FW150R v5

729650915

今天刚到货 直接拆了
板子...好小一块

已经找到TTL
短接R173 然后背面TP18飞线到TP28 J1粗线开始分别为tx rx gnd vcc


TTL输出



         ________  ________             __      __  ____   _  __   ___
        |________||   ___  |           |  |    |  ||    \ | ||  | /  /
           |  |   |  |___| |   __ __   |  |    |  ||     \| ||  |/  /
           |  |   |   _____|  |__ __|  |  |___ |  || |\     ||      \
           |__|   |__|                 |______||__||_| \____||__|\___\


                            Software Platform for MIPS
Creation date: Jan 25 2011, 15:02:06 (chenyunchuan@tp-link.net)
Copyright(C) 2001-2010 by TP-LINK TECHNOLOGIES CO., LTD.
CPU: AR9330: AP121 Board
CPU freq: 400 MHZ
SDRAM size: 8 MB
ipaddr:192.168.1.1
serverip:192.168.1.100
file:vxWorks.img


Attaching interface lo0... done
Rx clbufs 512 each of size 1756
eth_rx_netpool_init: allocated, pDmaBuf=0x806af110, buffend = 8078b914
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth_rx_netpool_init: done already!
Attached IPv4 interface to eth unit 0
Press Ctrl+C to stop auto-boot...
0
auto-booting...
Uncompressing...done
Starting at 0x80001000...

Attaching interface lo0... done
Rx clbufs 512 each of size 1756
eth_rx_netpool_init: allocated, pDmaBuf=0x80e98460, buffend = 80f74c64
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth_rx_netpool_init: done already!
Attached IPv4 interface to mirror unit 0
usrAppInitEx: 107: GPIO_OE = c00081d
usrAppInitEx: 108: CP0 CONFIG = 80208483
usrAppInitEx: 109: CP0 CONFIG1 = 9ee3519e

-->starting wireless...
APCFG task id 80cd2270
sysWlanInit ...
Create WLAN event task tWLANEventTask
Create mem partion 0x80cbea40 for size 28672
Restoring Cal data from Flash
ath_get_caps[4267] rx chainmask mismatch actual 1 sc_chainmak 0
ath_get_caps[4242] tx chainmask mismatch actual 1 sc_chainmak 0
Create OS_MESGQ Successfully at 0x80cad6b0
osifp->queue_head = 0x80cad988
ag7240MemInit: allocated, dmabuf=0x80bf8cb0, buffend = 80ca0eb4
Reading Flash
FLASH NVARAM APCFG ID WRONG, COMIT FIRST
Entering Task Loop
Entering WLAN event Task Loop
AP_AUTOSTART=0
ERROR:wireless OR ACL disable
-->wlan start outside!
sending message 80bda0d0,24
TDDP: Now listening client request.
tddp is running.
httpInit: System File Registry successfully initialized.
httpInit: System File Manager successfully initialized.
httpInit: File System RPM successfully initialized.
httpInit: RPM dispatcher successfully initialized.
httpInit: MIME type guessing RPM successfully initialized.
httpInit: http Password Checking successfully initialized.
httpInit: http Access Control successfully initialized.

729650915

Software Platform for MIPS
  Copyright(C) 2001-2010 by TP-LINK TECHNOLOGIES CO., LTD.
  Creation date: Mar 14 2011, 15:06:55
# Starting WLAN !!!!
AP_STARTMODE=standard
AP_ENABLE=1
ATH_COUNTRYCODE=170
wlan_vap_create : enter. devhandle=0x803f90f0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x803f90f0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
osif_ioctl_create_vap: vap 0x80ffe9b0 vap->iv_unit 0
ieee80211_end_load: load done
ath0 end flag = 0x00028802
default
default
default
IEE80211-FREQ IOCTL vap 0x80ffe9b0 0,0,0
AP_CHMODE=11NGHT40PLUS

WLAN IOCTL AP_CHMODE=11NGHT40PLUS=11NGHT20=11NGHT40PLUS=1003
IEE80211-MODE IOCTL 1,11NGHT40PLUS,13
set mode 11,-2130709068,6
set mode retv 0

WLAN IOCTL AP_PRIMARY_CH=auto=1=auto=1002
IEE80211-FREQ IOCTL vap 0x80ffe9b0 0,0,11

