPD: waiting for conne
0000-0x1001ffff])
pci 0000:00:13.0: BAR 0: assigned [mem 0x10020000-0x1002ffff]
TFTPD: waiting for connection...
pci 0000:00:13.0: BAR 0: set to [mem 0x10020000-0x1002ffff] (PCI address [0x1002PD: waiting for connection...
TFTPD: waiting for
0000-0x1002ffff])
PCI: mapping irq 72 to pin1@0000:00:11.0...
TFTP
PCI: mapping irq 73 to pin1@0000:00:12.0
TFTPD: waiting for c
TCP established hash table entries: 4096 (order: 3, 32768 bytes) waiting for connection...
TFTPD
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TFTPD: waiting for connection...
TCP: Hash tables configured (established 4096 bind 4096)
TFTPD: waiting for connection...
TCP reno registered
TFTPD: waiti
UDP hash table entries: 256 (order: 0, 4096 bytes)
TFTPD: waiting for connection...
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
TFTPD: waiting for connection
NET: Registered protocol family 1
TFTPD: waiting for connec
m25p80 spi0.0: found mx25l12805d, expected m25p80
TFTPD: waiting for connection...
m25p80 spi0.0: mx25l12805d (16384 Kbytes)ting for connection...
Searching for RedBoot partition table in spi0.0 at offset 0xfe0000
TFTPD: waiting for connection...
Searching for RedBoot partition table in spi0.0 at offset 0xff0000
TFTPD: waiting for connection...
5 RedBoot partitions found on MTD device spi0.0
TFTPD: waiting for con
Creating 5 MTD partitions on "spi0.0":
TFTPD: waiting for connection...
0x000000000000-0x000000030000 : "RedBoot"ing for connection...
0x000000030000-0x000000100000 : "kernel"n...
TFT
0x000000100000-0x000000ff0000 : "rootfs"
TFTPD: waiting for
mtd: partition "rootfs" set to be root filesystemD: waiting for connection...
ag71xx_mdio: probedg default partition
eth0: Atheros AG71xx at 0xb9000000, irq 4
Created 'k
eth1: Atheros AG71xx at 0xba000000, irq 560000, entry: 0x80060000, si
eth1: AR8316 switch driver attached.
ze: 0
ar8316: Using port 4 as PHYted 'rootfs' - base: 0xBF10
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registerede: 0x00A30000
NET: Registered protocol family 17
... Erase from 0
input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0 'rootfs' (size: 0x00A30000, actual data: 0x004A0000)
Button Hotplug driver version 0.4.1
... Erase from 0xbf1
- preinit -0000: .....
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -...................
JFFS2 notice: (367) jffs2_build_xattr_subsystem: complete building xattr subsyst
.................................

复制代码

字数限制，下半部分的启动信息我在2楼贴出。

anh***

AR8316 PHY found o
usbcore: registered new interface driver hubnd on MAC1
Ethernet
usbcore: registered new device driver usb
IP:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Default server: 0.0.0.0
ar71xx-ehci ar71xx-ehci: Atheros AR71xx built-in EHCI controllerent [ROMRAM]
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1uilt 12:01
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
Copyright (C) 2000, 2001, 2002, 2003, 2004 R
ar71xx-ehci ar71xx-ehci: USB
Re
ar71xx-ohci ar71xx-ohci: irq 14, io mem 0x1c000000
Trying LZMA decompression...
hub 2-0:1.0: USB hub found from 0x80060000-0x802d1ec
hub 2-0:1.0: 2 ports detected
Image is not ELF,
uhci_hcd: USB Universal Host Controller Interface driver
RedBoot> exec
Now booting linux ker
Initializing USB Mass Storage driver...ess 0x80050000 Entry 0x80060000
usbcore: registered new interface driver usb-storage
modetty0=0,n,8,1,hw
Clocks: CPU:720
sd 0:0:0:0: [sda] Attached SCSI removable disk.000MHz
switching to jffs2
Determ
- init -ical RAM
Please press Enter to activate this console. device eth1 entered promiscuous mod
Initrd not found or empty - disabling initrd
e
lib80211: common routines for IEEE802.11 drivers
Normal 0x00000000 -> 0x0000
Compat-wireless backport release: compaMovable zone start P
br-lan: port 1(eth1) entering forwarding state
0b.cb rootfstype=squashfs,jffs2 noinitrd
cfg80211: World regulatory domain updated:D hash table entries: 512 (order: -1, 2048
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)le entries: 16384 (order: 4, 65536 bytes)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)768 bytes)
Pri
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm
168k init,
PCI: Enabling device 0000:00:11.0 (0000 -> 0002)=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
ath5k 0000:00:11.0: registered as 'phy0'
NR
ath5k phy0: Atheros AR5414 chip found (MAC: 0xa5, PHY: 0x61)(lpj=2392064)
PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
Mount-cache has
ath5k 0000:00:12.0: registered as 'phy1'
NET: Registered protocol
ath5k phy1: Atheros AR5414 chip found (MAC: 0xa5, achine is Ubiquiti Rou
cfg80211: Regulatory domain changed to country: AM
0000-0x1000ffff])
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
pci 0000:00:12.0: BAR 0: set to [me
cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
0000-0x1001ffff
cfg80211: (5170000 KHz - 5250000 KHz @ 20000 KHz), (N/A, 1800 mBm)x1002ffff]
cfg80211: (5250000 KHz - 5330000 KHz @ 20000 KHz)0
NET: Registered protocol family 2
RPC: Registered udp transport module.sh table entries: 1024 (order: 0, 409
RPC: Registered tcp transport module.
TCP
RPC: Registered tcp NFSv4.1 backchannel transport module.s)
NTFS driver 2.1.29 [Flags: R/O MODULE].096 (order: 2, 16384 bytes)
PPP generic driver version 2.4.2
TCP: Hash tables co
IPv4 over IPv4 tunneling driver4096)
ip_tables: (C) 2000-2006 Netfilter Core Teamtered
UDP hash table entr
NET: Registered protocol family 24
acx: please read the README file and/or go to http://acx100.sourceforge.net/wiki
io scheduler noop registered
for further informationistered (default)
acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as nong disabled
serial8250.0
n-working firmware upload. Report thems a 16550A
acx: running on a BIG-ENDIAN CPU
console [ttyS0] enabled, bootco
PCI/VLYNQ module initialized, waiting for car
ath_pci: trunk
wlan: trunk
wlan: mac acl policy registered
ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (trunk)
ath_rate_minstrel: look around rate set to 10%
ath_rate_minstrel: EWMA rolloff level set to 75%
ath_rate_minstrel: max segment size in the mrr set to 6000 us
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
fuse init (API version 7.15)

