FW300R 到底能不能TTL刷机？？？

xll · 发表于 2011-6-22 16:31

进入TTL界面，貌似并没有能刷Uboot，kernel等的命令啊。
cp命令貌似对SPI Flash不支持啊。

729650915 · 发表于 2011-6-22 18:23

cp.b

hiro917 · 发表于 2011-6-22 22:47

UBOOT是相对现版OPENWRT来说的，我试过不能刷(刚入门)
DD的是REDBOOT，REDBOOT似乎能刷

bobo7950 · 发表于 2011-6-23 10:05

绝对可以的，我是买的改好的8m/64已经ttl刷过了

xll · 发表于 2011-6-24 11:02

有时间测试一下

xiangjunfei · 发表于 2011-6-26 15:48

1# xll

搭建好超级终端设置固定IP（192.168.1.169），上电按P……把固件改名（3420.bin）,打开tftp32

setenv serverip 192.168.1.169; setenv ipaddr 192.168.1.1
tftpboot 0x80000000 3420.bin
erase 0x9f020000 +0x3c0000
cp.b 0x80000000 0x9f020000 0x3c0000
bootm 0x9f020000

搞定

tzwlwm · 发表于 2011-6-26 16:12

能的
我今天TTL就修复成功了

tzwlwm · 发表于 2011-6-26 16:13

能的
我今天TTL就修复成功了

live-18 · 发表于 2011-6-26 19:53

问题是楼主不会用TTL搞

jameslord · 发表于 2011-6-27 10:52

能的
我今天TTL就修复成功了
tzwlwm 发表于 2011-6-26 16:12

fw300自带ttl插座的吗？

xll · 发表于 2011-6-30 11:06

恩山终于恢复鸟

xll · 发表于 2011-6-30 11:12

问题是楼主不会用TTL搞
live-18 发表于 2011-6-26 19:53

不是不会搞，而是还没敢搞，正在熟悉中。

已改8M的Flash，正打算换64M内存，大家说有必要吗？？

======================TTL输出=========================

U-Boot 1.1.4 (Dec 24 2010 - 01:07:29)

AP99 (ar7241 - Virian) U-boot mod by AVBIOS
DRAM:
sri
ar7240_ddr_initial_config(133): virian ddr1 init
#### TAP VALUE 1 = 0xf, 2 = 0x10 [0x0: 0x1f]
32 MB
id read 0x100000ff
sector count = 128
Flash:  8 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Autobooting in 1 seconds, press 'p' to stop
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.37.6 (xbmc@XBMCLive) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #12 Tue May 24 21:31:30 CST 2011
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
SoC: Atheros AR7241 rev 1
Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line:  board=TL-MR3420 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29432k/32768k available (1971k kernel code, 3336k reserved, 378k data, 168k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:80
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is TP-LINK TL-MR3420
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:00.0: fixup device configuration
pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1000ffff 64bit] (PCI address [0x10000000-0x1000ffff])
PCI: mapping irq 72 to pin1@0000:00:00.0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: found s25fl064k, expected m25p80
m25p80 spi0.0: s25fl064k (8192 Kbytes)
Searching for RedBoot partition table in spi0.0 at offset 0x7fe000
Searching for RedBoot partition table in spi0.0 at offset 0x7ff000
No RedBoot partition table detected in spi0.0
spi0.0: no WRT160NL signature found
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=596000, len=25A000
0x000000596000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "art"
0x000000020000-0x0000007f0000 : "firmware"
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xba000000, irq 5
eth0: Found an AR7240 built-in switch
eth1: Atheros AG71xx at 0xb9000000, irq 4
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 168k freed
input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
eth0: link down

Please press Enter to activate this console. device eth0 entered promiscuous mode
Compat-wireless backport release: compat-wireless-2011-05-11-1-g501c91f
Backport based on wireless-testing.git master-2011-05-13
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
cfg80211: World regulatory domain updated:
cfg80211:    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
usbcore: registered new device driver usb
ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=72
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
cfg80211:    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211:    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211:    (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
nf_conntrack version 0.5.0 (462 buckets, 1848 max)
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
JFFS2 notice: (1300) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
eth0: link up (1000Mbps/Full duplex)
br-lan: port 1(eth0) entering forwarding state
br-lan: port 1(eth0) entering forwarding state

xll · 发表于 2011-6-30 11:13

ar7240> ?
?    - alias for 'help'
base - print or set address offset
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
cmp    - memory compare
cp    - memory copy
crc32 - checksum calculation
erase - erase FLASH memory
flinfo  - print FLASH memory information
go    - start application at address 'addr'
help - print online help
loadb - load binary file over serial line (kermit mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md    - memory display
mm    - memory modify (auto-incrementing)
mtest - simple RAM test
mw    - memory write (fill)
nm    - memory modify (constant address)
printenv- print environment variables
progmac - Set ethernet MAC addresses
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
setenv  - set environment variables
tftpboot- boot image via network using TFTP protocol
version - print monitor version
reset - Perform RESET of the CPU

xa163 · 发表于 2011-7-1 11:49

这些是UBOOT命令，用cp.b命令

abiao3k · 发表于 2011-7-9 17:09

mark

账号		自动登录	找回密码
密码			立即注册

FW300R 到底能不能TTL刷机？？？

相关帖子

欢迎大家光临恩山无线论坛 1/1