WLAN IOCTL PUREG=0=0=0=1004
IEEE80211-SETPURGE IOCTL 0

WLAN IOCTL AP_HIDE_SSID=0=0=0=1005
IEEE80211-SETHIDESSIDIOCTL 0

WLAN IOCTL AP_ISOLATION=0=0=0=1034
IEE80211-setparam-nobridge 0

WLAN IOCTL AP_TX11NRATE==0=0=1041
set auto rate

WLAN IOCTL AP_11G_PROTECTION==0=0=1042

WLAN IOCTL AP_BEACON_INTERVAL=100=100=100=1043

WLAN IOCTL AP_FRAGMENT_THRESHOLD=2346=2346=2346=1044

WLAN IOCTL AP_RTS_THRESHOLD=2346=2347=2346=1046

WLAN IOCTL AP_DTIM_PERIOD=1=1=1=1045

WLAN IOCTL AP_WMM_ENABLE=1=1=1=1051

WLAN IOCTL AP_WMM_NOACK==0=0=1052
IOCTL set wmm noack 0

WLAN IOCTL AP_CYPHER_2==CCMP=CCMP=1000
Get EIOCGADDR

WLAN IOCTL AP_NO_EDGE_CH==0=0=1056

WLAN IOCTL AP_MCASTRATE==0=0=1018

WLAN IOCTL AP_MACFILTER_MODE==0=0=1038

WLAN IOCTL AP_MACFILTER_LIST====1000
Get EIOCGADDR

WLAN IOCTL AP_SHORT_GI=1=1=1=1055

WLAN IOCTL AP_SSID=FAST_65DA16=Hornet_test_xxxxxxx=FAST_65DA16=1001
IEE80211-ESSID IOCTL 1,FAST_65DA16,12
AP_CHMODE=11NGHT40PLUS
AP_CWMMODE=1
IEE80211-CWMMODE IOCTL 1
AP_AMPDU=0
AP_PURE_N=0
AP_TX_CHAINMASK=1
AP_RX_CHAINMASK=1
AP_SECMODE=None
WPS_ENABLE=1
AP_MACFILTER_MODE=0
ieee80211_open

WLAN IOCTL AP_BASICRATES==0=0=1039

WLAN IOCTL AP_DEBUG=0=0=0=1062

WLAN IOCTL AP_TX_POWER==0=0=1073
Starting Hostapd
AP_SSID=FAST_65DA16
AP_HOSTAPD_DEBUG=0
AP_IPADDR=192.168.1.2
AP_SECMODE=None
WPS BSS init
WPS_ENABLE=1
WPS_PIN=29328802
WPS_STATE=1
AP_SECMODE=None
WPS OPEN BSS init
starting hostapd ...
Hostapd task Created 80b6ff90
Task details [80b6ff90,,64,80cd2010]
Adding ath0 in bridge ...
default
Set EIOCGMIB2
default
Entering Hostapd Main
default
Set EIOCGMIB2
attached backend socket .
Attached backend socket for eth0
Attached backend socket for eth1
Attached backend socket for mirror 0
@@@@ kris-hostapd vapid=0 @@@@@ wiface=ath0 @@@@
**** [0,1,0,0192.168.1.2,]****
Just before eloop_run()
*** setup interface1 started ****
Eapol sockfd=27
Get EIOCGADDR
MAC address 40,16,ffffff9f,65,ffffffda,16
link _ubind0,0,0,0,0,0
IEE80211-IWMODE IOCTL  3
IEE80211-setparam-privacy 0
1136073607.533333: Defaulted uuid based on mac addr 40:16:9f:65:da:16
ieee80211_ioctl_setappiebuf
ieee80211_ioctl_setappiebuf
ieee80211_ioctl_setappiebuf
Madwifi init completed
*** setup interface1 completed ****
*** setup interface2 started ****
IOCTL setmlme
[ieee80211_ioctl_setmlme:1893] data=0x80b6fab0,data->pointer=0x80b6fb00, data->length=42
[ieee80211_ioctl_setmlme:1899] mlme->im_op=3
IEE80211-setparam-privacy 0
ieee80211_ioctl_delkey : idk_keyix=0
ieee80211_ioctl_delkey : idk_keyix=1
ieee80211_ioctl_delkey : idk_keyix=2
ieee80211_ioctl_delkey : idk_keyix=3
Using interface ath0 with hwaddr 40:16:9f:65:da:16 and ssid 'FAST_65DA16'
IEE80211-ESSID IOCTL 1,FAST_65DA16,12
IEE80211-setparam-authmode 1
osif_vap_init 0
hostapd_ctrl_iface_init
1136073608.050000: upnp_wps_device_init called
1136073608.050000: upnp_wps_device ssdp_listener_start failure!
1136073608.050000: upnp_wps_device_stop ENTER
1136073608.050000: upnp_wps_device_deinit called
1136073608.066667: upnp_wps_device_stop ENTER
1136073608.066667: Failed to initialize UPnP state machine
1136073608.066667: Continuing with WPS UPnP disabled.
****setup interface2 completed****
****setup interface finalized ****
osif_ht40_event_handler

729650915

这货现在没GPL..鸭梨很大 待会试下把741固件塞进去
另外很奇怪为啥明明是16M内存 却只认8M

oliver01

拆的真快，支持一下

浮云聚散

貌似DDR内存。。有具体型号看看？

shwshw

能不改造刷dd吗

zhe_jiang

usb口好像没接出来吧？
不知道MW300R是否有USB接出来?

729650915

今天改了32M内存 依然只认8M
另外成功刷进wr740n v5的固件
编程器固件在附件里
0x1e0000是mac
0x1e0010是pin

chkai1981

顶楼主，我的150R又能活过来了

元元0101

lz haoya

xtwuyou

楼主强人 人工置顶一次

zhe_jiang

mark

meteormatt

能不改造刷dd吗
shwshw 发表于 2011-8-2 15:57

目前还不行.
我等满1年了刷DD-WRT.
那时候,驱动应该差不多写好了.

lilihust

楼主强人加好人

adoot

目前还不行.
我等满1年了刷DD-WRT.
那时候,驱动应该差不多写好了.
meteormatt 发表于 2011-8-11 21:12

这个只有2M Flash，16M内存，刷DDWRT或者OPENWRT很困难。
OPENWRT上面有对应的AP121-Mini固件，体积也达到了4MB。