复制代码

anh***

有没有哪位高手能够帮小弟分析下问题所在呢？

wangy***

这个是我的板子信息，这份是原装串口打印的：
fuse init (API version 7.10)
can't load conntrack support for proto=24
can't load conntrack support for proto=24
scsi 0:0:0:0: Direct-Access    Generic  STORAGE DEVICE 9451 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] Attached SCSI removable disk

BusyBox v1.11.3 (2009-05-08 03:07:05 PDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                   ________       __
|    |.-----.-----.-----.|  |  |  |.----.|  |_
| - ||  _  |  -__|    ||  |  |  || _|| _|
|_______|| __|_____|__|__||________||__|  |____|
      |__| W I R E L E S S F R E E D O M
KAMIKAZE (bleeding edge, r15349) -------------------
  * 10 oz Vodka    Shake well with ice and strain
  * 10 oz Triple sec  mixture into 10 shot glasses.
  * 10 oz lime juice  Salute!
---------------------------------------------------
root@RouterStationPro:/#

wangy***

我新编的没有fuse
eth0: link up (100Mbps/Full duplex)
device eth1 entered promiscuous mode
lib80211: common routines for IEEE802.11 drivers
Compat-wireless backport release: compat-wireless-2011-05-11-1-g501c91f
Backport based on wireless-testing.git master-2011-05-13
cfg80211: Calling CRDA to update world regulatory domain
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
eth1: link up (1000Mbps/Full duplex)
br-lan: port 1(eth1) entering forwarding state
br-lan: port 1(eth1) entering forwarding state
cfg80211: World regulatory domain updated:
cfg80211:    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
ieee80211 phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81 mem=0xb0000000, irq=73
cfg80211: Calling CRDA for country: US
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
cfg80211: Regulatory domain changed to country: US
cfg80211:    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211:    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211:    (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR71xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
nf_conntrack version 0.5.0 (1986 buckets, 7944 max)
usb 1-2: new high speed USB device using ar71xx-ehci and address 2
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ar71xx-ohci ar71xx-ohci: Atheros AR71xx built-in OHCI controller
ar71xx-ohci ar71xx-ohci: new USB bus registered, assigned bus number 2
ar71xx-ohci ar71xx-ohci: irq 14, io mem 0x1c000000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected

BusyBox v1.18.4 (2011-07-26 15:09:12 HKT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                   ________       __
|    |.-----.-----.-----.|  |  |  |.----.|  |_
| - ||  _  |  -__|    ||  |  |  || _|| _|
|_______|| __|_____|__|__||________||__|  |____|
      |__| W I R E L E S S F R E E D O M
ATTITUDE ADJUSTMENT (bleeding edge, r27026) ----------
  * 1/4 oz Vodka    Pour all ingredients into mixing
  * 1/4 oz Gin       tin with ice, strain into glass.
  * 1/4 oz Amaretto
  * 1/4 oz Triple sec
  * 1/4 oz Peach schnapps
  * 1/4 oz Sour mix
  * 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/#

lindi***

我也有 rspro

我装的是ar9160网卡

我的从电脑ping 路由的时候，每隔一端时间就出现 100ms的，一般都 1ms 左右。

谁知道为什么呢。

wangy***

启动的时候是不是插了SD卡？

wangy***

https://forum.openwrt.org/viewtopic.php?id=29949
这个bitch也遇到这个问题，最后发现是usb串口的问题

wangy***

6楼的，想问下用其他协议是否就正常呢？比如通过rspro下载东西是否也有延时100ms的情况呢？可能要用chariot打下才知道。
顺便请问下有没有rspro的资料，苦闷中

账号		自动登录	找回密码
密码			立即注册

求助！openwrt在routerstation pro上的问题

相关帖子